1996 AUDI S4 01E Transmission Remove And Install Workshop Manual

34-34

- On vehicle with V6 bi-turbo engine, fit
intermediate plate on dowel sleeves on engine
flange.

- Two hex socket head bolts M 10 x 60 must be replaced by new hex
bolts M 10 x 55 (Part No. N 104 684 01) so that two bolts (arrows) can
be tightened with a torque wrench after installing transmission.
- Before installing transmission, tie electrical wiring off to one side so that
it cannot be trapped between engine and transmission.

Repair Manual, 2.7 Liter V6 5V BiTurbo Engine Mechanical, Engine
Code(s): APB, Repair Group 26
- Lift transmission until clutch slave cylinder with bracket for line/hose
can be installed (arrow).
- Align exhaust system free of stress.
- Before installing, use a tap to clean threads in drive flange for
driveshaft on transmission to remove traces of locking compound.
- Replace gaskets on drive axles and on front of driveshaft Page 39
-
65
.
Pa
ge 17 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.2

34-35

- Bolt on driveshaft Page 39
-71
.

- Check adjustment of selector rod and push rod;
readjust if necessary Page 34
-12
.

- Check oil level in transmission Page 34
-39
.

- After connecting battery, enter anti-theft code for
radio

Radio operating instructions
- Close windows fully using electric window
switches.

- Operate all electric window switches again for at
least one second in "close" direction to activate
automatic one-touch function.

- Set clock to correct time.
Pa
ge 18 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.2

34-36


Vehicles with 6-cyl. bi-turbo engine
Dowel sleeves -A- for aligning. 1) The two hex socket head bolts M 10 x 60 must be replaced by new hex
bolts M 10 x 55 (Part No. N 104 684 01) so that the two bolts -4- can be
tightened with a torque wrench after installing the transmission. No.
Bolt
Qty.
Nm
1 M 12 x 90 2 65
2 M 12 x 100 1 65
3 M 10 x 60 1 45
4
M 10 x 60
1)
2 45
5 M 10 x 150 1 65
6 M 12 x 130 1 65
7 M 12 x 80 2 65
Pa
ge 19 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.2

34-37

Component

Nm
Clutch slave cylinder to transmission
1)
20
Transmission support to transmission 40
Engine speed sender -G28- 10
Drive axle to drive flange M8
M10 40
80
Heat shields above drive axles to
transmission 25
Push rod to transmission 40
Selector rod to transmission 23
Connecting rod for selector rod to
transmission 23
Catalytic converter to mounting lugs 25
Front exhaust pipe to turbocharger 30
Heat shield to turbocharger/exhaust pipe 10
Clamp for exhaust pipe 40
Bracket for noise insulation to subframe 10
Driveshaft to transmission
1)
55
Heat shield for driveshaft to Torsen
differential cover 25

1) Always replace bolts
Pa
ge 20 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.2

34-38


Subframe to body 1) Always replace bolts washers Support -A- to body -arrow 1- 75
Subframe to body
1) (arrow -2-)
115 + 90
Transmission mounting to subframe (arrow -3-) 25

For 6-cylinder bi-turbo engine only 1) Install bolts -1- from the bottom. Always replace nuts and bolts. Cross-piece -A- to subframe
1)
40 + 90
Pa
ge 21 of 21 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM03.34.2