Page 215 of 298
![FORD PROBE 1996 2.G Owners Manual 218
*
[SV13670(ALL)01/95]
Neveruse:
*
[SV13680(ALL)01/95]
q
ªNon-Detergentº oils
*
[SV13690(ALL)04/95]
q
Oils labeled API SA, SB, SC, SD, SE, SF or SG
%*
[SV13700(ALL)01/95]
q
Additional engine oil FORD PROBE 1996 2.G Owners Manual 218
*
[SV13670(ALL)01/95]
Neveruse:
*
[SV13680(ALL)01/95]
q
ªNon-Detergentº oils
*
[SV13690(ALL)04/95]
q
Oils labeled API SA, SB, SC, SD, SE, SF or SG
%*
[SV13700(ALL)01/95]
q
Additional engine oil](/manual-img/11/5320/w960_5320-214.png)
218
*
[SV13670(ALL)01/95]
Neveruse:
*
[SV13680(ALL)01/95]
q
ªNon-Detergentº oils
*
[SV13690(ALL)04/95]
q
Oils labeled API SA, SB, SC, SD, SE, SF or SG
%*
[SV13700(ALL)01/95]
q
Additional engine oil additives, oil treatments
or engine treatments
*
[SV13725(ALL)04/95]
Engine oils with anSAE 5W-30viscosity are
PREFERREDfor your vehicle. They provide the
best engine performance, fuel economy and
engine protection for all climates down to-15ÊF
(-25ÊC).
%*
[SV13750(ALL)03/95]
Synthetic engine oils which are CERTIFIED and
of the preferred viscosity may be used in your
engine. The engine oil and oil filter must still be
changed according to the maintenance schedule.
*
[SV13775(ALL)01/95]
Checking and Adding Engine Oil
*
[SV13800(ALL)03/95]
Since the proper amount of engine oil is
important for safe engine operation, check the oil
using the dipstick each time you put fuel in
your vehicle. Remember the engine must be off,
the oil must be warm and the vehicle must be
parked on level ground.
*
[SV13900(ALL)04/95]
Checking the engine oil level:
*
[SV14000(ALL)02/95]
1. Turn the engine off after it has warmed up
and allow a few minutes for the engine oil
to drain back into the oil pan.
*
[SV14050(ALL)05/94]
2. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park) (automatic transaxle) or 1 (First)
(manual transaxle).
*
[SV14100(ALL)02/95]
3. Open the hood. Protect yourself from engine
heat.
*
[SV14200(ALL)03/95]
4. Locate the engine oil dipstick (highlighted in
yellow) and carefully pull it out of the
engine.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 216 of 298
![FORD PROBE 1996 2.G Owners Manual 219
*
[SV14300(ALL)01/95]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
[SV14400(ALL)01/93]
one inch art:0032075-A
Engine oil dipstick
[SV14500(ALL)05/95]
6 FORD PROBE 1996 2.G Owners Manual 219
*
[SV14300(ALL)01/95]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
[SV14400(ALL)01/93]
one inch art:0032075-A
Engine oil dipstick
[SV14500(ALL)05/95]
6](/manual-img/11/5320/w960_5320-215.png)
219
*
[SV14300(ALL)01/95]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
[SV14400(ALL)01/93]
one inch art:0032075-A
Engine oil dipstick
[SV14500(ALL)05/95]
6. Carefully, pull the dipstick out again. If the
oil level is below the L line, add engine oil
as necessary. If the oil level is beyond the
letter F, engine damage or high oil
consumption may occur and some oil must
be removed from the engine.
*
[SV14600(ALL)01/95]
7. Put the dipstick back in and make sure it is
fully seated.
%*
[SV14700(ALL)03/95]
Adding engine oil
*
[SV14800(ALL)01/95]
It may be necessary to add some oil between oil
changes. Make sure you use a CERTIFIED
engine oil of the preferred viscosity. Your
vehicle's warranty coverage may not apply if
engine damage is caused by the use of improper
engine oil.
*
[SV15000(ALL)03/95]
Add engine oil through the oil filler cap
highlighted in yellow. To add oil, remove the
filler cap and use a funnel to pour oil into the
opening. Be careful not to overfill the engine.
Recheck the oil level after you finish adding oil.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 218 of 298
221
*
[SV17400(ALL)03/95]
Engine Coolant
*
[SV17500(ALL)02/95]
Checking the engine coolant
*
[SV17550(ALL)01/95]
NOTE: Be sure to read and understand
Precautions When Servicing Your Vehicle
at the beginning of this chapter.
*
[SV17600(ALL)05/95]
RWARNING
The cooling fan is automatic and may
come on at any time. Always disconnect
the negative terminal of the battery before
working near the fan.
