1996 TOYOTA LAND CRUISER transmission oil

Q08467
Rear Propeller
ShaftTransfer Shift
Lever Boot
Transmission Shif
Lever Assembly
Rear Console Box
Front Console Box
Engine Rear Mounting
Plug for Hydraulic Test
Oil Cooler Pipe Transfer Shift
Control Link
Transfer Shift
Lever Cushion
x 6
x 6 Clip
Transfer Shift
Lever Knob
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−19
803
Author: Date:
1996 LAND CRUISER (RM451U)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT−22
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(i) Remove the 4 bolts and transfer shift lever.
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
(j) Remove the 2 cushions.
6. DISCONNECT THESE CONNECTORS:
No.1 vehicle speed sensor
No.2 vehicle speed sensor
Park/neutral position switch
Solenoid connector
ATF temperature sensor
Center differential lock indicator switch
L4 position switch
Neutral position switch
7. DISCONNECT BLEEDER HOSE FROM TRANSFER
8. REMOVE FRONT AND REAR PROPELLER SHAFT (See page PR−3 )
9. REMOVE OIL FILLER PIPE
(a) Remove the level gauge.
(b) Remove the upper side mounting bolt.
(c) Remove the bolt and filler pipe.
HINT:
At the time of installation, replace the used O −ring with a new
one.
10. LOOSEN 2 OIL COOLER PIPE UNION NUTS
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07409
AT−24
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
1996 LAND CRUISER (RM451U)
(d) Remove the 4 nuts and 2 gaskets, shift the front exhaust
pipe assembly to the vehicle’s outside.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
HINT:
At the time of installation, replace the used gaskets and nuts
with new gaskets and nuts.
15. REMOVE STARTER
(a) Remove the nut and disconnect the terminal and connec-
tor.
(b) Remove the lower side mounting bolt and starter. Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
16. REMOVE CROSSMEMBER
(a) Support the transmission with a transmission jack.
(b) Remove the 8 bolts and 2 nuts, and then remove the crossmember.
Torque:
Bolt: 61 N·m (620 kgf·cm, 45 ft·lbf)
Nut: 74 N·m (750 kgf·cm, 54 ft·lbf)
17. REMOVE TRANSMISSION
(a) Lower the rear end of the transmission.
NOTICE:
Be careful not to damage the cooling fan, brake booster
and brake line.
(b) Separate the wire harness from the transmission and transfer.
(c) Remove the oil cooler pipe mounting bolts from the torque
converter clutch housing, and then disconnect the 2 oil
cooler pipes from the elbows.
(d) Remove the 10 bolts and transmission. Torque: 72 N·m (730 kgf·cm, 53 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

