1995 LAND ROVER DISCOVERY maintenance

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

V8i
5
DESCRIPTION AND OPERATION Distributor and timing chain lubrication
The distributor and timing chain are lubricated from
the camshaft front bearing. The feed to the timing
chain is channelled along the camshaft sprocket, key
and spacer where it sprays onto the chain.
1. Bearing
2. Camshaft
3. Key
4. Camshaft timing chain sprocket
5. Spacer
6. Distributor drive gearHydraulic tappets
1. Clip
2. Pushrod seat
3. Inner sleeve
4. Upper chamber
5. Non-return ball valve
6. Spring
7. Outer sleeve
8. Lower chamber - high pressure
The purpose of the hydraulic tappet is to provide
maintenance free and quiet operation of the inlet and
exhaust valves. It achieves its designed purpose by
utilizing engine oil pressure to eliminate the
mechanical clearance between the rockers and the
valve stems.
During normal operation, engine oil pressure present
in the upper chamber 4, passes through the
non-return ball valve 5 and into the lower (high
pressure) chamber 8.
When the cam begins to lift the outer sleeve 7, the
resistance of the cylinder valve spring felt through the
pushrod seat 2, causes the inner sleeve 3, to move
downwards inside the outer. This slight downward
movement of the inner sleeve closes the ball valve 5
and increases the hydraulic pressure in the high
pressure chamber, sufficient to ensure that the push
rod opens the valve fully.
As the tappet assembly moves off the peak of the cam
the ball valve 5 opens to equalize the pressure in both
chambers which ensures that the valve fully closes
when the tappet is on the back of the cam.

V8i
15
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Drain engine oil
See SECTION 10,
Maintenance, Under Vehicle Maintenance
2.Fit drain plug. Tighten to40 Nm.
3.If fitted, disconnect low oil level sensor multiplug.
4.Remove bolt securing dipstick tube to rocker
cover.
5.Working form the centre outwards, progressively
loosen and remove 17 bolts securing sump.
Remove sump.
6.Remove all traces of sealant from mating
surfaces of sump, cylinder block and front cover,
using a suitable solvent or plastic scraper.
7.Degrease mating surfaces of sump, cylinder
block and front cover.Refit
8.Apply RTV Hylosil White sealant to mating
surface of sump.
9.Position sump, tighten bolts finger tight.
10.Tighten bolts progressively in sequence shown.
Tighten to
18 Nm.
11.Fit bolt securing dipstick tube to rocker cover.
12.If fitted, connect low oil level sensor multiplug.

Mpi
1
REPAIR CAMSHAFT FRONT OIL SEAL
Service repair no - 12.13.07 - Exhaust
Service repair no - 12.13.09 - Inlet
Remove
1.Disconnect battery negative lead.
2.Remove drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove 5 bolts, timing belt upper cover.
4.Remove timing belt upper cover.
5.Remove 5 bolts, timing belt centre cover.
6.Remove timing belt centre cover.
7.Rotate crankshaft to align camshaft gear timing
marks - 90°B.T.D.C.
8.Fit tool LRT-12-058 to lock flywheel.
9.Fit tool LRT-12-060 to lock camshaft gears.
10.Loosen camshaft belt tensioner bolt.
11.Move tensioner away from belt and tighten
tensioner bolt.
12.Remove belt from camshaft gears.

Mpi
3
REPAIR
For torque values.See Specifications, torque,
Torque Values
3.Fit timing belt upper backplate and tighten bolts
to the correct torque.
4.Fit camshaft gears noting the 'IN' and
'EXHAUST' identifying marks.
5.Fit, but do not tighten, camshaft gear centre
bolts.
6.Ensure timing marks are aligned.
7.Fit camshaft locking tool LRT-12-060.
8.Tighten camshaft gear bolts to the correct
torque.
9.Fit timing belt.
See Camshaft Drive Belt
10.Adjust timing belt tension.
11.Remove tool LRT-12-058 from flywheel.
12.Fit timing belt centre cover and tighten bolts to
correct torque.
13.Fit timing belt upper cover and tighten bolts to
correct torque.
14.Fit drive belt.
See SECTION 10, Maintenance,
Under Bonnet [Hood] Maintenance
15.Reconnect battery negative lead.INLET - EXHAUST CAMSHAFT REAR OIL PLUG
Remove
1.Remove cylinder head.
2.Lever out, camshaft rear oil seal plug.
Refit
1.Clean plug housing.
2.Fit new plug applying force to outer edge only.
3.Refit cylinder head.

