1995 OLDSMOBILE AURORA tow

Parking Brake
To set the parking brake,
hold the regular brake pedal
down with your right foot.
Push down the parking
brake pedal with your
left
foot. If the ignition is on,
the parking brake indicator
light will come on.
If
you try to drive off with the parking brake on, the
parking brake indicator light stays on. The PARK
BRAKE SET message will appear in the Driver
Information Center, and a chime will sound until you
release the parking brake
or recycle the ignition. This
vehicle has
a PUSH TO RELEASE parking brake
pedal. To release
the parking brake, hold the regular
brake down and push
the parking brake pedal with your
left foot. This will unlock the pedal. When you lift your
left foot, the parking brake pedal will follow it
to the
released position.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have
to
replace them, and you could also damage other
parts
of your vehicle.
If you are towing a trailer and are parking on any hill,
see “Towing a Trailer” in the Index. That part shows
what
to do first to keep the trailer from moving.
2-24
ProCarManuals.com

Shifting Into PARK (P)
1. Hold the brake pedal down with your right foot and
set the parking brake.
2. Move the shift lever into the PARK (P) positions as
follows:
0 Hold in the button on the lever.
Push the lever all the way toward the front of
your vehicle.
3. Move the ignition key to LOCK.
4. Remove the key and take it with you. If you can
walk away from your vehicle with the ignition key in
your hand, your vehicle is in PARK (P).
2-25
ProCarManuals.com

Power Windows
Follow the proper steps to be sure your vehicle won’t
move. See “Shifting Into PARK (P)” in the Index.
If you are parking on a hill and if you’re pulling a
trailer, also see “Towing a Trailer” in the Index. Switches
on the driver’s armrest control each
of the
windows when the ignition is on. In addition, each
passenger door
has a switch for its own window.
The driver’s window switch has an express down
feature.
When it is held rearward for more than half a
second, the window will lower completely. The window
can be opened
in smaller amounts by pressing the switch
rearward and releasing
it immediately.
To stop the window while it is lowering, press the
switch again, then release. To raise the window, hold the
switch forward.
ProCarManuals.com

Windshield Wipers
The lever on the right side of your steering column
controls your windshield wipers.
For a single wiping cycle, move the lever up to MIST.
Hold
it there until the wipers start, then let go. The
wipers
will stop after one cycle. If you want more
cycles, hold the lever to
MIST longer.
For steady wiping at low speed, push the lever down to
the
LO position. For high speed wiping, push the lever
down further, to
HI. To stop the wipers, move the lever
to
OFF.
YOLI can set the wiper speed for a long or short delay
between wiper cycles. This can be very useful
in light
rain or snow. Push the lever down to the first detent,
DELAY. Turn the band closer to the short lines for fewer
wiper passes per minute.
As you turn the band toward
the long lines, the wiper cycles per minute will increase.
Remember that damaged wiper blades may prevent you
from seeing well enough
to drive safely. To avoid damage,
be sure to clear ice and snow from the wiper blades before
using them.
If they're frozen to the windshield, carefully
loosen or thaw them.
If your blades do become damaged,
get new blades
or blade inserts.
Heavy snow or ice can overload your wipers.
A circuit
breaker will stop them
until the motor cools. Clear away
snow or ice to prevent
an overload.
2-31
ProCarManuals.com

Windshield Washer
The lever on the right side of your steering column also
controls your windshield washer.
To spray washer fluid
on the windshield, pull the lever toward you. The wipers
will clear the window and then either stop or return to
your preset speed. For more washer cycles, pull and
hold the lever.
If the fluid level in the windshield washer bottle is low,
the message LOW WASHER FLUID will appear in the
information center. See “Windshield Washer Fluid” in
the Index.
Driving without washer fluid can be dangerous.
A bad
mud splash can block your vision.
You could hit another
vehicle or go off the road. Check your washer fluid level
often.
NOTICE:
When using concentrated washer fluid,
follow the manufacturer’s instructions for
adding water.
Don’t mix water with ready-to-use washer
fluid. Water can cause the solution to freeze
and damage your washer fluid tank and
other parts of the washer system. Also,
water doesn’t clean
as well as washer fluid.
Fill your washer fluid tank only
3/4 full
when it’s very cold. This allows for
expansion, which could damage the tank if
it
is completely full.
Don’t use radiator antifreeze in your
windshield washer. It can damage your
washer system and paint.
2-32
ProCarManuals.com

Headlamps
300: Turn the band to this symbol to turn on:
Parking Lamps
%
0 Side Marker Lamps
0 Taillamps
Instrument Panel Lights
License Plate Lamps
/, Turn the band to this symbol to turn on:
Headlamps
-'Q-
Parking Lamps
Side Marker Lamps
0 Taillamps
Instrument Panel Lights
License Plate Lamps
Turn the band to
OFF to turn off the lamps/lights.
Headlamp High-Low Beam
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you. Then release
it.
When the high beams are on, a blue light on the
instrument panel also will be on.
2-39
ProCarManuals.com

Flash-To-Pass Feature
This feature lets you use your high beam headlamps to
signal a driver in front of you that you want to pass. It
works even
if your headlamps are off.
To use it, pull the turn signal lever toward you.
If your headlamps are off, your high beam headlamps
will turn on. They’ll stay on as long as you hold the
lever there. Release the lever to turn them off.
If your headlamps are on, but on low beam, the system
works normally. Just pull the lever until it clicks. Your
headlamps will shift to high beam and stay there. To
return to low beam, just pull the lever toward you.
If your headlamps are on, and on high beam, your
headlamps will switch to low beam.
To get back to high
beam, pull the lever toward you.
Cornering Lamps
I
The cornering lamps are designed to come on when you
signal a turn. This will provide more light for cornering
at night.
2-40
ProCarManuals.com

To operate the Twilight Sentinel, rotate the Twilight
Sentinel control to
MAX for a three-minute delay.
Rotate it toward
MIN to reduce the delay. Rotate the
control all the way to
MIN to turn off the Twilight
Sentinel. These
lamps work even
when the ignition is off. To
avoid draining your vehicle’s battery, be sure to turn off
all front and rear reading lamps when leaving your
vehicle.
Front Reading Lamps Rear Reading Lamps
These lamps and
the interior courtesy lamps will come
on when you open a door. They will turn off when
you
turn on the ignition. If the door is left open, they will
turn off after about
10 minutes.
To turn on the reading lamps when the doors are closed,
press the button behind the lamp you want
on. Press it
again
to turn the lamp off.
These lamps go on when you open the doors. You can
also turn them on by pressing the button to the side of
the lamp. Press it again to turn them off.
These lamps work even when the ignition
is off. To avoid
draining
your vehicle’s battery, be sure to turn off all front
and rear reading lamps when leaving your vehicle.
2-43
ProCarManuals.com