1996 AUDI A4 diagram

24-90

Voltage supply to Engine Control
Module (ECM), checking


Required special tools and test equipment

VAG1551 or VAG1552 Scan Tool (ST) with
VAG1551/3 adapter cable
VAG1598/22 test box
Multimeter US1119 (Fluke 83 or equivalent)
VW1594 connector test kit
Wiring diagram

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with ignition
switched on) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Pa
ge 115 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-93

Checking voltage supply at terminal 30

- Switch ignition off.

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Connect multimeter US1119 (Fluke 83 or
equivalent) between ECM/test box sockets 2
(Ground) and 3 (B+), using adapter cables from
VW1594 connector test kit.

Specified value: 10-14.5 volts
If voltage is NOT OK:

- Check wiring according to applicable wiring
diagram.
Pa
ge 119 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-94

Checking voltage supply at terminal 15

- Switch ignition off.

- Connect VAG1598/22 test box to ECM harness
connector page 01
-67
.

- Connect multimeter between ECM/test box
sockets 1 (B+) and 2 (Ground), using adapter
cables from VW1594 connector test kit.

- Switch ignition on, and check voltage.

Specified value: 10-14.5 volts
If voltage is NOT OK:

- Check wiring according to applicable wiring
diagram.

- Check readiness code page 01
-70
. If
Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code page 01
-73
.
Pa
ge 120 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-96
If the fuel pump does not respond:

- Check fuel pump relay actuation page 24
-
99
.
If the LED test light does not light up:

- Repeat test at other terminal of fuse 28.

If the LED light still does not light up:
- Check wiring for open or short circuits between fuse 28 and terminal 30
at relay position 6, using the applicable wiring diagram. Repair wiring
as necessary.

Specified value: max. 1.5

Note:
This step lets the fuel pump run without the engine running. The closed
throttle position switch must be closed during the test, or the selected fuel
injector will discharge fuel when it is actuated 5 times. - Connect VAG1527B LED voltage tester between Ground and one of
the two terminals for fuse 29.
Pa
ge 122 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-97
If the LED test light does not light up:

- Repeat test at other terminal of fuse 29.

If the LED test light still does not light up:
- Check wiring for open circuit between fuse 29 and terminal 30 at relay
position 6, using the applicable wiring diagram. Repair wiring as
necessary.

Specified value: max. 1.5

Note:
This step lets the fuel pump run without the engine running. The closed
throttle position switch must be closed during the test, or the selected fuel
injector will discharge fuel when it is actuated 5 times. - Connect VAG1527 LED voltage tester between Ground and one of the
two terminals of fuse 34.
- Initiate output Diagnostic Test Mode (DTM) and advance to test of
cylinder 1 fuel injector -N30- page 01
-51
.

LED test light must light up
Fuel pump relay must be activated
Pa
ge 124 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-98
If the LED test light does not light up:

- Repeat test at other terminal of fuse 34.

If the LED test light still does not light up:
- Check wiring for open circuit between fuse 34 and terminal 31 at relay
position 6, using the applicable wiring diagram. Repair wiring as
necessary.

Specified value: max. 1.5
Pa
ge 126 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-99

Checking fuel pump relay voltage supply and
actuation

- Remove fuel pump relay -J17- from relay panel
position 6.

Checking fuel pump relay voltage supply

- Switch ignition on.

If voltage is NOT OK: - Connect multimeter US1119 (Fluke 83 or similar) and check for voltage
at relay socket:

Terminals 28 (B+) and 34
Terminals 32 (B+) and 34
Specified values: approx. Battery Positive Voltage (B+)
- Repair wiring according to applicable wiring diagram.
Pa
ge 127 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-100

Checking fuel pump relay actuation

Note:
The LED light will light dimly before and after cranking the starter.
If the LED test light does not light up while cranking the starter, check
wiring as follows. - Connect VAG1527B LED voltage tester between relay socket terminals
28 (B+) and 29.
- Briefly crank starter.
LED test light must light up.

If resistance is NOT OK:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder. - Connect VAG1598/22 test box to ECM harness connector page 01
-
67
. (Numbers marked on ECM connector match those on test box).
- Connect multimeter US1119 (Fluke 83 or equivalent) to check for open
circuit between relay socket terminal 29 and test box socket 4.

Specified value: max. 1 - Repair wiring using applicable wiring diagram.
Pa
ge 128 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1