1995 OLDSMOBILE AURORA reset

Shoulder Belt Tightness Adjustment 4.
Your car has a shoulder belt tightness adjustment
feature.
If the shoulder belt seems too tight, adjust it
before you begin to drive.
1. Sit well back in the seat.
2. Start pulling the shoulder belt out.
l 3. Just before it reaches the end, give it a quick pull.
I
Let the belt go back all the way. You should hear a
slight clicking sound.
If you don’t, the adjustment
feature won’t set, and you’ll have
to start again.
5. Now you can add a small amount of slack. Lean
forward slightly, then sit back. If you’ve added more
than
1 inch (25 mm) of slack, pull the shoulder belt
out as
you did before and start again.
If you move around in the vehicle enough, or if you pull
out the shoulder belt, the belt will become tight again.
If
this happens, you can reset it.
1-12
ProCarManuals.com

Windshield Washer
The lever on the right side of your steering column also
controls your windshield washer.
To spray washer fluid
on the windshield, pull the lever toward you. The wipers
will clear the window and then either stop or return to
your preset speed. For more washer cycles, pull and
hold the lever.
If the fluid level in the windshield washer bottle is low,
the message LOW WASHER FLUID will appear in the
information center. See “Windshield Washer Fluid” in
the Index.
Driving without washer fluid can be dangerous.
A bad
mud splash can block your vision.
You could hit another
vehicle or go off the road. Check your washer fluid level
often.
NOTICE:
When using concentrated washer fluid,
follow the manufacturer’s instructions for
adding water.
Don’t mix water with ready-to-use washer
fluid. Water can cause the solution to freeze
and damage your washer fluid tank and
other parts of the washer system. Also,
water doesn’t clean
as well as washer fluid.
Fill your washer fluid tank only
3/4 full
when it’s very cold. This allows for
expansion, which could damage the tank if
it
is completely full.
Don’t use radiator antifreeze in your
windshield washer. It can damage your
washer system and paint.
2-32
ProCarManuals.com

2. Get up to the speed you want. To Resume a Set Speed
3. Push in the SET button at the end of the lever and
release
it. The CRUISE light on your instrument
panel will come on.
4. Take your foot off the accelerator pedal. Suppose
you set your cruise control at
a desired speed
and then you apply the brake. This,
of course, shuts off
the cruise control. But you don’t need to reset it. Once
you’re going about
25 mph (40 km/h) or more, you can
move the cruise control switch from
ON to RES/ACC
(Resume/Accelerate) for about half a second.
You’ll
go right back up to your chosen speed and stay
there.
If you hold the switch at RES/ACC longer than half a
second, the vehicle will keep going faster until you
release the switch or apply
the brake. You could be
startled and even lose control.
So unless you want to go
faster, don’t hold the switch at REWACC.
2-36
ProCarManuals.com

To Increase Speed While Using Cruise
Control
There are two ways to go to a higher speed. Here’s the
first:
1. Use the accelerator pedal to get to the higher speed.
2. Push the button at the end of the lever, then release
the button and the accelerator pedal. You’ll now
cruise at the higher speed.
Here’s the second way to
go to a higher speed:
I. Move the cruise switch from ON to RES/ACC. Hold
it there until you get up to the speed you want, and
then release the switch.
2. To increase your speed in very small amounts, move
the switch to REWACC for less than half a second
and then release
it. Each time you do this, your
vehicle
will go about 1 mph (I .6 km/h) faster.
The accelerate feature will only work after you turn on
the cruise control by pushing the
SET button.
To Reduce Speed While Using Cruise
Control
There are two ways to reduce your speed while using
cruise control:
0 Push in the button at the end of the lever until you
reach the lower speed you want, then release
it.
0 To slow down in very small amounts, push the
button for less than half a second. Each time
you do
this, you’ll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down
to the cruise control speed you set earlier.
If you increase your speed over 20 mph (32 km/h),
cruise control will be disabled. You will then have
to
reset your cruise control.
ProCarManuals.com

