1995 LAND ROVER DISCOVERY service

CHASSIS AND BODY
59
REPAIR
9.Remove 5 trim studs securing trim panel.
10.Remove trim panel.
Refit
11.Fit and align trim panel.
12.Fit trim panel retaining studs.
13.Position load space cover mounting bracket and
secure with screws.
14.Fold rear seat squab back and secure to latch.
15.Position load space cover to mounting brackets
and secure.
16.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
17.Fit fold down rear seat belts.See rear fold
down seat belts - lh - with rear air
conditioning fitted.
18.Fit rear fold down seat.See rear fold down
seats.
'E' POST TRIM CASING - RH
Service repair no - 76.13.13/03
Remove
1.Remove rear speaker.
See ELECTRICAL,
Repair, rear speaker.
2.Release 2 'E' post finisher retaining studs from
alpine light trim.
3.Release 2 'E' post finisher retaining clips from
lower trim panel.
4.Remove 'E' post finisher.
Refit
5.Position 'E' post finisher clips to lower trim panel.
6.Secure 'E' post finisher studs to alpine light trim.
7.Fit rear speaker.
See ELECTRICAL, Repair,
rear speaker.

76CHASSIS AND BODY
60
REPAIR 'E' POST TRIM CASING - LH - WITH REAR AIR
CONDITIONING FITTED
Service repair no - 76.13.13/20
Remove
1.Remove rear speaker.
See ELECTRICAL,
Repair, rear speaker.
2.Release 2 trim casing retaining screw covers.
3.Remove 2 screws securing trim casing.
4.Remove trim casing.
Refit
5.Fit and align trim casing.
6.Fit and tighten screws securing trim casing and
fit covers.
7.Fit rear speaker.
See ELECTRICAL, Repair,
rear speaker.
ALPINE LIGHT TRIM CASING - LH - WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.13.20/20
Remove
1.Remove 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
2.Remove rear seat belt anchorage retaining bolt
cover.
3.Remove bolt securing rear seat belt anchorage.
4.Remove 2 trim studs securing trim casing.
5.Release trim casing from 2 retaining studs.
6.Remove trim casing.
Refit
7.Fit and align trim casing and secure with studs.
8.Fit 2 trim studs securing trim casing.
9.Position seat belt anchorage, fit bolt and tighten
to
20 Nm (15 lbf ft).
10.Fit cover to seat belt anchorage bolt.
11.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.

CHASSIS AND BODY
61
REPAIR REAR DOOR UPPER TRIM PANEL - WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.13.72/20
Remove
1.Remove alpine light trim casing.
See alpine
light trim casing - lh - with rear air
conditioning fitted.
2.Release 2 trim panel retaining screw covers.
3.Remove 2 trim panel retaining screws.
4.Release rear edge of trim panel from body.
5.Remove screw securing rear header duct to
alpine light duct.
6.Release rear header duct from alpine light duct.
7.Remove trim panel assembly.Dismantle
8.Remove 2 vents from trim panel.
9.Remove screw securing rear header duct to trim
panel.
10.Remove rear header duct.
Rebuild
11.Fit rear header duct to new trim panel and
secure with screw.
12.Fit vents to trim panel.
Refit
13.Position trim panel and connect rear header duct
to alpine light duct.
14.Fit and tighten screw securing rear header duct
to alpine light duct.
15.Secure rear edge of trim panel to body.
16.Fit and tighten screws securing trim panel.
17.Secure trim panel retaining screw covers.
18.Fit alpine light trim casing.
See alpine light
trim casing - lh - with rear air conditioning
fitted.

76CHASSIS AND BODY
62
REPAIR 'D' POST TRIM CASING - LH - WITH REAR AIR
CONDITIONING FITTED - 5 DOOR
Service repair no - 76.13.73/20
Remove
1.Remove rear compartment lower trim panel.
See rear compartment lower trim panel - lh -
with rear air conditioning fitted.
2.Remove the squab release button from control
rod.
3.Release rear seat belt from guide and remove
guide.
4.Remove the trim casing retaining stud.
5.Release trim casing from 2 retaining studs.
6.Remove trim casing.
Refit
7.Fit trim casing under alpine light trim, align and
secure retaining studs.
8.Fit trim casing retaining stud.
9.Position trim casing rear edge beneath sixth light
seal flange.
10.Fit seat belt to guide, align squab release control
rod and position guide to trim casing.
11.Fit squab release button to control rod.
12.Fit rear compartment lower trim panel.
See rear
compartment lower trim panel - lh - with rear
air conditioning fitted.

