1996 TOYOTA LAND CRUISER − AUTOMATIC TRANSMISSION PARK

Q07312
DI−142
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
9. MANUAL SHIFTING TEST
The purpose of this manual shifting test is to determine whether
a problem is caused by either mechanical or electrical factors.
Disconnecting the solenoid wire disables electrically −con-
trolled automatic gear shifting. In this case, operating the shift
lever is the only way to shift the transmission gear. If the gear
is not changed by shift lever operation, it is assumed that there
is a mechanical problem.
(a) Turn the ignition switch OFF.
(b) Disconnect the solenoid wire connector.
(c) Warm up the engine.
(d) Drive the vehicle.
(e) Check the transmission operation when the shift lever is moved into L, 2 and D positions.
Standard:
Shift LeverOperation
L to 2Shift up
2 to DShift up
D to 2Shift down
2 to LShift down
(f) Turn the ignition switch OFF.
(g) Connect the solenoid wire connector.
(h) Clear DTCs.
HINT:
When the solenoid wire is disconnected, the transmission gear
will be set as listed below:
Shift LeverGear
PParking
RReverse
NNeutral
DO/D (4th)
23rd
L1st
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KB−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−143
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a DTC is displayed during the DTC check, check the circuit listed for that code i\
n the table below and pro-
ceed to the page given.
DTC No.
(See page)Detection ItemTrouble AreaMIL*Memory
P0500
( DI−153 )Vehicle Speed Sensor Malfunc-
tion
(No. 1 Vehicle Speed Sensor)Open or short in No. 1 vehicle speed sensor circuit
 No. 1 vehicle speed sensor
 ECM

P0710
( DI−154 )Transmission Fluid Temperature
Sensor Malfunction
(ATF Temperature Sensor) Open or short in ATF temperature sensor circuit
 ATF temperature sensor
 ECM

P0750
( DI−156 )Shift Solenoid A Malfunction
(Shift Solenoid Valve No. 1)Shift solenoid valve No. 1 is stuck open or closed
 Valve body is blocked up or stuck
P0753
( DI−157 )Shift Solenoid A Electrical
Malfunction
(Shift Solenoid Valve No. 1)Open or short in shift solenoid valve No. 1 circuit
 Shift solenoid valve No. 1
 ECM

P0755
( DI−156 )Shift Solenoid B Malfunction
(Shift Solenoid Valve No. 2)Shift solenoid valve No. 2 is stuck open or closed
 Valve body is blocked up or stuck
P0758
( DI−157 )Shift Solenoid B Electrical
Malfunction
(Shift Solenoid Valve No. 2)Open or short in shift solenoid valve No. 2 circuit
 Shift solenoid valve No. 2
 ECM

P0770
( DI−161 )Shift Solenoid E Malfunction
(Shift Solenoid Valve SL)Shift solenoid valve SL is stuck open or closed
 Valve body is blocked up or stuck
 Lock− up clutch

P0773
( DI−163 )Shift Solenoid E Electrical
Malfunction
(Shift Solenoid Valve SL)Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM

P1700
( DI−166 ) Speed Sensor No. 2 Circuit
Malfunction
(No. 2 Vehicle Speed Sensor)Open or short in No. 2 vehicle speed sensor circuit
 No. 2 vehicle speed sensor
 ECM

P1780
( DI−169 )Park/Neutral Position Switch
MalfunctionShort in park/neutral position switch circuit
 Park/neutral position switch
 ECM

