1995 OLDSMOBILE AURORA tow

Remote Fuel Door Manual Release
The fuel door can be
opened lnanually
in
case of an electrical
power failure.
To do
so, first open the trunk.
The release nlechanisln
is on the driver’s side
of the vehicle, at the
top of the
trunk
compartment. Pull the
tab toward you to
release the
fuel door.
NOTICE:
Prying on a locked fuel filler door could damage
it. Use the remote fuel door manual release
located in the trunk.
Filling Your Tank
The cap is behind a hinged door on the left side of your
vehicle.
6-5
ProCarManuals.com

To Check Engine Oil
Pull out the dipstick and clean it with a paper towel or
cloth, then push it back
in all the way. Remove it again,
keeping the tip down, and check the level.
When to Add Oil
If the oil is at or below the ADD line. then you’ll need
to add some oil.
But you must use the right kind. This
part explains what kind
of oil to use. For crankcase
capacity. see ”Capacities and Specifications”
in the
Index.
NOTICE:
Don’t add too much oil. If your engine has so
much oil that the oil level gets above the upper
mark that shows the proper operating range,
your engine could be damaged.
Just fill it enough to put the level somewhere in the
proper operating range. Push the dipstick all the way
back
in when you‘re through.
6-11
ProCarManuals.com

As shown in the chart, SAE 10W-30 is best for your
vehicle. However,
you can use SAE SW-30 if it’s going
to be colder than
60°F (16°C) before your next oil
change. When it‘s very cold. you should use
SAE
SW-30. These numbers on an oil container show its
viscosity,
or thickness. Do not use other viscosity oils,
such
X SAE 2OW-SO.
NOTICE:
Use only engine oil with the American Petroleum
Institute Certified For Gasoline Engines
“Starburst” symbol. Failure to use the proper oil
can result in engine damage not covered by your
warranty.
GM Goodwrench@ oil (in Canada, GM Engine Oil)
meets all the requirements for your vehicle.
Engine Oil Additives
Don’t add anything to your oil. Your Aurora retailer is
ready
to advise if you think something should be added.
When to Change Engine Oil
See if any one of these is true for you:
0 Most trips are less than 5 to I0 miles (8 to 16 km).
This is particularly important when outside
temperatures are below freezing.
Most trips include extensive idling (such as frequent
driving
in stop and go traffic).
Most trips are through dusty areas.
0 You frequently tow a trailer or use a carrier on top of
your vehicle.
If any one of-. these is true for your vehicle, then you
need to change your oil and filter every 3,000 miles
(5 000 km) or 3 months -- whichever comes first. (See
“Change Oil Message”
in the Index.) If the CHANGE
OIL NOW message appears in the Driver Information
Center,
you should change your oil.
If none of them is true, change the oil and filter every
7,500 miles
( 12 SO0 km) or 12 months -- whichever
colnes first. (See “Change Oil Message’‘
in the Index.)
Always reset the engine oil life to 100% after every oil
change.
6-13
ProCarManuals.com

4. There's a temperature sensor on the corner of the air
cleaner cover. Use
a screwdriver to release the
sensor's electrical connector retainer, and
pull up.
5. Unsnap the two clamps by pushing down on the top
of the air cleaner cover and pushing in on the clamps
toward the center
of the cover. Then remove the
cover.
A. Remove the air filter.
7. Install the new air filter and reverse all steps to
reinstall the cover. electrical wires, duct and clamp.
Be sure the
tabs of the air cleaner cover fit into the
slots
of the air cleaner housing. Then make sure both
clamps are
f~~lly engaged.
6- 15
ProCarManuals.com

Wait at least 30 minutes before checking the transaxle
fluid level
if you have been driving:
0 When outside temperatures are above 90°F (32°C).
0 At high speed for quite a while.
0 In heavy traffic -- especially in hot weather.
0 While pulling a trailer.
To get the right reading, the fluid should be at normal
operating temperature, which
is 180°F to 200°F (82°C
to 93
"C).
Get the vehicle warmed up by driving about 15 miles
(24 km) when outside temperatures are above 50°F
(10°C). If it's colder than 50°F (lO"C), you may have
to drive longer.
To check the fluid level
Park your vehicle on a level place. Keep the engine
running.
With the parking brake applied, place the shift lever
in PARK (P).
0 With your foot on the brake pedal, move the shift
lever through each gear range, pausing for about
three seconds
in each range. Then, position the shift
lever
in PARK (P).
0 Let the engine run at idle for three to five minutes.
Then, without shutting off the engine, follow these
steps:
1. Pull out the dipstick and wipe it with a clean rag or
paper towel.
2. Push
it back in all the way, wait three seconds and
then pull
it back out again.
6-17
ProCarManuals.com

