
Care of Your Cassette  Tape Player 
A tape player  that is not  cleaned regularly can cause 
reduced  sound  quality,  ruined cassettes or a damaged 
mechanism.  Cassette tapes should be  stored  in their 
cases  away from contaminants, direct sunlight  and 
extreme heat. 
If they  aren’t,  they  may  not  operate 
properly  or may  cause  failure  of the  tape  player. 
Your  tape player  should be cleaned regularly after every 
50 hours of use.  Your  radio  may display  CLN  to  indicate 
that  you  have used  your  tape player  for 
50 hours  without 
resetting the tape clean  timer. If  you  notice  a reduction 
in  sound  quality, 
try a  known  good .cassette to  see if the 
tape  or the tape  player is at  fault.  If this other cassette 
has  no  improvement  in sound  quality,  clean the 
tape  player. 
Cleaning  may be done  with a scrubbing action, 
non-abrasive cleaning cassette  with  pads  which  scrub. 
the tape  head as the  hubs  of the  cleaner cassette turn. It 
is  normal  for the cassette  to eject while cleaning. Insert 
the cassette at least three times  to ensure thorough 
cleaning. 
A scrubbing  action cleaning cassette  is 
available through  your Oldsmobile retailer.  You  may 
also choose  a.non-scrubbing  action, wet-type 
cleaner  which  uses  a cassette with a fabric  belt  to clean 
the tape  head. This type  of cleaning cassette  will  not 
eject.  It may  not  clean as  thoroughly  as  the scrubbing 
type  cleaner. 
Cassettes are subject  to  wear  and the sound  quality  may 
degrade  over  time.  Always  make  sure that  the  cassette 
tape is  in  good  condition before  you have  your tape 
player  serviced. 
Care of Your  Compact  Discs 
Handle discs  carefully. Store them  in  their original cases 
or  other  protective cases  and  away from direct sunlight 
and  dust.  If the  surface  of a disc  is soiled,  dampen a 
clean, soft cloth  in a mild,  neutral  detergent  solution and 
clean it,  wiping from the center  to the edge. 
Be sure  never  to  touch  the signal surface  when handling 
discs.  Pick  up  discs by grasping  the outer  edges or the 
edge  of the hole  and the outer edge. 
  

Using  Foam-Type  Cleaner  on  Fabric 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
10. 
11. Vacuum 
and brush  the area to remove  any 
loose  dirt. 
Always  clean a whole  trim  panel or section.  Mask 
surrounding trim along stitch  or  welt lines. 
Mix  Multi-Purpose  Powdered Cleaner following 
the  directionson  the  container label. 
Use  suds  only  and  apply with a clean  sponge. 
Don’t  saturate the  material. 
Don’t  rub it  roughly. 
As soon  as you’ve cleaned the section, use a  sponge 
to remove the  suds. 
Rinse the section  with a clean,  wet sponge. 
Wipe 
off what’s  left with  a slightly damp  paper 
towel or  cloth. 
Then  dry it immediately  with a blow  dryer. 
Wipe  with  a clean cloth. 
I 
Using Solvent-Qpe  Cleaner  on  Fabric 
First, see if  you have to use solvent-type cleaner  at all. 
Some spots  and stains  will clean 
off better  with just 
water‘  and  mild  soap. 
lr you  need  to  use  a solvent: 
0 
0 
Gently  scrape excess  soil  from the  trim  material  with 
a clean, dull knife  or  scraper.  Use  very  little cleaner, 
light pressure  and clean cloths (preferably 
cheesecloth). Cleaning  should start at the outside  of 
the  stain, “feathering”  toward the center.  Keep 
changing  to a clean section 
of the cloth. 
When  you  clean  a stain 
from fabric,  immediately  dry  the 
area  with  a blow  dryer  to  help  prevent  a cleaning  ring. 
6-51  