*:  ...MIL light up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KD−02
Q08236
No. 1 Vehicle
Speed Sensor
O/D OFF Indicator Light
MIL
Pattern Select Switch O/D Main Switch
DLC1
Shift Solenoid Valve SL
ECM
Stop Light Switch L4 Position Sensor
Park/Neutral Position Switch No. 2 Vehicle Speed Sensor
Shift Solenoid Valve No. 2
Shift Solenoid Valve No. 1
Engine Coolant Temperature Sensor
Throttle Position Sensor
ATF Temperature Sensor
DLC3
Transfer Neutral
Position Switch
DI−144
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
PARTS LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KH−03
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−147
1996 LAND CRUISER (RM451U)
PROBLEM SYMPTOMS TABLE
If a normal code is displayed during the diagnostic trouble code check but\
the trouble still occurs, check the
circuits for each symptom in the order given in the charts on the following pages and\
proceed to the page
given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1: Electronic Circuit Matrix Chart
Chapter 2: On−Vehicle repair Matrix Chart
Chapter 3: Off−Vehicle repair Matrix Chart
When troubleshooting, check Chapter 1 first. If instructions are given i\
n Chapter 1 to proceed to chapter 2
or 3, proceed as instructed.
(1) If the instruction ”Proceed to next circuit inspection shown on matrix chart” is given in the flow
chart for each circuit, proceed to the circuit with the next highest number in the table to cont\
inue
the check.
(2) If the trouble still occurs even though there are no abnormalities in any\
of the other circuits, then check and replace the ECM.
Chapter 1: Electronic Circuit Matrix Chart
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion6. On−vehicle repair matrix chart
7. Off −vehicle repair matrix chart−
−
Vehicle does not move in a particular position or positions1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No up− shift (1st → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up −shift (2nd → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Park/neutral position switch circuit
7. Off −vehicle repair matrix chart
8. ECMDI−157 DI−35
DI−87
DI−166 −
DI−169 −
DI−145
No up− shift (3rd → O/D)
1. O/D main switck& O/D OFF indicator light circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Throttle position sensor circuit
6. Park/neutral position switch circuit
7. O/D cancel signal circuit
8. Engine coolant temp. sensor circuit
9. On−vehicle repair matrix chart
10.Off −vehicle repair matrix chart
11. ECMDI−174
DI−157 DI−87
DI−166 DI−35
DI−169
DI−172 DI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−148
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
No down−
shift (O/D → 3rd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. ECMDI−157 DI−35
DI−87
DI−166 −
DI−145
No down −shift (3rd → 2nd)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. ECMDI−157 DI−35
DI−87
DI−166 −
DI−145
No down −shift (2nd → 1st)
1. Shift solenoid valve No. 1 and No. 2 circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On−vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−157 DI−35
DI−87
DI−166 −
−
DI−145
Lock− up does not engage
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Stop light switch circuit
6. Park/neutral position switch circuit
7. Engine coolant temp. sensor circuit
8. On −vehicle repair matrix chart
9. Off −vehicle repair matrix chart
10.ECMDI−163
DI−35
DI−87
DI−166
DI−185
DI−169 DI−30 −
−
DI−145
Lock− up does not disengage
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. Stop light switch circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chart
8. ECMDI−163 DI−35
DI−87
DI−166
DI−185 −
−
DI−145
Shift point too high or too low
1. Throttle position sensor circuit
2. Pattern select switch circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. ECMDI−35
DI−179 DI−87
DI−166
DI−145
Up− shifts to 2nd while in L position
Up− shifts to 3rd while in L position1. Park/neutral position switch circuit
2. ECMDI−169
DI−145
Up− shifts to O/D from 3rd while O/D main switch is OFF1. O/D main switck& O/D OFF indicator light circuit
2. ECMDI−174
DI−145
Up−shift to O/D from 3rd while engine is cold
1. Engine coolant temp. sensor circuit
2. On −vehicle repair matrix chart
3. Off −vehicle repair matrix chart
4. ECMDI−30 −
−
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−149
1996 LAND CRUISER (RM451U)
Harsh engagement (N
→ D)
1. Shift solenoid valve SL circuit
2. ATF temp. sensor circuit
3. Throttle position sensor circuit
4. Park/neutral position switch circuit
5. On −vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−163
DI−154 DI−35
DI−169 −
−
DI−145
Harsh engagement (Lock −up)
1. Shift solenoid valve SL circuit
2. Throttle position sensor circuit
3. No. 1 vehicle speed sensor circuit
4. No. 2 vehicle speed sensor circuit
5. On −vehicle repair matrix chart
6. Off −vehicle repair matrix chart
7. ECMDI−163 DI−35
DI−87
DI−166 −
−
DI−145
Harsh engagement (Any driving position)
1. Shift solenoid valve SL circuit
2. ATF temp. sensor circuit
3. Throttle position sensor circuit
4. No. 1 vehicle speed sensor circuit
5. No. 2 vehicle speed sensor circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chart
8. ECMDI−163
DI−154 DI−35
DI−87
DI−166
−
−
DI−145
Slip or shudder (Forward and reverse)1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
Slip or shudder (A particular position)1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
No engine braking1. On −vehicle repair matrix chart
2. Off −vehicle repair matrix chart−
−
Poor acceleration
1. Throttle position sensor circuit
2. No. 1 vehicle speed sensor circuit
3. No. 2 vehicle speed sensor circuit
4. Shift solenoid valve No. 1 and No. 2 circuit
5. Shift solenoid valve SL circuit
6. On −vehicle repair matrix chart
7. Off −vehicle repair matrix chartDI−35
DI−87
DI−166
DI−157
DI−163 −
−
No kick− down
1. Throttle position sensor circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. No. 1 vehicle speed sensor circuit
4. On−vehicle repair matrix chart
5. ECMDI−35
DI−157 DI−87 −
DI−145
No pattern select1. Pattern select switch circuit
2. ECMDI−179
DI−145
No 2nd start
1. Pattern select switch circuit
2. Shift solenoid valve No. 1 and No. 2 circuit
3. ECMDI−179
DI−157
DI−145
Large shift shock or engine stalls when starting off or stopping
1. Shift solenoid valve SL circuit
2. Stop light switch circuit
3. Off −vehicle repair matrix chart
4. ECMDI−163
DI−185 −
DI−145
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−150
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
Chapter 2: On−Vehicle Repair
(  : A340F, A343F Automatic Transmission Repair Manual Pub. No. RM479U)
SymptomSuspect AreaSee page
Vehicle does not move in any forward position and reverse posi-
tion
1. Throttle cable
2. Transmission control rod
3. Manual valve
4. Primary regulator valve
5. Parking lock pawl
6. Off−vehicle repair matrix chartDI−131
DI−131


