1995 LAND ROVER DISCOVERY wheel

12ENGINE
18
REPAIR 10.Apply sealant to flywheel housing mating face on
cylinder block (Fig. J5944).
11.Fit housing to cylinder block and secure with
bolts as removed. Tighten to
45 Nm.
12.Remove surplus sealant from block.
13.Refit starter motor.
14.Refit flywheel.
See Flywheel
15.Refit clutch.See CLUTCH, Repair, Clutch
Assembly
16.Refit gearbox.See MANUAL GEARBOX,
Repair, R380 Manual Gearbox
17.Reconnect battery negative lead.OIL FILTER
Service repair no - 12.60.01
Remove
1.Place drain tray under filter.
2.Unscrew filter anti-clockwise, using a strap or
spanner.
Refit
3.Smear clean engine oil on seal of new filter.
4.Screw on filter until sealing ring touches
machined face, then tighten a further half turn by
hand only. Do not over tighten.

Tdi
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine block
Bearing cap 133...............................................................................................
Blanking plug, oil gallery, rear 37....................................................................
Oil squirt jet assembly 17................................................................................
Drain plug, cylinder block 25...........................................................................
Oil squirt jet, vacuum pump cam 7.................................................................
Connecting rod to cap 59................................................................................
Oil pick up assembly to bearing cap 9...........................................................
Oil pick up assembly to front cover 25............................................................
Camshaft thrust plate 9..................................................................................
Oil drain pipe to block (internal) 25.................................................................
Oil drain pipe to block (external) 25................................................................
Sump to cylinder block and front cover 25......................................................
Drain plug, oil sump 35...................................................................................
Tappet guide 14..............................................................................................
Breather side cover assembly 25....................................................................
Baffle plate to breather side cover 4..............................................................
Vacuum pump 25............................................................................................
Fuel lift pump 25.............................................................................................
Flywheel housing 45.......................................................................................
Flywheel housing clutch cover stud 10...........................................................
Plug, flywheel housing 12...............................................................................
Rear oil seal assembly 25...............................................................................
Oil filter adaptor 45..........................................................................................
Waxstat adaptor to oil filter adaptor 9............................................................
Oil pressure switch 17.....................................................................................
Oil filter, spin on 13.........................................................................................
Oil cooler unions to filter adaptor 45...............................................................
Oil level tube 25..............................................................................................
Engine mounting foot to cylinder block 85......................................................
Engine mounting foot to flywheel housing 45.................................................
Engine mounting foot rubber to mounting foot (bolt and nut) 85.....................
Flywheel to crankshaft 146..............................................................................
Clutch cover plate to flywheel 34....................................................................
Flex drive plate to crankshaft (auto) 146..........................................................
Flex drive plate to ring gear (auto) 25.............................................................
Flex drive plate to torque converter (auto) 45.................................................

12ENGINE
2
FAULT DIAGNOSIS ENGINE NOISES
Excessive or obtrusive noise from the engine
compartment originates from three main sources:
A. The exhaust system, which makes an
unmistakable and easy to diagnose noise.
B. External components emit the greatest variety of
noises, but are also easy to diagnose by simply
removing the drive belt.
C. Engine internal mechanical noises which can
vary in volume and pitch and may be a
combination of, tapping - knocking or rumbling,
are the most difficult to diagnose. The following
is therefore a guide to diagnosis of engine
internal mechanical noises only.
Engine internal mechanical noises.
Single or multiple, light tapping noise, particularly
when engine is cold.
See Description and
operation, Description
1.Is engine oil level correct?
NO - Top up to correct level.
See
LUBRICANTS, FLUIDS AND
CAPACITIES, Information,
Recommended Lubricants and Fluids
YES - Continue.
2.Is the lubricating pressure correct?
NO -
See Engine Oil Pressure Test
YES - Suspect valve operating mechanism.
3.To confirm diagnosis, remove the rocker covers
and with the engine idling, insert a feeler gauge
of 0,015mm between each rocker and valve
stem. A faulty valve operating mechanism will
emit a different noise when the feeler gauge is
inserted.
See Repair, Rocker Shaft Renew
Heavy knocking noise (particularly on load and
when engine is hot).
See Description and
operation, Description
1.Is engine oil level correct?
NO - Top up to correct level.
See
LUBRICANTS, FLUIDS AND
CAPACITIES, Information,
Recommended Lubricants and Fluids
YES - Continue.
2.Is the lubricating pressure correct?
NO -
See Engine Oil Pressure Test
YES - Drain engine oil and filter, and examine
for metallic contamination.
3.Is the oil contaminated with metal particles?
YES - Suspect faulty big end bearings. To
confirm diagnosis, short out the ignition to
each spark plug in turn. The noise will
disappear or be reduced when the
cylinder with the faulty big end is shorted
out.
4.If noise is not conclusively diagnosed, check the
security of the flywheel and crankshaft front
pulley. Temporarily release the drive belt to
reduce general noise level and use a
stethoscope to locate source of noise.
Heavy rumbling noise (particularly during hard
acceleration).
See Description and operation,
Description
1.Is engine oil level correct?
NO - Top up to correct level.
See
LUBRICANTS, FLUIDS AND
CAPACITIES, Information,
Recommended Lubricants and Fluids
YES - Continue.
2.Is the lubricating pressure correct?
NO -
See Engine Oil Pressure Test
YES - Drain engine oil and filter, and examine
for metallic contamination.
3.Is the oil contaminated with metal particles?
YES - Suspect faulty main bearings. If noise is
not conclusively diagnosed, check the
security of the flywheel and crankshaft
front pulley. Temporarily release the drive
belt to reduce general noise level and use
a stethoscope to locate source of noise.

