1996 FORD MUSTANG buttons

99
*
[SC11000( ALL)08/95]
If you drive up or down a steep hill, your
vehicle may momentarily slow down or speed
up, even though the speed control is on. This is
normal.
*
[SC11030( ALL)03/95]
NOTE: If your speed increases above your set
speed while driving in D (Drive) on a
downhill grade, you may want to
depress the Transmission Control
Switch located on the shift lever to
turn off overdrive to reduce vehicle
speed. Speed control cannot reduce the
vehicle speed if it goes above your set
speed on a downhill grade.
[SC11045(M )03/95]
NOTE: If your vehicle is equipped with a 5
speed manual transmission, and if your
speed increases above your set speed
while driving in 5 (Fifth) gear on a
downhill grade, you may want to shift
to 4 (Fourth) gear to reduce vehicle
speed. Depressing the clutch pedal
cancels speed control, therefore speed
control must be reset by pressing the
SET/ACCEL or RESUME buttons.
Speed control cannot reduce the vehicle
speed if it goes above your set speed
on a downhill grade.
*
[SC11100( ALL)08/95]
RWARNING
Do not use the speed control in heavy
traffic or on roads that are winding,
slippery, or unpaved.
File:07rcscm.ex
Update:Wed Mar 27 09:30:54 1996

110
%*
[FV08030( ALL)05/95]
Remote Entry System
(If equipped)
*
[FV08036( ALL)03/94]
If your vehicle has the remote entry system, you
can lock and unlock the vehicle doors and open
the trunk without using a key. The remote also
has a personal alarm feature. The buttons for the
system are located on the hand held
transmitter(s) that came with your vehicle.
*
[FV08040( ALL)06/95]
The system will work with up to four
transmitters. Your vehicle came with two
transmitters. Additional transmitters can be
ordered from your dealer.
*
[FV08045(MBC )02/95]
The remote entry features only operate with the
ignition in the OFF position.
[FV08050(MBC )02/95]
one third page art:0001000-A
Remote entry transmitter
%*
[FV08055( ALL)02/95]
Unlocking the doors and opening the trunk
*
[FV08060( ALL)02/95]
To unlock the driver's door, press the UNLOCK
button.
*
[FV08065( ALL)02/95]
To unlock the other doors, press the UNLOCK
button a second time within five seconds of
unlocking the driver's door.
*
[FV08070(MBC )02/95]
To open the trunk, press the TRUNK button.
File:08rcfvm.ex
Update:Wed Mar 27 09:32:34 1996

111
*
[FV08080( ALL)02/95]
Locking the doors
*
[FV08085( ALL)02/95]
To lock all the doors, press the LOCK button.
*
[FV08090(MBC )01/95]
If you would like a signal that the doors are
being locked, press the LOCK button again
within five seconds. The doors will lock again,
the horn will beep and the low beam headlamps
and tail lamps will flash.
%*
[FV08114( ALL)02/95]
Activating the remote personal alarm
*
[FV08120( ALL)02/95]
If you wish to activate the remote personal
alarm, press the PANIC button. This will honk
the horn and flash the low beam headlamps and
tail lamps for approximately two minutes and
forty-five seconds. You can turn it OFF by
pressing the PANIC button again or by turning
the ignition key to the RUN position.
[FV08125( ALL)05/94]
When you use the remote entry UNLOCK,
TRUNK or PANIC buttons, the illuminated entry
system turns on the interior lights for 25
seconds. You can turn these lights off with the
LOCK button or by turning the ignition to the
RUN position. The interior lights will not turn
off if you have turned them on manually or if a
door is open.
%*
[FV08200(M )05/95]
Arming and disarming the alarm system
[FV08300(M )05/95]
If your vehicle is equipped with the optional
factory installed anti-theft system, the remote
entry system will automatically arm it when the
doors are locked with the remote entry LOCK
button. The remote entry UNLOCK button will
disarm or reset a triggered anti-theft alarm.
*
[FV08400(M )05/95]
The remote entry system is designed to work
with the factory installed anti-theft system. It
may not work with other anti-theft systems.
File:08rcfvm.ex
Update:Wed Mar 27 09:32:34 1996