[SV17900(ALL)02/92]
Inspect the coolant level with the dipstick
attached to the reservoir cap. Remove the cap,
wipe it clean and then put it back in the
reservoir. Remove it again. The coolant level
should be between L and F.
[SV17950(ALL)01/92]
If the coolant level is at or below the L line, add
enough 50/50 mixture of specified coolant and
water to bring the level to the F mark.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 219 of 298
222 [SV18200(ALL)01/92]
half page art:0032038-BEngine coolant recovery reservoir and dipstick
*
[SV18500(ALL)01/95]
Adding engine coolant
*
[SV18600(ALL)05/95]
RWARNING
Do not put engine coolant in the container
for the windshield washer fluid.
*
[SV18610(ALL)06/95]
If sprayed to clean the glass, engine coolant or
antifreeze could make it difficult to see through
the windshield.
[SV18650(ALL)02/95]
Add engine coolant only to the recovery
reservoir Ð not to the radiator.If the coolant
level is low, add to the engine coolant recovery
reservoir container a 50/50 mixture of water and
the type of coolant that Ford specifies. Check the
coolant level again the next few times you drive
your vehicle.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 223 of 298
![FORD PROBE 1996 2.G Owners Manual 226 %
*
[SV20600(ALL)01/95]
Use Ford Premium Cooling System Fluid or an
equivalent engine coolant that meets Ford
Specification ESE-M97B44-A. Do not use alcohol
or methanol antifreeze and do not use e FORD PROBE 1996 2.G Owners Manual 226 %
*
[SV20600(ALL)01/95]
Use Ford Premium Cooling System Fluid or an
equivalent engine coolant that meets Ford
Specification ESE-M97B44-A. Do not use alcohol
or methanol antifreeze and do not use e](/manual-img/11/5320/w960_5320-222.png)
226 %
*
[SV20600(ALL)01/95]
Use Ford Premium Cooling System Fluid or an
equivalent engine coolant that meets Ford
Specification ESE-M97B44-A. Do not use alcohol
or methanol antifreeze and do not use engine
coolant mixed with alcohol or methanol
antifreeze. If you do not use the proper coolant,
the aluminum radiator on your vehicle will
corrode.
*
[SV20700(ALL)04/93]
Leave the engine coolant in all year. Make sure
that the coolant will not freeze at the
temperature level in which you drive during
winter months. Keep an engine coolant in your
engine that has a protection rating of at least
-20ÊF (-29ÊC), orwhatever protection rating is
appropriate for the climate in which you live.
*
[SV20800(ALL)03/95]
To find out how much engine coolant mixture
your vehicle's coolant system can hold, seeRefill
capacities for fluidsin the Index.
*
[SV20900(ALL)02/95]
You may add water by itself only in an
emergency, but you should replace it with a
50/50 mixture as soon as possible.
*
[SV21000(ALL)01/95]
Have your dealer check the engine cooling
system for leaks if you have to add a quart
(liter) of engine coolant more than once a month.
*
[SV21200(ALL)05/95]
Engine coolant drain and flush
*
[SV21300(ALL)05/94]
The proper procedures to completely drain and
flush the engine cooling system can be found in
the Service Manual for your vehicle or you can
see your dealer. See the order form located
before this chapter. Follow these recommended
procedures to ensure that your vehicle has the
specified engine level and 50/50 mixture of
cooling system fluid and water.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 224 of 298
![FORD PROBE 1996 2.G Owners Manual 227 [SV21450(ALL)05/95]
Refilling the engine coolant Ð 2.0L engine
*
[SV21500(ALL)03/95]
When the entire engine cooling system is to be
drained and refilled, use the following
procedure:
*
[SV21600(A FORD PROBE 1996 2.G Owners Manual 227 [SV21450(ALL)05/95]
Refilling the engine coolant Ð 2.0L engine
*
[SV21500(ALL)03/95]
When the entire engine cooling system is to be
drained and refilled, use the following
procedure:
*
[SV21600(A](/manual-img/11/5320/w960_5320-223.png)
227 [SV21450(ALL)05/95]
Refilling the engine coolant Ð 2.0L engine
*
[SV21500(ALL)03/95]
When the entire engine cooling system is to be
drained and refilled, use the following
procedure:
*
[SV21600(ALL)01/89]
1. Remove the radiator cap.
*
[SV21700(ALL)06/89]
2. With the engine off and cool, add a 50/50
mixture of recommended engine cooling
system fluid and water until the radiator is
full.
*
[SV21800(ALL)07/93]
3. Replace and fully tighten the radiator cap,
then unscrew the cap to the first stop.
*
[SV21900(ALL)06/89]
4. Start and idle the engine until the radiator
upper hose is warm (this indicates the
thermostat is open and engine coolant is
flowing through the entire system).