CO118−01
CO−16
−
COOLING RADIATOR
1996 LAND CRUISER (RM451U)
INSTALLATION
1. INSTALL RADIATOR
(a) Install the 2 radiator brackets with the 4 nuts. Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)
(b) Install the radiator with the 2 bolts and 2 nuts. Torque:
Bolt: 18 N·m (185 kgf·cm, 13 ft·lbf)
Nut: 12 N·m (120 kgf·cm, 9 ft·lbf)
2. CONNECT A/T OIL COOLER HOSES
3. CONNECT RADIATOR OUTLET HOSE
4. INSTALL WATER PUMP PULLEY, FAN SHROUD, FAN WITH FLUID COUPLING AND DRIVE BELTS
(a) Place the fan with fluid coupling, water pump pulley and fan shroud in position.
(b) Temporarily install the fan pulley mounting nuts.
(c) Install the fan shroud with the 2 bolts. Torque: 5.0 N·m (50 kgf·cm, 43 in.·lbf)
(d) Connect the oil cooler hose to the clamp on the fan
shroud.
(e) Install the drive belts with the adjusting bolt and pivot bolt.
(f) Stretch the belts tight and tighten the 4 water pump pulley mounting nuts.
(g) Adjust the drive belts (See page CH−2 ).
5. CONNECT RADIATOR RESERVOIR HOSE
6. CONNECT RADIATOR INLET HOSE
7. CONNECT NO.3 WATER BYPASS HOSE
8. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
9. INSTALL BATTERY AND BATTERY TRAY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery with the hold−down clamp and nuts.
(d) Connect the battery cables.
10. FILL RADIATOR WITH ENGINE COOLANT
11. START ENGINE AND CHECK FOR LEAKS
12. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07308
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
Q07309
DI−138
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem- perature 70 − 80° C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transmission.
If there are leaks, it is necessary to repair or replace O −rings,
Seal packings, oil seals, plugs or other parts.
(e) Inspect and adjust the throttle cable. (1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable endand stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not standard, adjust the cable by the adjusting
nuts.
(f) Inspect and adjust the shift lever position. When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.
If the indicator is not aligned with the correct position, carry out
the following adjustment procedures. (1) Loosen the nut on the control rod.
(2) Push the control rod fully rearward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−141
1996 LAND CRUISER (RM451U)
8. HYDRAULIC TEST
Measure the line pressure.
NOTICE:
Do the test at normal operation ATF temperature 50 − 80°C (122 − 176° F).
The line pressure test should always be carried out in pairs. One techni\
cian should observe
the conditions of wheels or wheel stoppers outside the vehicle while the ot\
her is doing the test.
Be careful to prevent SST’s hose from interfering with the exhaust pipe.
(1) Warm up the ATF.
(2) Remove the test plug on the transmission case right side and connect SST\
(See page AT−18
for the location to connect SST).
SST 09992 −00094 (09992 −00150, 09992−00270)
(3) Fully apply the parking brake and chock the 4 wheels.
(4) Start the engine and check idling speed.
(5) Keep your left foot pressed firmly on the brake pedal and shift into D p\
osition.
(6) Measure the line pressure when the engine is idling.
(7) Press the accelerator pedal all the way down. Quickly read the highest line pr\
essure when engine
speed reaches stall speed.
NOTICE:
Release the accelerator pedal and stop test if the rear wheels begin to rotate before the engine speed
reaches the specified stall speed.
(8) In the same manner, do the test in R position.
Specified line pressure:
Condition D position kPa (kgf/cm2, psi) R position kPa (kgf/cm2, psi)
Idling422 −
481 (4.3 − 4.9, 61 − 70)510 − 608 (5.2 − 6.2, 74 − 88)
Stall1,285 − 1,530 (13.1 − 15.6, 128 − 153)1,579 − 1,932 (16.1 − 19.7, 158 − 193)
If the measured pressures are not up to specified values, recheck the thro\
ttle cable adjustment and retest.
Evaluation:
ProblemPossible cause
If the measured value at all positions are higher
Throttle cable out of adjustment
 Throttle valve defective
 Regulator valve defective
If the measured value at all positions are lower
Throttle cable out of adjustment
 Throttle valve defective
 Regulator valve defective
 Oil pump defective
 O/D direct clutch defective
If pressure is low in the D position onlyD position circuit fluid leakage
 Forward clutch defective
If pressure is low in the R position only
R position circuit fluid leakage
 Direct clutch defective
 1st and reverse brake defective
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KE−03
Vd762D00115
E4
11
12
13 1415
16
10 12
3
4
567
8
9
10
11
12
123
456
7
1
2
34
56
8910
11
7
8
9
12141516 13
17181920
21
22
23
242526
ECM T
erminals
1
23
4
5
6
7
89
10
11
13 12
15
16
171819202122 14
E5E6E7
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−145
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (T erminal No.)Wiring ColorConditionSTD Voltage (V)
SPD (E7−8) − E1 (E4− 24)L− W − BR− B
Disconnect cruise control connector and IG ON StationaryBelow 1.5
Disconnect cruise control connector and IG ON
Turn one rear wheel slowlyPulse signal is outputBelow 1.5 ↔ 4 − 6
S1 (E4− 10) − E1 (E4− 24)R − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ON9 − 14
1st or 2nd gear9 − 14
3rd or O/D gearBelow 1.5
S2 (E4− 9) − E1 (E4− 24)R−Y − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
2nd or 3rd gear9 − 14
1st or O/D gearBelow 1.5
SL (E4− 8) − E1 (E4− 24)R−L − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
Vehicle driving under lock −up position9 − 14
SP2+ (E6− 2) − SP− (E6− 8)V − V−G
IG OFF Disconnect ECM connector560 − 680 Ω
Engine is runningPulse signal is output
Below 1.5 ↔ 4 − 6
OD1 (E7− 18) − E1 (E4− 24)G−O − BR− BIG ON9 − 14
OD2 (E7− 19) − E1 (E4− 24)P−L − BR− BO/D main switch ON (O/D OFF)Below 3
O/D main switch OFF (O/D ON)9 − 14
OIL (E5− 12) − E2 (E5− 9)R−W − BR− BATF temperature: 110 °C (230° F)Below 1.5
L (E7−17) − E1 (E4− 24)G−W − BR− BIG ON Shift lever L position7.5 − 14
IG ON Shift lever other than L positionBelow 1.5
2 (E7−16) − E1 (E4− 24)O − BR− BIG ON Shift lever 2 position7.5 − 14
IG ON Shift lever other than 2 positionBelow 1.5
R (E7−15) − E1 (E4− 24)R−B − BR− BIG ON Shift lever R position7.5 − 14
IG ON Shift lever other than R positionBelow 1.5
NSW (E7−22) − E1 (E4− 24)B−W − BR− BIG ON Shift lever P or N positionBelow 3
IG ONShift lever other than P and N position9 − 14
STP (E7− 14) − E1 (E4− 24)G−W − BR− BIG ON Brake pedal is depressed7.5 − 14
IG ON Brake pedal is releasedBelow 1.5
THW (E5−4) − E2 (E5− 9)R−W − BR− BIG ON Engine coolant temperature 80 °C (176° F)Below 1.5
IDL (E5− 11) − E2 (E5− 9)G−W − BR− BIG ON Accel. pedal is releasedBelow 1.5
IG ONAccel. pedal is depressed9 − 14
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−151
1996 LAND CRUISER (RM451U)
Slip or shudder (Forward and reverse)
1. Throttle cable
2. Transmission control rod
3. Oil strainer
4. Pressure relief valve
5. Off
−vehicle repair matrix chartDI−131
DI−131

