1996 AUDI A4 01W Transmission Disassemble And Assemble Workshop Manual

34-52


- Remove transmission cover -A- from transmission housing -B-.

- Remove bolts (arrows) and pull out multi-function switch.
Pa
ge 17 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-53


- Remove relay shaft bolts (arrows).

- Unbolt shift detent (arrow) and swing out.
Pa
ge 18 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-54


- Input shaft -A-, pinion shaft -B-, relay shaft -C-, selector rods -D- with
shift rod and shift forks -E- must all be carefully pulled out together.
Pa
ge 19 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-55

Installing

Note:
If the input shaft ball bearing, the input shaft or
the transmission housing is replaced, it is
necessary to re-determine the thickness of the
circlips for the input shaft first Page 35
-17
,
input shaft adjusting.

- For easier installation of following components, swing transmission
housing into position shown.

Note:
The relay shaft -C- and the shift rod can also be installed later if
necessary Page 34
-56
, Illustration V34-1816 and Page 34
-57
,
illustration V34-2120 - Assemble input shaft -A-, pinion shaft -B-, relay shaft -C-, selector rods
-D- with shift rod and selector forks -E-.
- Install these components into transmission housing as a set.
Pa
ge 20 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-56


Position of shift mechanism in transmission
Note:
Illustration is shown without the drive axle and pinion. 1 - Shift fork 5th and reverse gears
2 - Shift fork 3rd and 4th gears
3 - Shift fork 1st and 2nd gears
4 - Relay shaft
5 - Shift detent
6 - Shift rod

- Move transmission housing and engage 3rd gear (direction of arrow).
Pa
ge 21 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-57


- Install relay shaft -A-.
- Place inner shift rod -B- sideways into mounting hole in transmission
housing and assemble into mounting eye.
- Carefully turn shift rod in direction shown (arrow).

- Insert shift detent and tighten bolt (arrow) securely.
Pa
ge 22 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-58


- Install relay shaft stop bolts (arrows).
- Replace O-ring for multi-function switch.

- Carefully insert multi-function switch and tighten (arrows).
Pa
ge 23 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4

34-59


Make sure dowel sleeves for transmission cover -A- are installed in
transmission housing -B-.
- Coat sealing surfaces with a thin layer of sealant AMV 188 001 02.
- Install transmission cover onto transmission housing.

- Install rear circlip (arrow) for input shaft ball bearing.
- Slide ball bearing onto input shaft.
Installation position: closed side of ball cage faces toward transmission
housing.
Pa
ge 24 of 26 Transmission, disassemblin
g and assemblin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.4