142
% [AS21370(MBC )06/95]
Electronic Stereo Cassette Radio
*
[AS21400(MBC )08/95]
Using the Controls on Your New Radio
*
[AS21500(MBC )08/95]
How to turn the radio on and adjust the
volume
*
[AS22050(MBC )10/95]
Press the ªPOWERº button to turn the radio on.
Press it again to turn it off.
*
[AS22060(MBC )04/94]
Press the right (+) side of the ªVOLUMEº
button to increase the volume. Press the left (s)
side of the button to decrease the volume.
Illuminated bars in the display show the relative
volume level.
*
[AS22070(MBC )10/95]
NOTE: If the volume level is set above a
certain listening level when the
ignition switch is turned off, when the
ignition switch is turned back on, the
volume will come back to a ªnominalº
listening level. However, if the radio
power is turned off, the volume will
remain in the position it was set at
when radio power was switched off.
*
[AS22100(MBC )10/95]
Selecting the AM or FM frequency band
*
[AS22250(MBC )02/95]
Push the ªAM/FMº button to select the desired
frequency band or to stop/store cassette tape
(when in cassette mode). Pushing the button
more than once will alternate between AM, FM1
and FM2. These functions are used with the
station memory buttons described underHow to
tune radio stations.
%*
[AS22300(MBC )10/95]
How to tune radio stations
[AS22425(MBC )06/95]
There are four ways for you to tune in to a
particular station. You can manually locate the
station by using the Automatic Music Search
(ªAMSº) button, ªSEEKº the station, ªSCANº to
the station or select the station by using the
memory buttons, which you can set to any
desired frequency.
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996

144
*
[AS23200(MBC )10/95]
q
Setting the Station Memory Preset buttons
*
[AS23300(MBC )10/95]
Your radio is equipped with 6 station
memory buttons. These buttons can be used
to select up to 6 preset AM stations and 12
FM stations (6 in FM1 and 6 in FM2).
*
[AS23400(MBC )10/95]
Follow the easy steps below to set these buttons
to the desired frequencies:
*
[AS23500(MBC )10/95]
1. Select a band, then select a frequency.
*
[AS23700(MBC )10/95]
2. Press one of the memory preset buttons and
hold the button until the sound returns. That
station is now held in memory on that
button.
*
[AS23800(MBC )10/95]
3. Follow the two steps above for each station
memory preset button you want to set.
[AS23900(MBC )09/95]
NOTE: If the vehicle's battery is disconnected,
the station memory preset buttons will
need to be reset.
*
[AS24000(MBC )10/95]
Adjusting the tone balance and speaker
output of your radio
*
[AS24100(MBC )10/95]
q
Increasing or decreasing bass response
*
[AS24250(MBC )06/95]
Push the ªAUDIOº button repeatedly until
the display reads ªBASS.º Push the right (+)
side of the ªVOLUMEº button to increase
bass (more ªlowsº), and push the left (s)
side to decrease bass (less ªlowsº).
*
[AS24300(MBC )10/95]
q
Increasing or decreasing treble response
[AS24450(MBC )06/95]
Push the ªAUDIOº button repeatedly until
the display reads ªTREB.º Push the right (+)
side of the ªVOLUMEº button to increase
treble (more ªhighsº), and push the left (S)
side to decrease treble (less ªhighsº).
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996

