1995 LAND ROVER DISCOVERY ECU

Tdi
3
REPAIR ENGINE
Service repair no - 12.41.01
Remove
CAUTION: Seal all exposed pipe ends
against ingress of dirt after disconnection.
1.Park vehicle on level ground and apply park
brake.
2.Disconnect battery negative lead.
3.Remove bonnet [hood].
See CHASSIS AND
BODY, Repair, Bonnet [Hood]
4.If air conditioning is fitted, remove RH footwell
side trim panel and disconnect harness multiplug
from relay.
5.Disconnect the two engine harness multiplugs
on LH side of footwell.
6.Remove engine harness grommet from
bulkhead and move harness into engine bay.
7.Release battery positive lead from retaining clip
at base of suspension turret.
8.Remove Radiator Assembly.
See COOLING
SYSTEM, Repair, Radiator
9.Discharge air conditioning system.See AIR
CONDITIONING, Adjustment, Refrigerant
Recovery Recycling Recharging
Remove retaining bolts and disconnect both pipe
adaptors from rear of compressor.
10.Remove rocker cover insulation.
11.Disconnect cyclone hose from air cleaner hose.
12.Remove air cleaner hose from turbocharger.
13.Remove feed pipe/hose from turbocharger and
intercooler.
14.Disconnect heater hoses from cylinder head and
heater rails.
15.Remove bolt securing transmission breather
pipe clip to cylinder head; move breather pipes
aside.
16.Disconnect inlet and outlet hoses from power
steering pump.
17.Disconnect bypass hose from thermostat
housing.
18.Release bypass hose from retaining clips on
front timing cover.
19.Remove split pin securing inner throttle cable to
injector pump.
20.Depress tags on outer cable adjusting nut,
remove cable from mounting bracket, and move
aside.
21.If automatic transmission is fitted, release
kickdown cable from injector pump and mounting
bracket.

12ENGINE
4
REPAIR 22.Disconnect feed pipe and spill return pipe from
injector pump.
23.Disconnect both pipes from fuel lift pump.
24.Disconnect servo hose from vacuum pump.
25.Remove three retaining nuts and disconnect
exhaust down pipe.
26.Remove oil cooler pipes from oil filter adaptor.
27.If automatic transmission is fitted, disconnect
feed and return pipes at gearbox oil cooler.
Remove retaining bracket from LH side of
cylinder block and release both oil cooler pipes.
28.Support gearbox.
29.Disconnect ground strap from starter motor.
30.On vehicles with automatic transmission, remove
fixings and detach drive plate housing access
panel and gasket.31.Working through drive plate housing aperture
mark the torque convertor and drive plate to
facilitate reassembly.
32.Remove the four convertor to flexible drive
securing bolts, rotating crankshaft to gain access
to each individual bolt.
33.Fit engine lifting bracket to the two RH rear
cylinder head fixing bolts.
34.Using suitable hoist, fit lifting chains to engine.
35.Remove four bolts, from both sides, securing
front engine mounting brackets to cylinder block.
36.Remove two bolts, from both sides, securing
front engine mounting bracket to bell housing.

Tdi
5
REPAIR
37.Remove nuts and plain washers securing front
engine mountings to chassis,and lift both engine
mounting bracket assemblies from vehicle.
38.Remove engine to bell housing fixings. Leave
starter motor attached.
39.Raise engine to separate from transmission.
40.Check all connections to engine have been
disconnected.
41.Remove engine.Refit
42.Apply Hylomar to mating faces of bell housing.
Lubricate splines of gearbox primary pinion with
Rocol MV 3.
If automatic transmission, coat the four drive
plate to torque convertor bolts with Loctite 290.
Tighten to
39 Nm.
43.Lower engine and locate with transmission.
If manual transmission locate primary pinion into
clutch and engage bell housing dowels. Fit
engine to bell housing fixings. Tighten to
40 Nm.
If automatic transmission fixings. Tighten to46
Nm.
44.Raise engine, refit front engine mounting
brackets to cylinder block and bell housing.
45.Remove gearbox support and lower engine.
46.Tighten front engine mountings to chassis
fixings. Tighten to
45 Nm.
47.Reverse removal procedure. 1 to 37.

12ENGINE
6
REPAIR CRANKSHAFT PULLEY
Service repair no - 12.21.01
Remove
1.Disconnect battery negative lead.
2.Drain coolant.
3.Remove top hose from radiator.
4.Remove intercooler to induction manifold hose.
5.Remove viscous fan and coupling.
See
COOLING SYSTEM, Repair, Viscous
Coupling, Fan Blades, Pulley and Fan Cowl
6.Remove fan cowl.
7.Remove drive belt.
See Drive Belt Renew
8.Fit crankshaft pulley retainer LRT-12-080 and
secure with four bolts.
9.Remove crankshaft pulley retaining bolt using
socket and suitable long bar.
10.Remove pulley retainer.
11.Remove pulley, if necessary using extractor
LRT-12-049 with thrust pad from LRT-12-031.Refit
12.Refit in reverse order, lightly greasing pulley
spigot. Tighten to
80 Nm + 90°.