−
Slip or shudder (Particular position)
1. Throttle cable
2. Transmission control rod
3. Off −vehicle repair matrix chartDI−131
DI−131
−
No engine braking (1st (L position))1. Low coast modulator
2. Off −vehicle repair matrix chart
−
No engine braking (2nd (2 position))1. 2nd coast modulator
2. Off −vehicle repair matrix chart
−
No kick− down1. 1−2 shift valve
2. 2 −3 shift valve

Chapter 3: Off −Vehicle Repair
(  : A340F, A343F Automatic Transmission Repair Manual Pub. No. RM479U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion1. O/D one− way clutch (F0)
2. O/D planetary gear unit
3. Torque converter clutch

AT −26
Vehicle does not move in R position
1. 2nd coast brake (B1)
2. Front and rear planetary gear unit
3. Direct clutch (C
2)
4. 1st and reverse brake (B
3)




Vehicle does not move in D, 2 and L positions1. Forward clutch (C1)
Vehicle does not move in D and 2 positions1. No. 2 one− way clutch (F2)
Vehicle does not move in 2 position1. 1st and reverse brake (B3)
Vehicle does not move in L position
1. 2nd brake (B2)
2. 2nd coast brake (B
1)
3. Direct clutch (C
2)



No up− shift (1st → 2nd)1. 2nd brake (B2)
2. No. 1 one− way clutch (F
1)


No up−shift (2nd → 3rd)1. Direct clutch (C2)
No up−shift (3rd → O/D)1. O/D brake (B0)
No down−shift (2nd → 1st)1. 2nd brake (B2)
Lock−up does not engage or lock −up does not disengage1. Torque converter clutchAT −26
Harsh engagement (N → D)
1. Forward clutch (C1)
2. O/D one− way clutch (F
0)
3. No. 2 one− way clutch (F
2)



Harsh engagement (N → R)
1. Direct clutch (C2)
2. 1st and reverse brake (B
3)
3. O/D one− way clutch (F
0)



Harsh engagement (2nd → 3rd)1. Direct clutch (C2)
Harsh engagement (3rd → O/D)1. O/D brake (B0)
2. O/D planetary gear unit

Harsh engagement (O/D → 3rd)1. O/D one− way clutch (F0)
Harsh engagement (Lock −up)1. Torque converter clutchAT −26
Slip or shudder (Forward and reverse (After warm −up))
1. Torque converter clutch
2. O/D one− way clutch (F
0)
3. O/D direct clutch (C
0)
AT −26


Slip or shudder (Forward and reverse (Just after engine starts))1. Torque converter clutchAT −26
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010