12ENGINE
8
REPAIR CRANKSHAFT PULLEY ASSEMBLY
Service repair no - 12.21.01
1.Remove viscous coupling.
See COOLING
SYSTEM, Repair, Viscous Coupling, Fan
Blades, Pulley and Fan Cowl
2.Remove drive belt.See Drive Belt
3.Raise vehicle on ramp [hoist].
4.Remove bell housing bottom cover.
5.Remove engine undertray.
6.With assistance to stop flywheel rotation, remove
crankshaft pulley assembly retaining bolt.
7.Remove crankshaft pulley assembly.
8.If required: Place assembly in vice and remove
pulley.
9.Fit pulley to torsional vibration damper.
10.Lubricate seal face of assembly.
11.Fit pulley assembly.
12.With assistance to stop flywheel rotation, fit
retaining bolt. Tighten to
280 Nm.
13.Reverse removal procedure. 1 to 5.FRONT COVER OIL SEAL - RENEW
Service repair no - 12.21.14
1.Remove crankshaft pulley.
See Crankshaft
Pulley Assembly. Do not remove pulleys.
2.Remove eight screws and remove mud
excluder.
3.Fit button of 18G1328 to crankshaft, fit extractor
to seal.
4.Turn centre bolt of extractor to remove seal.
5.Remove seal from extractor.
6.Clean seal seating.
7.Lubricate outside diameter of seal.
8.Locate seal in front cover.
9.Fit adaptor 18G1291/5 to 18G1291/4.
10.Fit tool to seal.
11.Fit and tighten centre bolt to crankshaft, tighten
centre locknut to seat seal.
12.Slacken locknut and remove tool.
13.Lubricate seal lip.
14.Fit mud excluder and tighten screws.
15.Fit crankshaft pulley assembly.

12ENGINE
10
REPAIR TIMING CHAIN AND CHAINWHEELS
Service repair no - 12.65.12
Remove
1.Remove front cover.
See Front Cover Gasket
2.Remove retaining bolt and washer, remove
distributor drive gear and spacer.
3.Ensure number one piston is at TDC.
4.Remove chainwheels and chain as an assembly.
See V8i Overhaul Manual.
Refit
5.Clean chainwheels and chain.
6.Fit chainwheels to chain, aligning timing marks.
7.Ensure camshaft key is fitted parallel to shaft
axis to ensure adequate lubrication to distributor
drive gear.
8.Engage chainwheel assembly on camshaft and
crankshaft keys, ensure chain wheels are fully
located.
9.Check alignment of timing marks with straight
edge.
10.Fit spacer with flange to front,
11.Fit distributor drive gear with groove towards
spacer.
12.Fit retaining bolt and washer. Tighten to
58 Nm.
13.Fit front cover.See Front Cover Gasket
FLYWHEEL
Service repair no - 12.53.07
Remove
1.Remove gearbox and clutch.
See CLUTCH,
Repair, Clutch Assembly
2.Loosen starter motor bolts.
3.Lock flywheel, remove flywheel bolts and
flywheel.
Refit
4.Clean components for reassembly.
5.Fit flywheel.
6.Clean threads, apply Loctite 270 to threads.
7.Lock flywheel, fit flywheel bolts. Tighten to
80
Nm.