Special  Cleaning  Problems 
Greasy  or  Oily  Stains 
Stains  caused  by  grease,  oil,  butter,  margarine,  shoe 
polish,  coffee  with  cream,  chewing  gum,  cosmetic  creams,  vegetable  oils,  wax  crayon,  tar  and  asphalt  can 
be  removed  as  follows: 
1. Carefully  scrape  off  excess  stain. 
2. Follow  the  solvent-type  instructions  described  earlier. 
3. Shoe  polish,  wax  crayon, tar and  asphalt  will  stain  if 
left  on  a  vehicle’s  seat  fabric.  They  should  be  removed  as  soon  as  possible.  Be careful,  because  the  cleaner 
will  dissolve  them  and  may  cause  them  to  spread. 
Non-Greasy  Stains 
Stains  caused  by catsup,  coffee  (black),  egg,  hit, fruit 
juice, 
milk, soft  drinks,  wine,  vomit,  .urine  and  blood  can 
be  removed  as  follows: 
1. Carefully  scrape  off  excess  stain,  then  sponge  the 
soiled  area  with  cool  water. 
2. If  a  stain  remains,  follow  the  foam-type  instructions 
described  earlier. 
3. If  an  odor  lingers  after  cleaning  vomit  or  urine, 
treat  the  area  with  a  waterhaking soda  solution: 
1 teaspoon (5 ml)  of  baking  soda  to 1 cup (250 ml) 
of  lukewarm  water. 
4. If  needed,  clean  lightly  with  solvent-type  cleaner. 
Combination  Stains 
Stainscaused  by  candy, ice cream,  mayonnaise,  chili 
sauce  and  unknown  stains  can  be  removed  as  follows: 
Carefully  scrape  off  excess  stain,  then  clean  with 
If  a  stain  remains,  clean  it with  solvent-type  cleaner. 
cool  water  and  allow 
to 
dry. 
6-52  

Capacities  and  Specifications 
Automatic  Transaxle 
Pan Removal and Replacement .... 7 quarts (6.7  L) 
After  Complete Overhaul ....... 10 quarts (9.5  L) 
When  draining  transaxle  convertel;  more and/or  less 
converter  fluid may  be  needed. 
Cooling  System  Including  Reservoir 
3.1L (Code M) ............ 11.6 quarts (10.93 L) 
3.4L (Code X) ............. 12.3 quarts (11.65  L) 
Refrigerant  (R-  I34a), 
Air  Conditioning* 
............. 2.0 pounds (0.91 kg) 
Engine  Specifications 
Type ................................. 
Displacement .......................... 
Compression  Ratio ..................... 
Firingorder .......................... 
Thermostat Temperature ................. 
Valve  Arrangement ..................... 
Horsepower ........................... 
Engine  Crankcase -- Oil and  Filter  Change 
3.1L  L82 (Code M) ........... 4.5 quarts (4.2  L) 
3.4L  LQ1 
(Code X) ........... 5.5 quarts (5.2 L) 
Fuel  Tank ................. 17.1 gallons (64.7 L) 
*See  “Air Conditioning  Refrigerants”  later  in  this  section. 
3.1L  (Code M) 
V6 
191 CID (3.1L) 
9.6:  1 
1-2-3-4-5-6 
195°F (91°C) 
In-Head 
160 @ 5200 
3.4L  (Code X) 
V6 
207 
CID (3.4L) 
9.25:  1 
1-2-3-4-5-6 
195°F (91 “C) 
In-Head 
215 @ 5200 
6-69  

Vehicle  Dimensions Normal  Maintenance  Replacement  Parts 
Wheelbase ............. 107.5”  (2730 inm) 
Tread  Width 
Front 
................. 59.5”(1512 mm) 
Rear .................. 58.0” (1472 mm) 
Overall  Length Coupe 
............... 193.9”  (4926 mm) 
Sedan ................ 193.7”  (492  1 mm) 
Overall  Width ............ 7 1 .O” ( 1804 mm) 
Overall  Height 
Coupe 
................ 53.3” (1 353 mm) 
Sedan.. ............... 54.8”(1391  mm) 
Air  Conditioning  Refrigerants 
Not  all air conditioning  refrigerants are the  same. 
If 
the air  conditioning  system  in  your  vehicle  needs 
refrigerant,  be sure  the  proper  refrigerant is  used. 
If  you’re  not  sure, ask  your  Oldsmobile  retailer. 
Air  Cleaner  Filter 
Battery 
All  Engines ......................... A1208C 
3.1L  (Code 
M) ...................... 525  CCA 
3.4L (Code 
X) ...................... 690  CCA 
Engine  Oil  Filter 
3.1L  (Code M) ........................ PF47 
3.4L(CodeX) 
......................... PF51 
3.1L  (Code 
M) ..................... CV892C 
3.4L  (Code  X) 
.......... : ........... CV895C 
All  Engines 
........................... RC27 
3.1L  (Code 
M) ............... AC.  Type  41-940 
Gap: 
0.060” (1.52 mm) 
3.4L  (Code  X) ................ AC  Type  41-919 
Gap:  0.045”  (1.14 
mm) 
Length ........................ 20” (510 mm) 
Type 
...................................p in 
PCV  Valve  
Radiator  Cap 
Spark  Plugs 
Windshield  Wiper  Blade  Replacement 
6-70