1995 MITSUBISHI 3000GT engine removal

Downloaded from www.Manualslib.com manuals search engine 24GENERAL - Harness Connector Inspection
ess connector
contact pressure
checking harness
201 R057
Z16R1317
HARNESS CONNECTOR INSPECTION
CONNECTOR CONTINUITY AND VOLTAGE TESTWhen checking continuity and/or voltage at the waterproof
connectors, follow the steps below to avoid poor connector
contact and/or reduced waterproof performance of connectors.
(1) When checking is performed with the circuit in the stateof continuity, be sure to use the special tool (harness
connector).
Never insert a test bar from the harness side, because
to do so will reduce the waterproof performance and result
in corrosion.
(2) When the connector
JS disconnected for checking the fe-
male pin, the harness for checking the contact pressureof connector pins should be used.
Never force the insertion of a test bar, because to do
so will cause poor contact.(3) When the male pin is to be checked, apply the test bar
against the pin directly.
Care must be taken not to short-circuit the connector pins.
TERMINAL ENGAGEMENT CHECK
When the terminal stopper of connector is out of order, engage-
ment of male and female terminals becomes improper even
when the connector itself is engaged perfectly and the terminal
sometimes slips out to the rear side of connector. Ascertain,
therefore, that each terminal does not come off the connector
by pulling each harness wire.
CONNECTOR TERMINAL ENGAGEMENT AND
DISENGAGEMENTConnectors which are loose shall be rectified by removing
the female terminal from connector housing and raising its
lance to establish a more secure engagement. Removal of
connector terminal used for MFI and 4 A/l control circuit shallbe done in the following manner.
COMPUTER CONNECTOR(1) Insert screwdriver
[1.4 mm (.06 in.) width] as shown in
the figure, disengage front holder and remove it.
1 TSB Revision
IJ
I
I
I

Downloaded from www.Manualslib.com manuals search engine 16-12ENGINE ELECTRICAL - Charging System
GENERATORREMOVAL AND INSTALLATION
Pre-removal and Post-installation Operationl Removal and Installation of Right Bank Warm Up
Three-Way Catalytic Converter(Refer to GROUP 15-Exhaust Pipe, Main Mufflerand Catalytic Converter.)14-18ft.lbs.
l b
Removal steps
1. Air hose E 2. Air hose C
3. Suction hose clamo nuts
conditioning,4. Drive belt
(Refer to GROUP 11
-Engine Adjustment.)
216FO346
5. Generator connector
6. Heated oxygen sensor connector
7. Generator and generator bracket
assembly8. Generator bracket
9. Generator
lo-12 Nm7-9 ft.lbs.24 NmREMOVAL SERVICE POINT
dAbCLAMP NUT REMOVAL
On vehicles with an air conditioning, remove the clamp
nut, raise the suction hose and suspend it from the engine
hood using a cord.
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine 16-14ENGINE ELECTRICAL - Charging System
(From 1996 models)
Disassembly steps
+A,,A+ :: ~%? assembly3.Rear bearing4.Bearing retainer5.Front bearing6.Front bracket
45,7.Stator assembly
13
TEN0906
8. Plate9. Regulator and brush holder
10. Brush
11. Slinger
12. Rectifier assembly
13. Rear bracket
IDISASSEMBLY SERVICE POINT
dAbGENERATOR PULLEY REMOVAL
(1) Remove the bolts.
(2) Insert plain screwdriver between front bracket and
stator core and pry downward.
Caution
Do not insert screwdriver too deep, as there is
danger of damage to
stator coil.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Charging System16-15
WireZ6EN087!(3) Clamp the rotor in a vise with soft jaws.
(4) After removing the nut, remove the pulley and front
bracket from the rotor.
AB,STATOR / REGULATOR AND BRUSH HOLDER
REMOVAL
(1) When removing the stator, unsolder stator lead wirefrom the main diode of the rectifier.
(2) When removing the brush holder, unsolder it from
the rectifier.
Caution
(1) When soldering or unsoldering, be careful to
make sure that heat of soldering iron is not
transmitted to diodes for a long period. Finish
soldering or unsoldering in as short a time
as possible.
(2) Be careful that no undue force is exerted to
leads of diodes.REASSEMBLY SERVICE POINT
FAdROTOR ASSEMBLY INSTALLATION
Before rotor is attached to rear bracket, insert wire through
small hole made in rear bracket to lift brush. After rotor
has been installed, remove the wire.
3
TSB RevisionI
I

Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Starting System16-23
OPERATION
L
0For models equipped with the M/T, the clutch
pedal position switch contact is switched OFF
when the clutch pedal is depressed; when the
ignition switch is then switched to the “ST’ posi-tion, electricity flows to the starter relay and
the starter motor, the contact (magnetic switch)of the starter is switched ON and the starter
motor is activated.
NOTEIf the ignition switch is switched to the “ST
position without the clutch pedal being de-
pressed, electricity flows to the starter relay
(coil), the clutch pedal position switch (contacts)
and to ground, with the result that the contacts
of the starter relay are switched OFF, and, be-
cause the power to the starter motor is thereby
interrupted, the starter motor is not activated.lFor models equipped with the
AIT, when the
ignition switch is switched to the “ST’ position
while the selector lever is at the “P” or “N” posi-
tion, the contact (magnetic switch) of the starter
is switched ON and the starter motor is activated.
TROUBLESHOOTING HINTSThe starter motor does not operate at all.
l Check the starter (coil).
lCheck for poor contact at the battery terminals
and starter.l Check Park/Neutral position switch.
l Check clutch pedal position switch.
l Check starter relay.
l Check theft-alarm starter relay.
l Check key reminder switch.
i
/’
L&J
Fieldcoil wire
Iii?Stopper
IPinion gap
PinionZ6EL003
STARTER MOTORREMOVAL AND INSTALLATION
Refer to GROUP 22
- Manual Transaxle, or GROUP 23 -
Automatic Transaxle.INSPECTION
PINION GAP ADJUSTMENT(1) Disconnect field coil wire from M-terminal of magnetic
switch.
(2)Connect a 12 V battery between S-terminal and M-terminal.(3) Set switch to “ON”, and pinion will move out.
Caution
This test must be performed quickly (in less than 10
seconds) to prevent coil from burning.(4) Check pinion to stopper clearance (pinion gap) with a
feeler gauge.
Standard value: 0.5-2.0 mm (.020-,079 in.)
TSB Revision

Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Starting System16-27

27EN0628
1'0
Disassembly steps
1.Screw2.Magnetic switch3.Screw4.Starter cover5.Rear bracket6.Brush holder7.Brush8.Bush4A,9.Armature;y. Fap assembly
4A, .
12.Packing A13.Packing B
14.Plate
15.Planetary gear16.Lever4B, .A4 17. Snap ring4B, .A4 18. Stop ring19.Overrunning clutch20.Internal gear21. Planetary gear holder22.Front bracketDISASSEMBLY SERVICE POINTS
+A,ARMATURE / BALL REMOVAL
Caution
When removing the armature, be careful not to lose
the ball (which is used as a bearing) in the armature
end.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 16-28ENGINE ELECTRICAL - Starting System
Stop ringZ6EL0097
Z6ELOO96+B,SNAP
RING / STOP RING REMOVAL
(1) Press the stop ring, by using an appropriate socket,wrench, to the snap ring side.
(2)After removing the snap ring (by using snap-ring pliers),
remove the stop ring and the overrunning clutch.STARTER MOTOR PARTS CLEANING
1.Do not immerse parts in cleaning solvent. Immersing the
yoke and field coil assembly and/or armature will damage
insulation. Wipe these parts with a cloth only.
2.Do not immerse drive unit in cleaning solvent. Overrunning
clutch is pre-lubricated at the factory and solvent will wash
lubrication from clutch.3. The drive unit may be cleaned with a brush moistened
with cleaning solvent and wiped dry with a cloth.
REASSEMBLY SERVICE POINT
,A+TOP RING / SNAP RING INSTALLATION
Using a suitable pulling tool, pull overrunning clutch stop
ring over snap ring.INSPECTION
COMMUTATOR INSPECTION
(1) Place the armature on a pair of V-blocks, and check thedeflection by using a dial gauge.
Standard value: 0.05 mm (JO20 in.)
Limit: 0.1 mm
(.004 in.)
TSB Revision

Downloaded from www.Manualslib.com manuals search engine ENGINE ELECTRICAL - Ignition System16-45 l
IGNITION SYSTEM
LREMOVAL AND INSTALLATIONI
i
27EN0520
413 NmIlOft.lbs.
d
12 Nm
9 ft.lbs.
22 Nm16ftAbs.B678
W1
,A4
Removal stepsl Intake manifold plenum (Refer to
GROUP
1.5 - Intake Manifold.)1. Center cover
2. Spark plug cable
3. Spark plug
4. Ignition coil
5. Ignition power transistor
6. Crankshaft position sensor
cl 992 models>9 Nm
7
ft.lbs.u 16FO453
00662527
7. O-ring cl992 models>
8. Clamp Camshaft position sensor, Crankshaft
positionsensor removal steps models>l Timing belt cover (Refer to GROUP
11 - Timing Belt)
9. Camshaft position sensor
10. Crankshaft position sensor
TSB Revision