1995 LAND ROVER DISCOVERY service

76CHASSIS AND BODY
28
REPAIR REAR FOLD DOWN SEATS
Service repair no - 76.71.23
Seat and squab
Remove
1.Locate the seat in the down position, release the
seat belt strap and buckle from their stowed
positions.
2.Remove 4 Torx screws from the lower brackets.
3.Fold the seat up and remove the 2 Torx screws
from the upper brackets. Collect 4 washers.
4.Remove seat assembly.
Refit
5.Position seat assembly, align upper brackets,
and secure with Torx screws tightened to
13 Nm
(10 lbf ft)
.
NOTE: Ensure washers are fitted in their
correct positions.
6.Align lower brackets, fit Torx screws and tighten
to
13 Nm (10 lbf ft).
7.Secure the seat belt strap and buckle to their
stowed positions.
Seat squab
Remove
8.Remove the seat assembly from the vehicle.
9.Remove the pivot bolts and washers securing
the seat squab to the frame.
NOTE: The pivot bolts, securing the seat
squab and cushion, are fitted with a wavy
washer under the head and a plain washer
between the link or bracket. Ensure that these
washers are fitted in the correct locations when
reassembling the seat.

CHASSIS AND BODY
29
REPAIR 10.Remove the pivot bolts and washers securing
the hinge links to the seat squab.
11.If necessary remove the clips securing the cover
and detach the cover.
Refit
12.Reverse removal procedure.
Seat cushion
Remove
13.Remove the seat from the vehicle.
14.Remove the seat squab.
15.Remove the pivot bolts and washers securing
the hinge bracket and detach the bracket.
16.Invert the seat base and remove the screws and
rivets securing the base cover to the base.
17.Raise the seat base cover, to gain access to the
stay pivot bolts, remove the bolts and washers
and withdraw the stay and seat base cover.
18.If necessary remove the clips and detach the
cushion cover.
Refit
19.Reverse removal procedure.FRONT SEAT BELTS
Service repair no - 76.73.10
Remove
1.Move the front seat to the fully forward position
or tilt the seat forward (3 door vehicles).
2.Remove cover to gain access to the seat belt
upper mounting bolt.
NOTE: 3 door models have a
non-adjustable, upper mounting.
3.Remove the flanged securing bolt to release the
upper mounting and spacer.
4.Remove the cover and bolt securing the lower
mounting to the floor.
5.Detach the door seals from the 'B' post
sufficiently to allow removal of the lower trim
panel from the post.
6.Release the seat belt from the split section at the
top of the trim panel and withdraw the panel.
7.Remove the securing bolt and detach the inertia
reel from the bottom of the 'B' post.
5 door model illustrated

76CHASSIS AND BODY
30
REPAIR
8.Release the Torx bolt to allow removal of the
seat belt stalk assembly.
Refit
9.Reverse removal procedure.
NOTE: Ensure the seat belt is not twisted.
10.Finally, tighten the seat belt bolts to
32 Nm (24
lbf ft)
.REAR OUTER SEATS BELT
Service repair no - 76.73.18
Remove
1.Remove the rear fold down seat (if applicable).
See rear fold down seats.
2.Remove the speaker by releasing the screws
and disconnecting the Lucars. Withdraw the rear
quarter trim panel.
3.Remove the rear bodyside lower trim panel.
See
rear compartment lower trim panels.
4.Remove the bolts securing the brackets to the
wheel arch and upper bodyside.
5.Remove the bolt securing the inertia reel to the
bodyside and withdraw the seat belt.
6.Remove the seat belt buckle strap from the floor
mounted bracket.
See rear centre seat belt.
Refit
7.Reverse removal procedure.
8.Finally, tighten the seat belt bolts to
32 Nm (24
lbf ft)
.