CHASSIS AND BODY
63
REPAIR SWITCH PACK - DASH PANEL CENTRAL LOUVRE
PANEL
Service repair no - 76.46.38
Remove
1.Release switch pack from louvre panel.
2.Disconnect 3 multiplugs from switch pack.
3.Remove switch pack.
Refit
4.Position switch pack.
5.Connect multiplugs to switch pack.
6.Secure switch pack to louvre panel.GRAB HANDLE
Service repair no - 76.58.30
Remove
1.Release 2 grab handle retaining screw covers.
2.Remove 4 screws securing grab handle to body.
3.Remove grab handle.
4.Collect 2 washers.
Refit
5.Position grab handle and washers.
6.Fit and tighten screws securing grab handle to
body.
7.Secure grab handle retaining screw covers.

76CHASSIS AND BODY
64
REPAIR GRAB HANDLE - TAIL DOOR - WITH REAR AIR
CONDITIONING FITTED
Service repair no - 76.58.35/20
Remove
1.Remove 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
2.Release foam strip from around grab handle
retaining bolts.
3.Remove 4 bolts securing grab handle to body.
4.Remove grab handle.Refit
5.Position grab handle, fit bolts and tighten to
10
Nm (7 lbf ft)
.
6.Secure foam strip to body.
7.Fit 'E' post trim casing.
See 'E' post trim
casing - lh - with rear air conditioning fitted.
HEADLINING - WITH SUN ROOF AND REAR AIR
CONDITIONING FITTED - 5 DOOR
Service repair no - 76.64.14/20
Remove
1.Remove both sun visors.
See sun visor.
2.Remove 4 grab handles.See grab handle.
3.Remove front headlining stowage panel.See
headlining stowage panel - front - with sun
roof fitted.
4.Remove LH alpine light trim casing.See alpine
light trim casing - lh - with rear air
conditioning fitted.
5.Remove RH alpine light trim casing.See alpine
light trim casing.
6.Release LH and RH sun visor clip retaining
screw covers.
7.Remove LH and RH sun visor clip retaining
screws.
8.Remove LH and RH clips.

CHASSIS AND BODY
67
REPAIR ASH TRAY - DASH PANEL CENTRAL LOUVRE
PANEL
Service repair no - 76.67.26
Remove
1.Open ash tray.
2.Press release catch and remove ash tray.
Refit
3.Fit ash tray.HEADLINING STOWAGE PANEL - FRONT - WITH
SUN ROOF FITTED
Service repair no - 76.67.27
Remove
1.Remove 10 screws securing stowage panel to
body.
2.Release panel and disconnect Lucar and 4
multiplugs.
3.Remove stowage panel assembly.

76CHASSIS AND BODY
68
REPAIR Dismantle
4.Remove interior lamp lens.
5.Remove 2 nuts securing lamp to stowage panel.
6.Remove lamp.
7.Remove alarm volumetric sensor/blanking plate.
8.Remove electric sun roof switch pack.
9.Remove electric sun roof manual opening plug.
Rebuild
10.Fit electric sun roof manual opening plug to
panel.
11.Fit alarm volumetric sensor.
12.Fit electric sun roof switch pack to panel.
13.Fit interior lamp to panel and secure with nuts.
14.Fit interior lamp lens.
Refit
15.Position stowage panel assembly and connect
Lucar and multiplugs.
16.Align panel to headlining and secure with
screws.REAR FOLD DOWN SEAT BELTS - LH WITH REAR
AIR CONDITIONING FITTED
Service repair no - 76.73.28/20
Remove
1.Locate the seat in the down position, remove the
seat belt strap and buckle from their stowed
positions.
2.Remove seat belt strap and buckle retaining bolt
covers.
3.Remove bolts securing strap and buckle.
4.Remove seat belts and collect spacers.
Refit
5.Fit spacers to seat belt retaining bolts, position to
fixings and tighten to
32 Nm (24 lbf ft).
6.Fit seat belt retaining bolt covers.
7.Secure seat belt strap and buckle to their stowed
positions and position seat in the up position.