146
*
[AS25700(MBC )08/95]
How to locate a desired track on the tape
*
[AS25800(MBC )06/95]
NOTE: The tape track or side number
indicated in the display does not
necessarily correspond to the tape track
or side number on the cassette label. It
is used only to indicate when the tape
mechanism reverses tracks.
[AS25830(M )07/94]
q
Using the Automatic Music Search
*
[AS25850(MBC )09/95]
Press and hold the ªAMSº button (ªAMSº
will appear in the display). Then, push the
left
hbutton to rewind to the beginning
of the current selection or press the right
gbutton to fast forward to the beginning
of the next selection.
*
[AS25950(M )09/95]
q
Fast forwarding the tape
*
[AS26000(MBC )08/95]
Push the right
gbutton to fast forward
the tape.
*
[AS26150(M )08/95]
q
Rewinding the tape
*
[AS26200(MBC )08/95]
Push the left
hbutton to rewind the tape.
*
[AS26900(MBC )08/95]
q
How to change the side of the tape being
played
*
[AS27000(MBC )06/95]
The alternate track (other side) of the tape
can be selected at any time by pushing both
fast-wind buttons
hand
gat the same
time.
*
[AS27100(MBC )08/95]
How to eject the tape
*
[AS27250(MBC )08/95]
To stop the tape and eject the cassette, press the
ªEJECTº button. The radio will resume playing.
*
[AS27300(MBC )08/95]
Using the DolbyHB noise reduction feature
*
[AS27400(MBC )08/95]
NOTE: Noise reduction system manufactured
under license from Dolby Labs
Licensing Corporation. ªDolbyº and
double-D symbol are trademarks of
Dolby Laboratories Licensing
Corporation.
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996

156
*
[AS38330(M )10/95]
NOTE: Once a disc is inserted, the disc
opening is secured to prevent the
accidental insertion of a second disc.
[AS38340(M )03/95]
NOTE: The CD player has heat protection
circuitry to protect the laser diode. If
the temperature of the player reaches
167ÊF (75ÊC), theheat detection circuit
will shut off the player and ªHOTº
will appear in the display. When the
temperature is within normal operating
range, the ªHOTº indication will turn
off and the CD player will again be
operational.
*
[AS38400(M )10/95]
How to stop and restart the CD player
[AS38450(M )03/95]
When a disc is loaded, the unit automatically
enters the play mode and the play indicator (
a)
illuminates. To stop temporarily, press the
ªPLAY/STOPº button. The stop indicator (
X)in
the display illuminates and operation returns to
the radio or tape mode. To resume CD play,
press this button once again or press any other
function button (except ªEJECTº or
ªCOMPRESSº buttons).
*
[AS38475(M )10/95]
NOTE: If the ignition key is turned OFF
during play and then is set to the ON
or ACCESSORY position, the CD
player will resume playing in the mode
it was in when ignition was turned off.
*
[AS38500(M )03/95]
How to locate a selection on your CD
player using Automatic Music Search (AMS)
*
[AS38510(M )06/95]
An ªAMSº (Automatic Music Search) control on
your CD player allows you to quickly find a
particular selection on the disc. Press the left
fside of the ªAMSº control to locate a
previous selection or the right
eside of the
ªAMSº control to locate a later selection.
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996

163
[AS43459(M )03/95]
Mach 460 Sound System
*
[AS43460(MBC )08/95]
Using the Controls on Your New Radio
*
[AS43470(MBC )10/95]
How to turn the radio on and off
*
[AS43480(MBC )10/95]
Press the ªPOWERº button to turn the radio on.
Press it again to turn it off.
*
[AS43500(MBC )10/95]
How to adjust the volume
[AS43510(MBC )06/95]
Press the +/sside of the ªVOLUMEº button to
increase/decrease volume. Bars illuminate in the
display to show the relative volume level.
*
[AS43520(MBC )10/95]
NOTE: If the volume level is set above a
certain listening level when the
ignition switch is turned off, when the
ignition switch is turned back on, the
volume will come back to a ªnominalº
listening level. However, if the radio
power is turned off, the volume will
remain in the position it was set at
when radio power was switched off.
*
[AS43530(MBC )10/95]
Selecting the AM or FM frequency band
*
[AS43540(MBC )02/95]
Push the ªAM/FMº button to select the desired
frequency band or to stop/store cassette tape
(when in cassette mode). Pushing the button
more than once will alternate between AM, FM1
and FM2. These functions are used with the
station memory buttons described underHow to
tune radio stations.
%*
[AS43550(MBC )10/95]
How to tune radio stations
*
[AS43560(MBC )10/95]
There are four ways for you to tune in a
particular station. You can manually locate the
station using the ªSCAN/TUNEº button,
ªSEEKº the station, ªSCANº to the station or
select the station by using the memory buttons,
which you can set to any desired frequency.
These four methods are described below.
File:09rcasm.ex
Update:Wed Mar 27 09:33:20 1996