1996 TOYOTA LAND CRUISER Battery circuit

Z06302
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
BE−47
1996 LAND CRUISER (RM451U) OFF
1 −
2 − 11 − 14Continuity
DOWN1 − 2 − 11
7 − 8 − 14Continuity
Rear Right Switch (Window lock):
Switch positionTester connectionSpecified condition
UP7 − 8 − 11Continuity
OFF11 − 14Continuity
DOWN7 − 8 − 14Continuity
If continuity is not as specified, replace the master switch.
2. INSPECT POWER WINDOW MASTER SWITCH ILLU-
MINATION
(a) Set the window lock switch to the unlock position.
(b) Connect the positive (+) lead from the battery to terminal 7 and the negative ( −) lead to terminal 1, and check that
all the illuminations light up.
(c) Set the window lock switch to the lock position, and check that all the passenger’s power window switch illumina-
tions go out.
If operation is not as specified, replace the master switch.
3. Using an ammeter: INSPECT ONE TOUCH POWER WINDOW SYSTEM
(a) Disconnect the connector from the master switch.
(b) Connect the positive (+) lead from the ammeter to termi- nal 6 on the wire harness side connector and the negative
(−) lead to negative terminal of the battery.
(c) Connect the positive (+) lead from the battery to terminal 13 on the wire harness side connector.
(d) As the window goes down, check that the current flow is up to approximately 7 A.
(e) Check that the current increases approximately 14.5 A or more when the window stops going down.
HINT:
The circuit breaker opens some 4 − 40 seconds after the win-
dow stops going down, so that check must be made before the
circuit breaker operates.
If the operation is as specified, replace the master switch.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06303
Z06304
BE−48
−
BODY ELECTRICAL POWER WINDOW CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
4. Using an ammeter with a current − measuring probe:
INSPECT ONE TOUCH POWER WINDOW SYSTEM
(a) Remove the master switch with connector connected.
(b) Attach a current−measuring probe to terminal 6 of the
wire harness.
(c) Turn the ignition switch ON, and set the power window switch in the down position.
(d) As the window goes down, check that the current flow is up to approximately 7 A.
(e) Check that the current increases approximately 14.5 A or more when the window stops going down.
HINT:
The circuit breaker opens some 4 − 40 seconds after the win-
dow stops going down, so check must be made before the cir-
cuit breaker operates.
If operation is as specified, replace the master switch.
5. INSPECT POWER WINDOW SWITCH CONTINUITY
Switch positionTester connectionSpecified condition
UP1 − 5, 3 − 4Continuity
OFF1 − 2, 3 − 4Continuity
DOWN1 − 2, 4 − 5Continuity
If continuity is not as specified, replace the switch.
6. Front Door:
INSPECT LEFT SIDE DOOR POWER WINDOW MO-
TOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
3 and the negative ( −) lead to terminal 1, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
7. Rear Door: INSPECT LEFT SIDE DOOR POWER WINDOW MO-
TOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 2, and check that
the motor turns counterclockwise.
(b) Reverse the polarity, and check that the motor turns
clockwise.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
BE−55
1996 LAND CRUISER (RM451U)9 −
Ground
Driver’s door key lock and unlock switch position
UNLOCK (Door key turned to unlock)Continuity
10 − GroundDoor lock manual switch position OFF or
UNLOCKNo continuity
10 − GroundDoor lock manual switch position LOCKContinuity
11 − Ground
Door lock manual switch and passenger’s door
key lock and unlock switch position OFF or
UNLOCK
No continuity
11 − GroundDoor lock manual switch and passenger’s door
key lock and unlock switch position UNLOCKContinuity
12 − Ground
Driver’s and passenger’s door key lock and
unlock switch position OFF or UNLOCK (Door
key free or turned to unlock)
No continuity
12 − GroundDriver’s or passenger’s door key lock and unlock
switch position LOCK (Door key turned to lock)Continuity
14 − GroundPassenger’s door courtesy switch position OFF
(Door closed)No continuity
14 − GroundPassenger’s door courtesy switch position ON
(Door opened)Continuity
16 − GroundConstantContinuity
1 − GroundIgnition switch position LOCK or ACCNo voltage
1 − GroundIgnition switch position ONBattery positive voltage
8 − GroundConstantBattery positive voltage
If circuit is as specified, inspect the door lock signal.
If the circuit is not as specified, inspect the circuits connected
to other parts.
11. INSPECT DOOR LOCK SIGNAL
HINT:
When the relay circuit is as specified, inspect the door lock sig-
nal.
(a) Connect the connector to the relay.
(b) Connect the positive (+) lead from the voltmeter to termi-
nal 3 and the negative ( −) lead to terminal 4.
(c) Set the door lock manual switch to UNLOCK, and check
that the voltage rises from 0 V to battery positive voltage
for approximately 0.2 seconds.
(d) Reverse the polarity of the voltmeter leads.
(e) Set the door lock manual switch to LOCK, and check that the voltage rises from 0 V to battery positive voltage for
approximately 0.2 seconds.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−56
−
BODY ELECTRICAL POWER DOOR LOCK CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
12. NSPECT KEY−OFF POWER WINDOW SIGNAL
HINT:
When the relay circuit is as specified, inspect the key −off power
window signal.
(a) Connect the connector to the relay.
(b) Connect the positive (+) lead from the voltmeter to termi- nal 15 and the negative ( −) lead to terminal 16.
(c) Close the door with ignition switch truned to LOCK or ACC, check that the meter needle indicates battery posi-
tive voltage.
(d) Open the door, check that the meter needle indicates 0 V.
(e) Turn the ignition switch ON, check that the meter needle
indicate battery positive voltage again.
