1996 AUDI A4 ECU

13-4


- Remove bolt -2- and screw in special tool 3369.
- Screw in special tool 3369 into bore -5-.
- Remove bolts -1- and -3-.
- Remove bolts -4- and pull lock carrier out as far
as it will go.
- Secure lock carrier with suitable M6 bolts in hole
-6- (lock carrier) and hole -7- (fender panel).
Pa
ge 4 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-11


14 -
Generator
Removing:
- Disconnect battery Ground strap
- Remove air duct hose to charge air
cooler.
- Loosen ribbed belt and take belt off
Generator Page 13
-18
.
- Remove viscous fan and put into radiator
cowl.
- Remove electrical wiring from Generator.
- Loosen connections for Generator from
top and bottom and remove Generator.
Installing:
- To facilitate attachment of Generator
slightly drive back thread bushing for
securing bolt at bracket.
Pa
ge 11 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-15


2 -
Air conditioner compressor
Do not loosen or disconnect refrigerant
hoses or lines. After removing compressor from
mountings, secure to chassis side member
with wire or similar. Do not leave
compressor suspended on refrigerant
hoses.
3 -
Dowel sleeve Check sleeve is correctly seated in bracket
4 -
33 Nm
5 -
Bracket For A/C compressor
6 -
Tensioner For ribbed beltRemoving and installing ribbed belt
Page 13
-18

Pa
ge 15 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-18

Ribbed belt, removing and installing


Note:
Mark the direction of rotation with chalk or felt
pen before removing the ribbed belt. If the belt
rotates in the wrong direction when it is refitted,
belt breakage may result. Ensure that the belt is
properly seated on the pulleys when installing.

Removing

- Remove sound insulation -arrows-.

- Loosen bolts securing ribbed belt tensioning roller for A/C compressor -
arrows-.
Pa
ge 18 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-19


Note: - Turn tensioner in direction of arrow to loosen ribbed belt.
- Remove ribbed belt from Generator and release tensioner.

When the lock carrier is in the service position, the ribbed belt tensioner
can be secured to prevent it from turning by inserting a suitable pin or
Allen key -arrow- into the holes.
Pa
ge 19 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-21

Viscous fan, removing and installing


Removing

Lock carrier must be in service position
Page 13
-1 .

- To loosen ribbed belt, turn tensioner in direction of arrow.
- Remove ribbed belt from Generator pulley.

- Secure pulley for viscous fan with pin punch -1- and remove using
Allen key -2-.
- Remove viscous fan.
Pa
ge 21 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-25


- Secure pulley for viscous fan with pin punch -1- and remove using
Allen key -2-.
- Remove viscous fan from mounting.

- Remove intake pipe support -arrows-.
Pa
ge 25 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1

13-30


- To loosen ribbed belt, turn tensioner in direction of arrow.
- Remove ribbed belt from Generator pulley.

- Secure pulley for viscous fan with pin punch -1- and remove using
Allen key -2-.
- Remove viscous fan from mounting and put in front of radiator cowl.
- Remove wiring from rear of Generator.
- Loosen connections for Generator from top and bottom and remove
Generator.
Pa
ge 30 of 47 En
gine, disassemblin
g and assemblin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.1