CHASSIS AND BODY
31
REPAIR REAR CENTRE SEAT BELT
Service repair no - 76.73.20
Remove
1.Pull both halves of the seat belt through to the
rear of the seat.
2.Pull back the load space carpet to reveal the
Torx bolt heads.
3.Remove the Torx bolt and plain washer securing
the belt bracket to load space floor.
4.Remove belt complete with bracket.
5.Repeat steps 2 to 4 for other half of belt.
Refit
6.Reverse removal procedure.
7.Finally, tighten the seat belt bolts to
32 Nm (24
lbf ft)
.REAR FOLD DOWN SEAT BELTS
Service repair no - 76. 73.28
Remove
1.Remove the fold down seat or pocket side panel,
whichever is applicable.
See rear fold down
seats.
2.Remove speaker by releasing screws and
disconnecting Lucars. Withdraw rear quarter trim
panel.
3.Remove the rear bodyside lower trim panel.
See
rear compartment lower trim panels.
4.Remove the bolts securing the seat belt halves
to the body side.
Refit
5.Reverse removal procedure.
6.Finally, tighten the seat belt bolts to
32 Nm (24
lbf ft)
.

76CHASSIS AND BODY
32
REPAIR REAR GRAB HANDLE
Service repair no - 76.58.35
Remove
1.Remove speaker and rear quarter trim panel.
2.Detach the foam strip.
3.Remove the four securing bolts and detach the
handle.
Refit
4.Reverse removal procedure.

CHASSIS AND BODY
33
REPAIR WINGS [FENDERS]
Service repair no - 76.10.24
Remove
1.Disconnect battery negative lead.
2.Remove the headlamp surround.
3.Remove the front bumper assembly.
4.Remove the indicator repeater light.
5.Remove the four screws securing the wing
[fender] at the 'A' post.
6.Remove the bolts securing the bottom of the
wing [fender] at the bumper retaining bracket
and at the sill finisher.
7.If removing the RH wing [fender] loosen the
radio aerial securing nut.
8.Remove the seven bolts from the drain channel
in the top of the wing [fender].
9.Break the sealed joints at the valance and 'A'
post; then complete the removal of the wing
[fender]. If removing a RH wing withdraw the
wing [fender] sufficiently to allow removal of the
aerial before completing the removal.Cleaning/painting
10.Thoroughly clean all traces of existing sealant
from the sealing faces of the valance and 'A'
post.
11.Paint the cleaned surfaces with etch primer.
12.If the existing wing [fender] is to be refitted
repeat the cleaning and painting procedure on
the wing [fender] sealing surfaces.
Refit
13.Apply 3M 8572 Bolted Panel Sealer to the joint
faces on the valance and 'A' post and to the
bracket face.
14.Refit the wing [fender], on RH wings [fenders] fit
the radio aerial, and secure with the bolts and
screws ensuring that the wing [fender] correctly
aligns with the bonnet [hood].

76CHASSIS AND BODY
34
REPAIR SILL FINISHER
Service repair no - 76.76.05
Remove
1.Remove the nut, bolt and washer securing the
front of the sill finisher to the wing [fender]
support bracket.
2.Remove the screw securing the bracket at the
rear end of the finisher to the sill.
3.Using a suitable punch, remove the inserts from
the seven plastic retainers and withdraw the
finisher from the sill.
Refit
4.Reverse removal procedure. Using new plastic
retainers.BONNET [HOOD]
Service repair no - 76.16.01
Remove
1.Open the bonnet [hood] and support with the
stay.
2.Mark the position of the hinges to the bonnet
[hood].
3.With the assistance of a second operator,
remove the hinge to bonnet [hood] securing
screws, remove the support stay and lift bonnet
[hood] from the vehicle. Note the quantity of
shims fitted between the hinge and bonnet
[hood].
Refit
4.Reverse removal procedure. Ensuring that it
aligns with the wings [fenders], cowl panel and
front grille before fully tightening the securing
bolts.

CHASSIS AND BODY
35
REPAIR AIR INTAKE PLENUM COWL
Service repair no - 76.11.08
Remove
1.Remove the windscreen wiper arms.
2.Remove the securing nuts and the steel and
rubber washers from the wiper spindles.
3.Open the vehicle bonnet [hood].
4.Remove the rubber seal from the cowl flange.
5.Release the screen washer tubes from the
washer jets on the cowl.
6.Remove the centre bolt securing the cowl centre
section.
7.Remove the retainers securing the centre
section to the outer section.
8.Detach the centre section from the bulkhead.
9.Remove the nuts and bolts and detach the outer
sections of the cowl.Refit
10.Reverse removal procedure.