1995 RENAULT MEGANE SCENIC warning

VEHICLES
AUTOMATIC TRANSMISSION
Gear change thresholds
23
The figures given in the table represent the average theoretical speed values for changing gear in km/h
tolerances = ± 10 %.
PL: No load.
PF: Full load.
RC: Kickdown (changing to a lower gear).
A: Gear change thresholds are set lower down. Gears change at a lower speed. Switch (1) is not activated
and the warning light EXC is extinguished.
B: Gear change thresholds are set higher up. Gears change at a higher speed. Switch (1) is activated and the
warning light
EXC is illuminated.
1 22 33 44 33 22 1
ABABABABABAB
5059PL
ACCELER-
ATOR
POSITION
TRANS-
MISSION TYPE
BA0AD4PF
RC
4149
52
7695
96
126149
158
10712765812832
162040466473
14690
7153234
48
98597R
23-4

AUTOMATIC TRANSMISSION
Oil change frequencies
23
The mechanism is drained during the major service.
The oil level must be checked every 10000 miles (15 000 km) in case there is a slight oil leak.
The final drive is never drained ; it is filled for life.
The strainer is no longer replaced (NT 2261A).
Only the level may change due to a slight leak.
Oil capacity
NOTE :if the automatic transmission is replaced, only check the oil level since the transmission is supplied by
the Parts Department full of oil.
TOTAL volume
MECHANISM
5.7 l
FINAL DRIVE1 l
Fault warning light
MESSAGE FROM THE ELECTRONIC FAULT
WARNING LIGHT
Normal operation :
• The warning light is not illuminated during
normal operation whether the vehicle is being
started, engine running or when the vehicle is
stationary.
Presence of a fault :
• Vehicle stopped, engine running, or when
driving, warning light permanently illuminated
• Vehicle moving, warning light illuminates and
extinguishes without action at the ignition key.
• Vehicle moving, warning light illuminates
briefly.Oil temperature < - 20 °C or > + 140 °C
• Vehicle moving or stationary, warning light
flashes at a rate of approximately 1 flash per
second, in this case, reduce the performance
requirement by moderating acceleration.
23-6

AUTOMATIC TRANSMISSION
Wiring diagram
23
104 - Ignition switch
119 - Automatic transmission computer
120 - Injection computer
129 - ECO/PERF selector switch
160 - Stop switch
163 - Starter motor
225 - Diagnostic socket
247 - Double headlight relay
250 - Speed sensor
303 - Automatic transmission selector lighting
319 - Air conditioning control panel
535 - ECO/PERF selector switch warning light
569 - 4 speed automatic transmission kickdown
597 - Engine fuse box
645 - Passenger compartment connection unit
754 - Electrical/hydraulic interface
779 - Automatic transmission multifunction switch
780 - Automatic transmission turbine or vehicle speed sensor
781 - Line pressure sensor
R22 - Engine/automatic transmission
R34 - Engine/dashboard
MH - Engine electric earth
MJ - Front right pillar electric earth
23-27

NON-SIDE OPENING ELEMENTS
Luggage compartment lid
48P
48-4
Remove the four mounting bolts (B) from the upper
hinge.
WARNING: at this moment, a second person is
needed.
Remove:
– the three mounting bolts (C) from the upper hinge,– the two mounting bolts (D) on the lower hinge body,
if necessary.
REFITTING
Refit in reverse order to removal.
REMINDER: when refitting the hinges, ensure that the
mating surfaces are sealed with beading mastic (see
Technical Note n˚ 396A).
17515R
17517R17628R
D

NON-SIDE OPENING ELEMENT MECHANISMS
Rear screen and luggage compartment lid locks
52
52-4
REMOVING THE STRIKER PLATE AND THE PAD
ON THE BODY
Remove:
– the two striker plate bolts,
– the two pad bolts.
NOTE: the movement arrows indicate the adjustment
options.REFITTING
To refit, proceed in the reverse order to removal.
WARNING: If removing the striker plate and the pad
at the same time, the striker plate is no longer
supported.
16878S
A

EXTERIOR PROTECTION
Rear bumper
55PRear bumper
REMOVAL
After removing the rear wing extenders
(section 55-D),
Remove:
– the three lower mounting bolts (A),– the four upper mounting bolts (B),
– the luggage compartment lid balancers and its
mounting ball joint (C).
WARNING: the balancer acts as a door check strap. It
is necessary hold the cover using string.
Release the bumper.
REFITTING
To refit, proceed in the reverse order to removal.
18062R
17897R
55-13
F

EXTERIOR ACCESSORIES
Rear windscreen wiper arm
56SRear windscreen wiper arm
PRF5606
WARNING: Use the special tool Elé. 1552 to remove the rear screen wiper arm.
56-2
B