1996 CHEVROLET TRACKER instrument panel

Ignition Positions
4
With the key in the ignition
switch, you can
turn the
switch to four positions.,
LOCK (A): The only position in which you can remove
the key. This locks your steering wheel, ignition and
automatic transmission.
If you have an automatic transmission, the ignition
switch can’t be turned to LOCK unless the shift lever is
in the
PARK (P) position.
ACC (B): The position that you can operate your
electrical power accessories. It unlocks the steering
wheel and ignition. Use this position if your vehicle
must be pushed or towed.
ON (C): The position in which the switch returns to
after you start your engine and release the switch. The
switch stays in the
ON position when the engine is
running. But even when the engine is not running, you
can use ON to operate your electrical power accessories
and to display some instrument panel warning and
indicator lights.
START (D): The position in which the engine starts.
When the engine starts, release the key. The ignition
switch
will return to ON for normal driving.
When the engine is not running, ACC and
ON allow you
to operate your electrical accessories, such as the radio
and ventilation fan.
A warning chime will sound if you open the driver’s
door when the ignition is in ACC or LOCK and the key
is in the ignition.
2-7
ProCarManuals.com

NOTICE:
If your rear wheels can’t rotate, don’t try to
drive. This might happen if you were stuck in
very deep sand or mud or were
up against a solid
object.
You could damage your transmission.
Also, if
you stop when going uphill, don’t hold
your vehicle there with only the accelerator
pedal. This could overheat and damage the
transmission. Use your brakes to hold your
vehicle in position on
a hill.
Power Mode Selector Switch
A power mode selector
switch is included. When
you need more power for
climbing hills or quicker
acceleration, press the
P (POWER) switch. The
POWER indicator
light on the instrument panel
comes on. For normal driving, press the
N (NORMAL)
switch. The POWER indicator light goes off.
Overdrive Off Switch (Option)
The overdrive off switch is located on the left side of the
shifter. By operating the overdrive
off switch, the
four-speed automatic transmission (three-speed plus
overdrive) can be converted to a three-speed automatic
transmission. While in the three-speed mode, the
transmission will not shift into the overdrive position.
To convert the transmission to the three-speed mode,
push in the overdrive off switch and release
it. The
switch comes out and the
OD OFF indicator light on
the instrument panel comes on.
To return the transmission to the four-speed mode, push
in
the overdrive off switch again. The switch will remain
in and the
O/D OFF indicator light goes off.
Please note that if the transfer lever is in the 4L position,
the four-speed automatic transmission will remain in the
three-speed mode.
2-13
ProCarManuals.com

Horn
The lever on the left side of the steering column
includes
your:
Turn Signal and Lane Change Indicator
Headlamp High/Low Beam Changer and Passing Signal
Lighting Operation
Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal a turn
or a lane change.
To signal a tum, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
To sound the horn, press one of the horn symbols on
your steering wheel.
?ttm Signal/Multifunction Lever
An &ow on the instrument
panel will
flash in the direction
of the turn or lane change.
To signal a lane change, just
raise or lower the lever until
the arrow starts to flash.
Hold it there until you
complete your lane change.
The lever will return
by
itself when you release it.
As you signal a turn or a lane change, if the mows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses and Circuit
Breakers” in
the Index) and for burned-out bulbs.
2-28
ProCarManuals.com

Lamps Control
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.
OFF: All lamps are off.
-300: : The parking lamps, taillamps, license plate
lamp and
the instrument panel lights come on. The
headlamps are off.
-:g- : The headlamps and all other operating lamps
come on.
Lamps On Reminder
If you turn the ignition off, remove the key, open the
door and leave the lamps
on, a chime will remind you to
turn off your lamps.
Headlamp High/Low Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever away
from you.
When the high beams are
on, a light on the instrument
panel also
will be on. It will
go off when you switch to
low beam.
To switch back to low beams, pull the lever toward you.
2-29
ProCarManuals.com

Setting Cruise Control 2. Get up to the speed you want.
A CAUTION: I
If you leave your cruise control switch on when
you’re not using cruise, you might hit a button and
go into cruise when you don’t want
to. You could
be startled and even lose control. Keep the cruise
control switch
OFF until you want to use it.
1. Press the
CRUISE Cm’L
switch on the
instrument panel
to turn the system
on. The indicator
light
on the switch
will come on.
3. Once you’re going 25 mph (40 km/h) or more, turn
the lever to COAST/SET and release. Your cruise
will set.
4. Take your foot off the accelerator pedal.
2-33
ProCarManuals.com

Interior Lamps
Instrument Panel Brightness Control
This knob controls the
brightness
of your
instrument panel lights.
Turn the knob to the right to
brighten the lights
or to the
left to dim them.
Dome Lamp
The dome lamp has a
three-position switch.
1: This position is to the left when sitting in the driver’s
seat. The dome lamp
turns on and stays on whether or
not a door is open.
2: This is the center position. The lamp comes on when
a door is opened.
3: This position is to the right when sitting in the driver’s
seat. The lamp stays off even when a door is open.
2-36
ProCarManuals.com

Power Remote Control Mirrors (Option)
The switch to control the
power mirrors is located on
the instrument panel.
You
can only adjust the mirrors
when the ignition switch is
in the
ON position.
Convex Outside Mirror
To adjust the mirrors:
1.
2.
3.
Move the select,or switch to the left or right to select
the mirror you wish to adjust.
Press the outer part of the switch that matches the
direction you want to move the mirror.
Return the selector switch to the center position to
help prevent moving the mirror accidentally.
Your passenger’s side mirror is convex. A convex
mirror’s surface
is curved so you can see more from the
driver’s seat.
A CAT-TION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over
your shoulder before
changing lanes.
2-38
ProCarManuals.com

Instrument Panel -- Your Information Svstem
2-56
ProCarManuals.com