1996 LAND ROVER DEFENDER AUX

STEERING
7
REPAIR POWER STEERING PUMP
Service repair no - 57.20.14
Remove
NOTE: A chassis undertray may be fitted
on some vehicle derivatives to conform to
legal requirements. When under chassis
remove and refit procedures are required, it may
be necessary to remove the undertray
See
CHASSIS AND BODY, Repair, Front undertray
.
1.Disconnect battery.
2.Remove viscous fan unit
See COOLING
SYSTEM, Repair, Viscous coupling and fan
.
3.Restrain steering pump pulley, slacken but do
not remove 3 bolts securing pulley.
4.Remove drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
5.Remove bolts and remove pulley.
6.Position suitable container beneath steering
pump.
7.Slacken retaining clip and disconnect return
hose from steering pump.
8.Disconnect high pressure pipe from steering
pump.
9.Allow steering fluid to drain into container.
CAUTION: Plug all connections to prevent
ingress of dirt.
10.Remove 4 bolts securing steering pump bracket
to engine auxiliary mounting bracket.
11.Remove pump and bracket assembly.
12.Remove 3 bolts and detach mounting bracket
from pump.
Refit
13.Fit mounting bracket to replacement steering
pump. Tighten bolts to
9 Nm (7 lbf/ft).
14.Fit pump and bracket to auxiliary mounting
bracket. Tighten bolts to
35 Nm (26 lbf/ft).
15.Connect high pressure feed pipe to steering
pump and tighten to
20 Nm (15 lbf/ft).
16.Connect return hose to steering pump. Tighten
retaining clip to
3 Nm (2 lbf/ft).
17.Position pulley to steering pump, coat threads of
bolts with Loctite 242; fit but do not fully tighten
bolts.
18.Fit drive belt
See ELECTRICAL, Repair,
Auxiliary drive belt
.
19.Restrain steering pump pulley, tighten bolts to
10
Nm (7lbf/ft).
20.Fit viscous fan unitSee COOLING SYSTEM,
Repair, Viscous coupling and fan
.
21.Bleed power steering system
See Power
steering system - bleed
.
POWER STEERING PUMP DRIVE BELT
Service repair no - 57.20.02
NOTE: For details of drive belt remove and
refit
See ELECTRICAL, Repair, Auxiliary
drive belt
.

CHASSIS AND BODY
35
REPAIR REV: 05/99
15.If fitted, remove 2 screws, washers and nuts
securing auxiliary switch panel to lower fascia
panel and switch cover.
16.Withdraw switch panel and disconnect switch
leads.
17.Remove 2 screws securing switch cover to
parcel tray.
18.Remove fuse box cover.
19. Models with hand throttle:
Remove fuse box LH retaining screw.
Pivot fuse box down to gain access to lower
inner hand throttle cover fixing screw.
Remove 4 screws and lift up hand throttle cover
from lower fascia panel.
20.Remove 2 screws and remove both footwell
vents from lower fascia panel.
21.Remove single screw and detach door check
strap cover from LH and RH doors.
22.Remove 3 screws securing wiper motor cover to
fascia bulkhead.
23.Release locating pins from fascia panel, lower
wiper motor cover and, if applicable, disconnect
radio speaker leads. Retain wiper motor rack
cover. On LH drive vehicles, disconnect
multi-plugs from rear of switch panel.
24.Prise out 2 large and 5 small cap fasteners
securing trim panel to parcel shelf and fascia
bulkhead.
25.Carefully fold back trim panel to clear fresh air
vent operating levers and remove panel from
parcel shelf.

76CHASSIS AND BODY
36
REPAIRREV: 05/99 26.Release demist hose and lift parcel shelf from
lower fascia panel (heater duct). Feed main
harness leads and plugs through aperture in
parcel shelf.
27.Remove parcel shelf.
28.Remove 7 screws securing bottom edge of lower
fascia panel to fascia bulkhead, noting position
of both footwell cover retaining plates.
29.Remove both retaining plates and lower footwell
covers.
30.Unscrew 2 retaining bolts securing top edge of
lower fascia panel to bulkhead.
31.With assistance, lower fascia panel and, if
applicable, disconnect RH radio speaker leads.
32.Remove fascia panel from vehicle.Refit
33.Position lower fascia panel to bulkhead,
reconnect RH speaker leads, if applicable, and
secure top edge with 2 bolts.
34.Locate RH footwell cover retaining plate under
bottom edge of fascia panel and secure with 3
screws.
35.Repeat operation for LH footwell cover retaining
plate.
36.Fit remaining lower fascia panel fixing screws.
37.Locate parcel shelf. Ensure all radio and
auxiliary switch panel harness leads and plugs
are fed through aperture in parcel shelf.
38.Fit demist hoses into heater duct of lower fascia
panel. Ensure flanges of hose grommets are
correctly seated.
39.Fit trim panel and secure with cap fasteners.
40.Reconnect LH speaker leads, if applicable,
locate wiper motor cover pins in lower fascia
panel and secure wth 3 screws. Ensure wiper
rack cover is correctly seated. On LH drive
vehicles, reconnect multi-plugs to rear of switch
panel.
41.Secure finisher to wiper motor cover.
42.Fit door check strap covers on both sides.
43.Fit footwell vents to lower fascia panel.
44. Models fitted with hand throttle:
Fit hand throttle cover.
Secure LH side of fuse box.
45.Fit fuse box cover.
46.Fit auxiliary switch cover to parcel tray, if
applicable.