V8i
11
REPAIR FLEXIBLE DRIVE PLATE AND RING GEAR
Service repair no - 12.53.13
Remove
1.Remove transmission.
See AUTOMATIC
GEARBOX, Repair, LT230T Transfer Gearbox
with Automatic Gearbox Assembly - V8i
2.Remove flexible drive plate and ring gear
assembly.
See V8i Overhaul Manual.
Refit
3.Clean all components for reassembly.
4.Fit ring gear and flexible drive plate assembly.
See V8i Overhaul Manual.
5.Fit transmission.CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
1.Automatic transmission, remove drive plate.
See Flexible Drive Plate and Ring Gear
OR manual transmission, remove flywheel.See
Flywheel
2.Remove sump.See Oil Sump
3.Remove rear main bearing cap.
4.Remove cross seals from cap.
5.Remove crankshaft rear oil seal.
6.Clean main bearing cap and oil seal area of
block.
7.Fit new cross seals to bearing cap.
8.Apply Hylomar SQ32M to block as illustrated.
9.Lubricate bearing shell and cross seals using
clean engine oil.
10.Fit bearing cap, do not tighten bolts.
11.Ensure cap is fully home and seated squarely on
the block.

12ENGINE
12
REPAIR
12.Ensure service tools LRT-12-010 and
LRT-12-091 are scrupulously clean. Coat seal
guide and oil seal journal with clean engine oil.
CAUTION: Do not handle oilseal lip, check
it is not damaged. Ensure outside diameter
remains clean and dry.
13.Position oil seal guide LRT-12-010 on crankshaft
flange.
NOTE: Lubricant coating must cover seal
guide outer surface completely to ensure
that oil seal lip is not turned back during
assembly. Position oil seal, lipped side towards
engine, on seal guide. Seal outside diameter
MUST be clean and dry.
14.Fit oil seal using tool LRT-12-091. Remove seal
guide.
15.Tighten rear main bearing cap to
90 Nm.
16.Fit sump.
17.Fit flywheel or flexible drive plate and ring gear.ENGINE
Service repair no - 12.41.01
Remove
1.Park vehicle on level ground and apply park
brake.
2.De-pressurise fuel system.
See FUEL
SYSTEM, Repair, Depressurising Fuel
System
3.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
4.Remove battery.See ELECTRICAL, Repair,
Battery
5.Remove radiator/oil coolers.See COOLING
SYSTEM, Repair, Radiator/Oil Coolers
6.Place an absorbent cloth around fuel feed hose
at fuel rail and release compression nut.
Remove feed hose from rail, seal end of pipes
with masking tape to prevent ingress of dirt.
7.Release fuel return hose clamp and remove
hose from pressure regulator, seal both
openings with masking tape to prevent ingress of
dirt.
8.Remove vacuum hose from rear of regulator.
9.Manual vehicles: Disconnect throttle cable from
bracket. Automatic vehicles: Detach throttle
bracket from plenum chamber and lay assembly
to one side.
See FUEL SYSTEM, Repair,
Plenum Chamber DO NOT DISTURB KICK
DOWN CABLE SETTING.
10.Remove ram housing.See FUEL SYSTEM,
Repair, Ram Housing
11.Remove air flow sensor.See FUEL SYSTEM,
Repair, Air Flow Sensor
12.Remove air cleaner assembly.See FUEL
SYSTEM, Repair, Air Cleaner Assembly
13.Remove Generator.See ELECTRICAL,
Description and operation, Generator
14.Release air conditioning compressor from its
mounting and lay to one side. DO NOT
discharge air conditioning system.
See AIR
CONDITIONING, Repair, Compressor

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine
Adaptor plate to crankshaft 84........................................................................
Generator and power steering mounting bracket to cylinder head 30............
Cylinder head:
Stage 1: 20.............................................................................................
Stage 2: - Further 180°±5°
Drive plate to converter 39..............................................................................
Engine mountings to engine and chassis 55..................................................
Engine mounting rubbers to brackets 30........................................................
Flexible drive plate to crankshaft adaptor plate 41.......................................... **
Flywheel to crankshaft bolts 78....................................................................... **
Lifting eye to cylinder heads 39......................................................................
Main bearing cap rear bolts 92....................................................................... *
Oil sump drain plug 40....................................................................................
Oil sump to cylinder block 18..........................................................................
Rocker cover to cylinder head 9....................................................................
Rocker shaft bracket to cylinder head 38........................................................
Spark plug 21..................................................................................................
Starter motor attachment 44...........................................................................
* These bolts must have threads coated in lubricant EXP16A before assembly.
** These bolts must have threads coated in sealant Loctite 270
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.