Tdi
7
REPAIR FRONT COVER PLATE
Service repair no - 12.65.01
Remove
1.Disconnect battery negative lead.
2.Drain coolant.
3.Remove top hose from radiator.
4.Remove inter-cooler to induction manifold hose.
5.Remove viscous coupling and fan.
See
COOLING SYSTEM, Repair, Viscous
Coupling, Fan Blades, Pulley and Fan Cowl
6.Remove fan cowl.
7.Remove drive belt.
See Drive Belt Renew
8.Remove crankshaft pulley.See Crankshaft
Pulley
9.Remove 14 bolts securing front cover plate,
noting top two bolts also retain thermostat hose
clips.
10.Remove cover plate complete with gasket.
11.Remove small gasket from centre bolt boss.
Seal replacement
12.Remove worn seal from cover and clean recess.
13.Support cover and fit new seal, open side fitted
into recess, using special tool LRT-12-077.
Refit
14.Refit in reverse order to removal using new
gaskets, fitting the securing bolts as shown in
illustration ST3475. Tighten to
25 Nm.

Tdi
9
REPAIR Belt tensioner
NOTE: The belt tensioner need only be
removed if it is being replaced or for
access purposes to remove front cover.
11.Remove securing bolt and withdraw tensioner
complete with spacer.
Crankshaft gear/front cover oil seal
12.If the crankshaft gear cannot be removed by
hand, use special tool LRT-12-078 with main
body and thrust button from special tool
LRT-12-031 as illustrated ST3478M. Withdraw
gear complete with 'O' ring seal.
13.If necessary prise out oil seal from front cover.
14.Lubricate a new crankshaft oil seal with clean
engine oil.
15.With lip side leading, drive-in seal squarely using
special tool LRT-12-079.
16.Lubricate new 'O' ring seal with petroleum jelly
and slide onto shaft, taking care not to damage
seal on the woodruff keys.
17.Fit crankshaft gear, tap fully home ensuring 'O'
ring seal is properly seated.
CAMSHAFT GEAR/FRONT COVER OIL SEAL
Service repair no - 12.13.05
18.Remove centre bolt from camshaft gear and
withdraw gear.
19.Remove existing oil seal from front cover using
special tool LRT-12-038.
20.Lubricate a new camshaft oil seal with clean
engine oil.

12ENGINE
10
REPAIR
21.With lip side leading, drive-in seal squarely using
special tool LRT-12-082.
22.Refit gear.
FUEL INJECTION PUMP GEAR
Service repair no - 19.30.06
Remove
23.Slacken the three bolts on front of gear.
CAUTION: It is important to ensure that
when the injection pump is locked no
attempt must be made to rotate it. Take
care not to allow the crankshaft to be turned.24.Remove special tool pin from gear.
25.Remove three bolts and withdraw plate and
gear.
Refit
26.Fit gear and plate and secure with three bolts.
27.Insert pin from special tool LRT-12-045 in
injection pump gear and through into pump
flange.

Tdi
11
REPAIR Timing belt fitting and tensioning
NOTE: It is important that belt tensioning
is carried out carefully and accurately. The
following procedure involves tensioning
the belt twice to ensure that it is equally tensioned
between each gear. New and original belts are
tensioned to different figures.
28.Ensure timing marks are correctly aligned, pin
from special tool LRT-12-045 is correctly
inserted in injection pump gear and timing tool
LRT-12-044 (LRT-12-085 if EDC) is fitted to
flywheel housing with pin located in flywheel slot.
Or if automatic: Timing tool LRT-12-044 is fitted
to engine backplate and pin located in ring gear.
29.Fit belt observing rotational marks made during
removal. Feed belt over gears keeping it tight on
drive side.
30.Fit idler pulley.
31.Slacken injection pump gear retaining bolts.
32.Adjust belt to correctly sit in gears.
33.Slacken belt tensioner securing bolt to finger
tight.
34.Insert 13 mm square drive extension bar in
tensioner plate.
NOTE: Belt tensioning should be carried
out using a dial type torque meter having a
range not exceeding
60 Nm.The torque
meter should be used in the almost vertical
position.
35.Apply a tension of
14 to 16 Nmfor a new belt or
11 to 13 Nmfor an original belt. When tension
is correct tighten clamp bolt.
36.Tighten injection pump gear bolts.
37.Remove pin from injection pump gear.
38.Disengage timing pin from timing slot in flywheel
or ring gear.
39.Rotate crankshaft one and three quarter turns in
a clockwise direction; then continue rotation until
timing pin in timing tool can be engaged with slot
in flywheel or ring gear.
40.Disengage timing pin.
41.Insert pin from special tool LRT-12-045 in
injection pump gear and through into pump
flange.
42.Slacken injection pump gear retaining bolts.
43.Slacken tensioner and retension belt.
44.Tighten injection pump gear retaining bolts.
45.Remove pin from injection pump gear.
46.Remove timing tool and refit plug.
47.Fit front cover plate using new gaskets.
See
Front Cover Plate