−
Vehicle does not move in R position1. Off −vehicle repair matrix chart−
Vehicle does not move in a particular position or positions
(Except R position)1. Off −vehicle repair matrix chart−
No up− shift (1st → 2nd)1. 1 −2 shift valve
2. Off −vehicle repair matrix chart
−
No up −shift (2nd → 3rd)1. 2−3 shift valve
2. Off −vehicle repair matrix chart
−
No up− shift (3rd → O/D)1. 3−4 shift valve
2. Off −vehicle repair matrix chart
−
No down− shift (O/D → 3rd)1. 3−4 shift valve
No down −shift (3rd → 2nd)1. 2−3 shift valve
No down −shift (2nd → 1st)1. 1−2 shift valve
2. Off −vehicle repair matrix chart
−
Lock− up does not engage or lock −up does not disengage1. Lock− up relay valve
2. Off −vehicle repair matrix chart
−
Harsh engagement (N → D)1. Accumulator control valve
2. Off −vehicle repair matrix chart
−
Harsh engagement (Lock −up)1. Lock− up control valve
2. Off −vehicle repair matrix chart
−
Harsh engagement (N → R)
1. Accumulator control valve
2. C
2 accumulator
3. Off −vehicle repair matrix chart


−
Harsh engagement (N → L)1. Low coast modulator valve
Harsh engagement (1st → 2nd (D position))1. Accumulator control valve
2. B
2 accumulator


Harsh engagement (1st
→ 2nd (2 position))1. Accumulator control valve
2. B
2 accumulator


Harsh engagement (2nd
→ 3rd → O/D)1. Cut− back valve
Harsh engagement (1st → 2nd → 3rd → O/D)1. Throttle valve
2. Accumulator control valve

Harsh engagement (2nd → 3rd)
3. Accumulator control valve
1. C
2 accumulator
2. Off −vehicle repair matrix chart


−
Harsh engagement (3rd → O/D)
1. Accumulator control valve
2. B
0 accumulator
3. Off −vehicle repair matrix chart


−
Harsh engagement (O/D → 3rd)
1. Accumulator control valve
2. C
0 accumulator
3. Off −vehicle repair matrix chart


−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07352 AT5605D00084
Rotor
No. 2 Vehicle Speed Sensor Rotor
No. 2 Vehicle Speed Sensor
AT8761
5 V/div.
0 V
2 msec./div.
DI−166
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P1700 Speed Sensor No. 2 Circuit Malfunction
(No. 2 Vehicle Speed Sensor)
CIRCUIT DESCRIPTION
The No. 2 vehicle speed sensor detects the rotation speed of the transmissi\
on output shaft and sends sig-
nals to the ECM. The ECM determines the vehicle speed based on these signals\
.
An AC voltage is generated in the No. 2 vehicle speed sensor coil as the r\
otor mounted on the output shaft
rotates, and this voltage is sent to the ECM.
The gear shift point and lock −up timing are controlled by the ECM based on the signals from this vehic\
le
speed sensor and the throttle position sensor signal.
If the No. 2 vehicle speed sensor malfunctions, the ECM uses input signa\
ls from the No. 1 vehicle speed
sensor as a back −up signal.
DTC No.DTC Detecting ConditionTrouble Area
P1700
All conditions below are detected 500 times or more continu-
ously (2 trip detection logic)
(a) No signal from No. 2 vehicle speed sensor is input to ECM while 4 pulses of No. 1 vehicle speed sensor signal is sent
(b) Vehicle speed: 9 km/h (5.6 mph) or more for as least 4 sec.
(c) Park/neutral position switch: OFF (Other than P or N posi-
tion)
(d) Transfer position: Other than N position
 Open or short in No. 2 vehicle speed sensor circuit
 No. 2 vehicle speed sensor
 ECM
Reference:
Waveform between terminals SP2
+ and SP2− when the vehicle
speed is approx. 60 km/h (37 mph).
DI5KW−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010