If operation is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−60
−
BODY ELECTRICAL SLIDING ROOF SYSTEM
1996 LAND CRUISER (RM451U) 3 −
Ground
Sliding roof control switch position (TILT) OFF or
DOWNNo continuity
3 − GroundSliding roof control switch position (TILT) UPContinuity
4 − GroundConstantNo continuity
4 − 5Constant*1Continuity
5 − GroundConstantNo continuity
7 − GroundSliding roof control switch position (TILT) OFF or
UPNo continuity
7 − GroundSliding roof control switch position (TILT) DOWNContinuity
8 − GroundNo.1 limit switch position OFF (Sliding roof tilted
up or open approx. 200 mm (7.87 in.))No continuity
8 − GroundNo.1 limit switch position ON (Except for
conditions mentioned above)Continuity
9 − GroundNo.2 limit switch position OFF (Sliding roof
closed)No continuity
9 − GroundNo.2 limit switch position ON (Sliding roof open)Continuity
11 − GroundConstantContinuity
6 − GroundIgnition switch position LOCK or ACC*2No voltage
6 − GroundIgnition switch position ONBattery positive voltage
12 − GroundConstantBattery positive voltage
*1: There is resistance because this circuit is include motor.
*
2: Exceptions: During 60 second period after ignition switch
ON → OFF (ACC) or until driver or passenger door is opened
after ignition switch ON → OFF (ACC).
If circuit is as specified, replace the relay.
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
7. INSPECT POWER MAIN RELAY CONTINUITY (See page BE−46 )
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
BE−63
1996 LAND CRUISER (RM451U)
2. INSPECT POWER SEAT SWITCH (PASSENGER’S
SIDE) CONTINUITY
Slide switch:
Switch positionTester connectionSpecified condition
FORWARD5 − 10, 8 − 9Continuity
OFF5 − 8 − 9Continuity
BACKWARD5 − 9, 8 − 10Continuity
Front vertical switch:
Switch positionTester connectionSpecified condition
UP4 − 11, 10 − 12Continuity
OFF4 − 11 − 12Continuity
DOWN4 − 12, 10 − 11Continuity
Rear vertical switch:
Switch positionTester connectionSpecified condition
UP2 − 10, 6 − 7Continuity
OFF2 − 6 − 7Continuity
DOWN2 − 7, 6 − 10Continuity
Reclining switch:
Switch positionTester connectionSpecified condition
FORWARD4 − 10, 7 − 9Continuity
OFF4 − 7 − 9Continuity
BACKWARD4 − 9, 7 − 10Continuity
If continuity is not as specified, replace the switch.
3. INSPECT SLIDE MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2, and check that
the motor turns counterclockwise.
(b) Reverse the polarity, and check that the motor turns clockwise.
If operation is not as specified, replace the motor.
4. INSPECT SLIDE MOTOR CIRCUIT BREAKER OPERA-
TION
(a) Connect the positive (+) lead and the negative ( −) lead
from the battery to slide motor connector (illustrated termi-
nals), and slide the seat to front end position.
(b) Continue to apply voltage, check that there is a circuit breaker operation noise within 4 to 60 seconds.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE−64
−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
(c) Reverse the polarity, and check that the seat begins to
move backwards within approximately 60 seconds.
If operation is not as specified, replace the motor.
5. INSPECT FRONT VERTICAL MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal
1 and the negative ( −) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity, check that the motor turns counter- clockwise.
If operation is not as specified, replace the motor.
6. INSPECT FRONT VERTICAL MOTOR CI RCUIT
BREAKER OPERATION
(a) Connect the positive (+) lead and the negative ( −) lead
from the battery to the front vertical motor connector (illus-
trated terminals), and move the front edge of seat cushion
to the highest position.
(b) Continue to apply voltage, and check that there is a circuit breaker operation noise within 4 to 60 seconds.
(c) Reverse the polarity , and check that the seat cushion be-
gins to descend within approximately 60 seconds.
If operation is not as specified, replace the motor.
7. INSPECT REAR VERTICAL MOTOR OPERATION
(a) Connect the positive (+) lead from the battery to terminal 2 and the negative ( −) lead to terminal 1, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
BODY ELECTRICAL POWER SEAT CONTROL SYSTEM
BE−65
1996 LAND CRUISER (RM451U)
8. INSPECT REAR VERTICAL MOTOR CIRCUIT BREAK-
ER OPERATION
(a) Connect the positive (+) lead and the negative ( −) lead
from the battery to the rear vertical motor connector (illus-
trated terminals), and move the front edge of seat cushion
to the highest position.
(b) Continue to apply voltage, and check that there is a circuit
breaker operation noise within 4 to 60 seconds.
(c) Reverse the polarity, check that the seat cushion begins to descend within approximately 60 seconds.
If operation is not as specified, replace the motor.
9. INSPECT RECLINING MOTOR (DRIVER’S SIDE) OP- ERATION
(a) Connect the positive (+) lead from the battery to terminal 1 and the negative ( −) lead to terminal 2, and check that
the motor turns clockwise.
(b) Reverse the polarity, and check that the motor turns coun-
terclockwise.
If operation is not as specified, replace the motor.
10. INSPECT RECLINING MOTOR (DRIVER’S SIDE) CIR- CUIT BREAKER OPERATION
(a) Connect the positive (+) lead from terminal 1 and negative
(−) lead to terminal 2.
Check that the seat back reclines to the most forward
position.
(b) Continue to apply voltage, and check that there is a circuit breaker operation noise within 4 to 40 seconds.
(c) Reverse the polarity, and check that the seat back starts
to fall backwards within approximately 60 seconds.
If operation is not as specified, replace the motor.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010