1996 LAND ROVER DEFENDER gearbox

ELECTRICAL
5
REPAIR PASSIVE COIL
Service repair no - 86.77.35
Remove
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery negative lead.
NOTE: Operation 6 needs to be carried out
within 15 seconds to avoid activating
battery backed-up alarm sounder, if fitted.
7.Remove steering wheel
See STEERING,
Repair, Steering wheel.
8.Remove 4 screws securing instrument panel to
fascia cowl
See INSTRUMENTS, Repair,
Instrument panel.
9.Pull instrument panel away from fascia and
disconnect speedometer cable, multi-plugs,
alarm LED plug lead, heated rear screen lead,
gearbox oil temperature lead and immobiliser
warning light leads.
10.Remove instrument panel.
11.Remove 7 screws securing upper and lower
halves of nacelle to steering column mounting
bracket
See STEERING, Repair, Steering
column nacelle.
12.Release multi-switch gaiters from both sides of
nacelle.
13.Remove nacelle upper and lower halves from
steering column; collect blanking grommet from
RH side.
14.Disconnect multi-plug and remove passive coil
from starter switch.
Refit
15.Feed passive coil plug lead into fascia cowl area
and reconnect multi-plug .
16.Fit coil on starter switch.
17.Position nacelle upper and lower halves to
steering column mounting bracket and secure
with 7 screws. Do not fully tighten screws at this
stage
See STEERING, Repair, Steering
column nacelle.
18.Check that passive coil is still fitted correctly on
starter switch.
19.Check fit of nacelle at starter switch and steering
column and fully tighten fixing screws.
20.Fit multi-switch gaiters to both sides of nacelle
and check that blanking grommet is located.
21.Position instrument panel to fascia cowl area
and reconnect immobiliser warning light leads,
gearbox oil temperature lead, heated rear screen
lead, alarm LED plug lead, main harness multi-
plugs and speedometer.
22.Secure instrument panel to fascia cowl with 4
screws
See INSTRUMENTS, Repair,
Instrument panel.
23.Fit steering wheelSee STEERING, Repair,
Steering wheel.
24.Reconnect battery negative lead.
25.Fit battery access cover.
26.Fit LH seat cushion.
27.Test immobilisation and alarm system.

86ELECTRICAL
10
REPAIR Refit
12.Fit alarm indicator light into fascia panel and
reconnect plug lead.
13.Reconnect speedometer cable and fit instrument
panel to fascia cowl.
14.Fit steering wheel
See STEERING, Repair,
Steering wheel.
15.Reconnect battery negative lead.
16.Fit battery access cover.
17.Fit LH seat cushion.ALARM SYSTEM FUSE
Service repair no - 86.77.04
Remove
1.Remove LH front seat cushion.
2.Release retaining clip and remove battery
access cover.
3.Slacken battery negative lead clamp bolt.
4.Turn starter switch 'on'.
5.Turn starter switch 'off' and remove key.
6.Disconnect battery negative lead.
NOTE: Operation 6 needs to be carried out
within 15 seconds to avoid activating
battery backed-up alarm sounder, if fitted.
NOTE: If an alarm sounder without battery
back-up is fitted, it is not necessary to
disconnect battery.
7.Remove steering wheel
See STEERING,
Repair, Steering wheel.
8.Remove 4 screws securing instrument panel to
fascia cowl
See INSTRUMENTS, Repair,
Instrument panel.
9.Pull instrument panel away from fascia and
disconnect speedometer cable, main harness
multi-plugs, alarm LED plug lead, heated rear
screen leads, gearbox oil temperature lead and
immobiliser warning light lead.
10.Remove instrument panel.
11.Remove alarm system 15 amp (blue) fuse from
holder located behind starter switch.

ELECTRICAL
11
REPAIR REV: 05/99 Refit
12.Fit new fuse.
13.Position instrument panel to fascia cowl area
and reconnect immobiliser warning light leads,
gearbox oil temperature lead, heated rear screen
leads, alarm LED plug lead, main harness
multi-plugs and speedometer cable,
14.Secure instrument panel to fascia cowl with 4
screws
See INSTRUMENTS, Repair,
Instrument panel.
15.Fit steering wheelSee STEERING, Repair,
Steering wheel.
16.Reconnect battery negative lead.
17.Fit battery access cover.
18.Fit LH front seat cushion.GENERATOR
Service repair no - 86.10.02
Remove
1.Disconnect battery.
2.Remove drive belt
See Auxiliary drive belt.
3.Unscrew 3 fixings, remove heat shield from rear
of generator, and disconnect electrical leads
from generator.
4.Remove generator bottom fixing bolt.
5.Remove long through bolt from top fixing and lift
generator from engine.
Refit
6.Fit generator to engine mounting bracket and
secure with top and bottom fixing bolts.
7.Connect electrical leads.
8.Fit heat shield.
9.Fit drive belt
See Auxiliary drive belt; Refit.
10.Reconnect battery.

86ELECTRICAL
18
REPAIR REVERSE LAMP SWITCH
Service repair no - 37.27.01
Remove
The reverse lamp switch is located on the LH side of
the gearbox extension housing and is accessible from
underneath the vehicle.
1.Place vehicle on suitable ramp.
2.Disconnect reverse lamp switch lead multi-plug
from harness connector.
3.Unscrew switch from extension housing.
Refit
4.Fit new switch to gearbox extension housing.
Tighten to
25 Nm (18 lbf/ft).
5.Fit lamp switch lead multi-plug to harness
connector.
6.Check operation of lamp switch.WARNING LAMP ASSEMBLY
Service repair no - 86.45.60 - Warning lamp
assembly
Service repair no - 86.45.61 - Warning lamp bulb
renewal
Remove
1.Disconnect battery.
2.Remove 2 screws and withdraw warning light
assembly from instrument panel.
3.Remove multi-plug to give access to warning
lamp bulbs.
4.Twist bulb holder and pull it from its socket.
5.Pull bulb from holder.
Refit
6.Fit new bulb and refit holder.
7.Fit multi-plug.
8.Fit warning lamp assembly to instrument panel
9.Reconnect battery.