12ENGINE
6
REPAIR ENGINE
Service repair no - 12.41.01
Remove
1.Site vehicle onto ramp [hoist].
2.Remove the drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator - Mpi
4.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
5.Drain engine oil.
6.Position absorbent cloth around fuel pipe to fuel
rail union.
Unscrew union to relieve pressure.
CAUTION: Plug the connections
7.Release clip and disconnect hose from coolant
pump.
8.Release clip and disconnect hose from heater
rail.

EMISSION CONTROL
1
FAULT DIAGNOSIS REV: 09/95 TESTING EVAPORATIVE EMISSION CONTROL -
PRE ADVANCED EVAPS
The following pressure test procedure is intended to
provide a method for ensuring that the system does
not leak excessively and will effectively control
evaporative emissions.
Equipment required.
Nitrogen cylinder (compressed air may be used to
pressure the system when there has NEVER been
fuel present in the fuel or evaporative control
systems).
Water manometer (0 - 30" H2O or more).
Pipework and a "T" piece.
Method.
1.Ensure that there is at least two gallons of fuel in
the petrol tank unless there has never been any
fuel in the system.
2.Disconnect, at the adsorption canister, the pipe
to the vapour separator.
3.Connect this pipe to the nitrogen cylinder and
the water manometer using the "T" piece.
4.Pressurize the system to between 26.5 and 27.5
inches of water, allow the reading to stabilize,
then turn off the nitrogen supply.
5.Measure the pressure drop within a period of 2
minutes 30 seconds. If the drop is greater than
2.5 inches of water the system has failed the
test. Note that a fully sealed system will show a
slight increase in pressure.
6.Should the system fail the test, maintain the
pressure in the system and apply a soap
solution round all the joints and connections until
bubbles appear to reveal the source of the leak.
7.Repeat the test and if successful, dismantle the
test equipment and reconnect the pipe to the
adsorption canister.LEAK DETECTION PROCEDURE - ADVANCED
EVAPS
1.Connect TestBook to the vehicle and confirm
that the fault code(s) displayed relate to an
EVAP system fault.
2.Examine components in fuel and EVAP system
for damage or poorly connected joints.
3.Repair or replace components to rectify any
faults found, then reset the Check Engine light
using TestBook.
4.Carry out Drive Cycle,
See Drive Cycle -
Advanced EVAPS
5.Using TestBook confirm that the Evaporative
Loss Control (ELC) Inspection and Maintenance
(IM) flag has cleared. This procedure should
confirm that the ELC test was carried out during
the drive cycle and that the fault was cured.
6.If the IM flag is still shown, use TestBook to
interrogate the engine management system to
ascertain which of the following situations exists:
·If a fault code is shown then further investigation
is required, proceed to the next step.
·If the IM flag is still shown, but no faults are
indicated the conditions for the ELC check have
not been met and the drive cycle must be
repeated.
7.Connect the Leak Detection/EVAP Diagnostic
Station to the vehicle and carry out the
procedures given in the operating instructions
supplied with the equipment.
8.Rectify faults indicated by the Leak
Detection/EVAP Diagnostic Station and return to
step 4.

R380
1
REPAIR R380 MANUAL GEARBOX
Service repair no - 37.20.02
Remove
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
1.Install vehicle on a ramp [hoist].
2.Disconnect battery earth lead.
3.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
4.Remove sound insulation from top of
transmission tunnel.
5.Remove bolt and remove upper gear lever.
6.Remove screws securing gear selector lever and
high/low selector lever draft excluders.
7.Remove draft excluder clamp rings.
8.Remove handbrake cable clevis pin clip and
clevis pin.
9.Remove 'C' clip and cable adjuster.
10.Select low range to prevent gear lever fouling
tunnel when removing gearbox.
11.Remove bolt securing gearbox breather pipe clip
to cylinder block.
12.Remove bolts securing fan cowl to radiator.
13.Release fan cowl from radiator and lay over fan
blades.
14.Raise ramp [hoist].
15.Drain oil from main gearbox and transfer
gearbox.
See SECTION 10, Maintenance,
Under Vehicle Maintenance
16.Remove exhaust front pipe(s).See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
System Complete
17.Release intermediate exhaust pipe(s) from
mountings and tie aside.
18.Remove bolts securing clutch slave cylinder.
19.Release slave cylinder from clutch housing and
collect spacer.
20.Mark propeller shaft drive flange relationships for
reassembly.
21.Disconnect front and rear propeller shafts from
transfer gearbox. Tie shafts aside.
22.Remove clamp and disconnect speedometer
cable from transfer gearbox.
23.Release handbrake cable from transmission
tunnel.
24.Temporarily support transmission in a way which
enables the crossmember to be removed and a
hoist cradle to be fitted.