[SV22000(ALL)04/95]
5. Shut the engine off and check the fluid level
in the radiator. Add more fluid if necessary.
[SV22005(ALL)03/94]
6. When the radiator is filled to the proper
level, replace the coolant system cap and
tighten both caps completely.
[SV22010(ALL)01/92]
Refilling the engine coolant Ð 2.5L engine
[SV22015(ALL)04/95]
When the entire cooling system is to be drained
and refilled, use the following procedure:
[SV22020(ALL)04/93]
1. Locate the radiator breather cap and the
coolant system cap in your engine
compartment. The cap on your right
(driver's side) is the radiator breather cap.
The cap on your left (passenger's side) is the
coolant system cap.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 226 of 298
![FORD PROBE 1996 2.G Owners Manual 229 [SV22035(ALL)02/92]
4. Replace the radiator breather cap and the
coolant system cap and tighten to the first
stop.
[SV22050(ALL)02/92]
5. Start and idle the engine until the radiator
upper hose is FORD PROBE 1996 2.G Owners Manual 229 [SV22035(ALL)02/92]
4. Replace the radiator breather cap and the
coolant system cap and tighten to the first
stop.
[SV22050(ALL)02/92]
5. Start and idle the engine until the radiator
upper hose is](/manual-img/11/5320/w960_5320-225.png)
229 [SV22035(ALL)02/92]
4. Replace the radiator breather cap and the
coolant system cap and tighten to the first
stop.
[SV22050(ALL)02/92]
5. Start and idle the engine until the radiator
upper hose is warm. The warm hose
indicates the thermostat is open and the
engine coolant is flowing through the entire
system.
[SV22060(ALL)02/92]
6. Shut the engine off and check the fluid level
in the radiator through the coolant system
cap opening. Add more fluid if necessary.
[SV22070(ALL)02/92]
7. When the radiator is filled to the proper
level, replace the coolant system cap and
tighten both caps completely.
%*
[SV22100(ALL)11/94]
Checking hoses
*
[SV22200(ALL)01/89]
Check all engine and heater system hoses and
hose connections for deterioration, leaks, and
loose hose clamps as specified in the
maintenance schedule. Repair or replace with
Motorcraft hoses or equivalent as necessary.
%
*
[SV22300(ALL)03/95]
Windshield Washer Fluid and
Wipers
*
[SV22350(ALL)03/95]
Washer Fluid
[SV22500(ALL)01/95]
Check the level of the windshield washer fluid
every time you stop for fuel. The reservoir for
the windshield washer fluid is located in the
engine compartment. Visual inspection can
determine if the washer fluid is adequate. Do
not operate the washer when the reservoir is
empty.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995
Page 237 of 298
![FORD PROBE 1996 2.G Owners Manual 240soda and water. Reinstall the cables when you
are done cleaning them, and apply a small
quantity of grease to the top of each battery
terminal to help prevent corrosion.
*
[SV29616(ALL)02/95]
Batte FORD PROBE 1996 2.G Owners Manual 240soda and water. Reinstall the cables when you
are done cleaning them, and apply a small
quantity of grease to the top of each battery
terminal to help prevent corrosion.
*
[SV29616(ALL)02/95]
Batte](/manual-img/11/5320/w960_5320-236.png)
240soda and water. Reinstall the cables when you
are done cleaning them, and apply a small
quantity of grease to the top of each battery
terminal to help prevent corrosion.
*
[SV29616(ALL)02/95]
Battery replacement
[SV29620(ALL)11/91]
When the original equipment maintenance-free
battery is replaced under warranty, it may be
replaced by a low-maintenance battery.
[SV29625(ALL)03/95]
The low-maintenance battery has removable vent
caps for checking the electrolyte level and
adding water, if necessary.
[SV29630(ALL)04/93]
The electrolyte level should be checked at least
every 24 months or 24,000 miles (40,000 km) in
temperatures up to90ÊF (32ÊC) andmore in
temperatures above90ÊF (32ÊC).Keep the
electrolyte level in each cell up to the level
indicator. Do not overfill.
[SV29635(ALL)03/95]
If the level gets low, you can add plain tap
water to the battery, provided the water isn't
hard or doesn't have a high mineral or alkali
content. However, if possible, refill with distilled
water. If the battery needs water quite often,
have the charging system checked for a possible
problem.
[SV29636(ALL)01/95]
If you ever disconnect the battery or install a
new battery, you must allow the computer to
ªrelearnº its idle condition before your vehicle
will drive properly. To begin this process, put
the gearshift in P (Park) (automatic transaxle) or
N (Neutral) (manual transaxle), set the
emergency brake, turn off all the accessories, and
start the vehicle. Bring the engine to normal
operating temperature.
File:prsvp.ex
Update:Fri Jun 23 19:33:26 1995