@
EMiUM UNLEAOED FUEL ON C
Your trip odometer tells you how far you have driven
since
you last reset it. Press the trip button located next
to the trip odometer, below the fuel gage.
Your Aurora has a tamper resistant odometer.
If you see
silver lines between the numbers, you’ll know someone
has probably tampered with it and the numbers may not
be true.
You
may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to the
mileage total
of the old odometer, then it must be. But if
it can’t, then it’s set at zero and a label must be put on
the driver’s door to show the old mileage reading when
the new odometer was installed.
Tachometer
2
The tachometer displays the engine speed in revolutions
per minute
(RPM).
If your engine speed equals or exceeds the safe limit for
operation, the message HOT
... REDUCE ENGINE RPM
is displayed on the information center.
2-62
ProCarManuals.com

Anti-Lock Brake System Warning Light
ANT’- (@)
LOCK
With the anti-lock
brake system, this light
will come
on when
you start your engine
and may stay
on for
several seconds. That’s
normal. If the light
doesn’t come on, have
it fixed so it will be
ready to warn you if
there is a problem.
If the light stays on, turn the ignition off. Or, if the light
comes on when you’re driving, stop as soon as possible
and turn the ignition
off. Then start the engine again to
reset the system.
If the light still stays on, or comes on
again while you’re driving, your Aurora needs service.
If
the regular brake system warning light isn’t on, you
still have brakes, but you don’t have anti-lock brakes. If
the regular brake system warning light is also on, you
don’t have anti-lock brakes and there’s a problem with
your regular brakes. See “Brake System Warning Light’’
earlier in this part.
Traction Control System Warning Light
TRACTION
OFF
This warning light should come on briefly as you start
the engine.
If the warning light doesn’t come on then,
have it fixed
so it will be ready to warn you if there’s a
problem. If it stays
on, or comes on when you’re
driving, there may be a problem with your traction
control system and your vehicle may need service.
When this warning light
is on, the system will not limit
wheel spin. Adjust your driving accordingly.
ProCarManuals.com

Turn on the system by pressing any button except
RESET, ENTER or
OFF. When you turn on the ignition,
the Driver Information Center will be
in the mode last
displayed when
the engine was turned off. Keep in mind
that this also applies to the
OFF mode.
To turn off messages
on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET and the hot engine warnings), press any button on
the
DIC.
I \ 1, I
You will need to open the cover to access the control
buttons.
To open the cover, push the button located to
the right of the cover.
To close the cover, push it down to its closed position.
Fuel Economy
The ECON button displays average fuel economy and
instantaneous fuel economy calculated for
your specific
driving conditions. Press
ECON to display average fuel
economy, such as:
25.2 AVG MUGAL or
9.3 AVG L/ 100 KM
Press
ECON again to display instantaneous fuel
economy, such as:
28 TNST MUGAL or
8.4 INST L/ 100 KM
Press again to return to average fuel economy.
The average
fuel economy is viewed as a long-term
approximation
of your overall driving conditions.
If you press RESET in this mode while you’re driving,
the system will begin figuring fuel economy from that
point
in time.
2-73
ProCarManuals.com

Fuel
Press FUEL to see how much fuel has been used since
you last pressed the reset button. The display will show
a reading such as:
10.4 GALLONS USED or
39.4 LITERS USED
To learn how much fuel will be used from a specific
starting point, first press FUEL to display fuel used, then
press RESET.
Don’t confuse fuel used with the amount of fuel in your
tank.
Fuel Range
RANGE calculates the remaining distance you can drive
without refueling. It’s based on fuel economy and the
fuel remaining
in the tank. The display will show a
reading such as:
FUEL RANGE
235 MI or
FUEL RANGE
378 KM
If the range is less than 50 miles (80 km), the display
will read LOW
FUEL RANGE. The
fuel economy data used to determine fuel range
is
an average of recent driving conditions. As your driving
conditions change, this data is gradually updated.
Resetting
fuel range causes the fuel economy data to be
updated immediately.
To reset fuel range, press
RANGE, then RESET.
Average Speed
The calculation for average speed begins when SPEED
is reset. Press SPEED to display the average speed, such
as:
AVG SPEED
56 MPH or
AVG SPEED 90 KM/H
To reset the average speed, press SPEED and then
RESET.
ProCarManuals.com