CHASSIS AND BODY
37
REPAIR REV: 05/9947.Connect leads and plugs to auxiliary switches
and clock.
48.Secure switch panel to lower fascia panel and
switch cover.
49.Position radio housing, if applicable, and feed
radio multi- plug, aerial and speaker leads from
switch cover to radio housing.
50.Secure radio housing to trim panel.
51.Fit radio connections and secure radio in
housing.
52.Fit crash pad to fascia bulkhead.
53.Fit demister vents in crash pad.
54.Fit grab handle to lower fascia panel and secure
to crash pad. Refit Land Rover decal.
55.Connect multi-plugs to rear screen, hazard and
interior lamp switches and fit switch panel to
fascia panel.
56.Fit heater control cable
See HEATING AND
VENTILATION, Repair, Heater control cable -
air distribution
.
57.Fit instrument panel
See INSTRUMENTS,
Repair, instrument panel
.
58.Fit steering column nacelle
See STEERING,
Repair, Steering column nacelle
.
59.Fit steering wheel
See STEERING, Repair,
Steering wheel
.
60.Reconnect battery.FRONT UNDERTRAY
Service repair no - 76.11.81 - Front undertray
Service repair no - 76.11.85 - Acoustic pad
Remove
1.Raise vehicle on ramp.
2.Position support under chassis front
crossmember.
3.Lower ramp to give clearance between axle and
undertray.
4.Remove 4 nuts, disconnect propeller shaft from
front axle, and move aside.
5.Remove 2 bolts securing undertray to chassis
front crossmember.
6.Remove nut securing undertray to bump stop
front fixing bolt on both sides.
7.Remove 2 bolts securing sides of undertray to
rear undertray.
8.Pull front undertray forwards to release flanges
from rear undertray.
9.Lower undertray to clear steering box etc. and
manouvre rearwards over axle.
10.Remove front undertray.
11.If necessary, remove 8 fasteners to release
acoustic pad from undertray.

82AIR CONDITIONING
2
REPAIR COMPRESSOR DRIVE BELT
Service repair no - 82.10.02
Remove
1.Disconnect battery.
2.Remove auxiliary drive belt
See ELECTRICAL,
Repair, Auxiliary drive belt.
3.Remove 3 nuts securing drive belt guard to
compressor retaining studs.
4.Slacken 3 belt tensioner retaining bolts.
5.Remove compressor drive belt. Mark direction
on belt if refitting.Refit
6.Fit compressor drive belt.
7.Fit drive belt guard.
8.Fit torque meter to centre of tensioner, apply and
hold a torque of
35 Nm (26 lbf/ft).
9.Tighten tensioner retaining bolts.
10.Rotate crankshaft 2 full turns.
11.Reapply and hold a torque of
35 Nm (26 lbf/ft)
to tensioner, then fully slacken and retighten
tensioner retaining bolts to
25 Nm (18 lbf/ft).
12.Fit auxiliary drive beltSee ELECTRICAL,
Repair, Auxiliary drive belt.
13.Reconnect battery.

ELECTRICAL
11
REPAIR REV: 05/99 Refit
12.Fit new fuse.
13.Position instrument panel to fascia cowl area
and reconnect immobiliser warning light leads,
gearbox oil temperature lead, heated rear screen
leads, alarm LED plug lead, main harness
multi-plugs and speedometer cable,
14.Secure instrument panel to fascia cowl with 4
screws
See INSTRUMENTS, Repair,
Instrument panel.
15.Fit steering wheelSee STEERING, Repair,
Steering wheel.
16.Reconnect battery negative lead.
17.Fit battery access cover.
18.Fit LH front seat cushion.GENERATOR
Service repair no - 86.10.02
Remove
1.Disconnect battery.
2.Remove drive belt
See Auxiliary drive belt.
3.Unscrew 3 fixings, remove heat shield from rear
of generator, and disconnect electrical leads
from generator.
4.Remove generator bottom fixing bolt.
5.Remove long through bolt from top fixing and lift
generator from engine.
Refit
6.Fit generator to engine mounting bracket and
secure with top and bottom fixing bolts.
7.Connect electrical leads.
8.Fit heat shield.
9.Fit drive belt
See Auxiliary drive belt; Refit.
10.Reconnect battery.

86ELECTRICAL
12
REPAIR AUXILIARY DRIVE BELT
Service repair no - 86.10.03
NOTE: If cast lines on tensioner arm and
tensioner spring case are aligned, a new
drive belt must be fitted.
Remove
1.Disconnect battery.
2.Remove fan cowl
See COOLING SYSTEM,
Repair, Fan cowl.
3.Apply ring spanner to tensioner pulley retaining
bolt.
4.Turn spanner to release pulley tension from belt.
5.Detach belt from pulley.
6.Release tensioner.
7.Complete removal of belt. Mark direction on belt
if refitting.
Refit
8.Using ring spanner, release pulley tensioner and
fit new drive belt.
9.Remove ring spanner, drive belt will
automatically tension.
10.Fit fan cowl
See COOLING SYSTEM, Repair,
Fan cowl.
STARTER MOTOR
Service repair no - 86.60.01
Remove
1.Disconnect battery.
2.Disconnect electrical leads from starter solenoid.
3.Remove 3 fixings securing starter motor to
flywheel housing.
4.Withdraw starter motor.
Refit
5.Locate starter motor and secure to flywheel
housing.
6.Reconnect electrical leads to starter solenoid.
7.Reconnect battery.