0 If a ring forms after spot cleaning, clean the entire
area immediately or
it will set.
Using Foarn-']lSrpe Cleaner on Fabric
0
0
0
0
0
0
Vxuum and brush the area to remove any loose dirt.
Always clean a whole trim panel or section. Mask
surrounding trim along stitch or welt lines.
Mix Multi-Purpose Powdered Cleaner following the
directions
011 the container label.
Use suds only and apply with a clean sponge.
Don't saturate the material.
Don't rub
it roughly.
As soon as you've cleaned the section, use a sponge
to remove the suds.
Rinse the section with
a clean, wet sponge.
Wipe off what's left
with a slightly damp paper towel
or cloth.
Then dry
it immediately with a blow dryer or a heat
lamp.
NOTICE:
I Be careful. A blow dryer may scorch the fabric. I
0 Wipe with a clean cloth.
Using Solvent-Type Cleaner on Fabric
First, see if you have to use solvent-type cleaner at all.
Some spots and stains
will clean off better with just
water and mild soap.
If you need to use a solvent:
0 Gently scrape excess soil from the trim material with
a clean, dl111 knife or scraper. Use very little cleaner,
light pressure and clean cloths (preferably
cheesecloth), Cleaning should start at the outside
of
the stain, "feathering" toward the center. Keep
changing to
a clean section of the cloth.
0 When you clean a stain from fabric, immediately dry
the area
with a blow dryer to help prevent a cleaning
ring. (See the previous NOTICE.)
6-44
ProCarManuals.com

Cleaning the Outside of the
Windshield and Wiper Blades
If the windshield is not clear after using the windshield
washer,
or if the wiper blade chatters when running, wax
or other material may be
on the blade or windshield.
Clean the outside
of the windshield with GM
Windshield Cleaner, Bon-Ami Powder@ (GM Part
No. 10500 I 1). The windshield is clean if beads do not
form when you rinse
it with water.
Clean the blade by wiping vigorously with a cloth
soaked
in full strength windshield washer solvent. Then
rinse the blade with water.
Wiper blades should be checked
on a regular basis and
replaced
when worn.
Weatherstrips
Silicone grease on weatherstrips will make them last
longer, seal better, and not stick or squeak. Apply
silicone grease with
a clean cloth at least every six
months. During very cold, damp weather more frequent
application may be required. (See "Recommended
Fluids and Lubricants"
in the Index.)
Cleaning the Outside of Your Aurora
The paint finish on your vehicle provides beauty, depth
of color, gloss retention and durability.
Washing Your Vehicle
The best way to preserve your vehicle's finish is to keep
it clean by washing it often with lukewarm or cold
water.
Don't wash your vehicle
in the direct rays of the sun.
Don't use strong soaps or chemical detergents. Use
liq~~id hand, dish or car washing (mild detergent) soaps.
Don't use cleaning agents that are petroleum based, or
that contain acid or abrasives.
All cleaning agents
should be flushed promptly and not allowed to dry on
the surface, or they could stain. Dry the finish
with a
soft, clean chamois or a
100% cotton towel to avoid
surface scratches and water spotting.
High pressure vehicle washes may cause water to enter
your vehicle.
ProCarManuals.com

Add-on Electrical Equipment
NOTICE:
Don’t add anything electrical to your Aurora
unless you check with your retailer first. Some
electrical equipment can damage your vehicle
and the damage wouldn’t be covered by your
warranty. Some add-on electrical equipment can
keep other components from working as they
should.
Your vehicle
has an air bag system. Before attempting to
add anything electrical to your AL~I-o~~, see “Servicing
Your Air Bag-Equipped Aurora”
in the Index.
Removing the Rear Seat Cushion
To access the battery and main fuse boxes, the rear seat
cushion must be removed. You may wish to have your
retailer do this for you.
NOTICE:
The battery and main fuse boxes are located
under the rear seat cushion. The battery’s ground
terminal and some relay wires are exposed. To
help avoid damage to the battery and wires, be
careful when removing or reinstalling the seat
cushion.
Do not remove covers from covered
parts.
Do not store anything under the seat, as
objects could touch exposed wires and cause
a
short.
To Remove the Rear Seat Cushion
1. Pull up on the front of the cushion to release the
front
hooks.
2. Pull the cushion up and out toward the front of the
vehicle.
ProCarManuals.com