1995 LAND ROVER DISCOVERY wheel bolts

V8i
11
REPAIR FLEXIBLE DRIVE PLATE AND RING GEAR
Service repair no - 12.53.13
Remove
1.Remove transmission.
See AUTOMATIC
GEARBOX, Repair, LT230T Transfer Gearbox
with Automatic Gearbox Assembly - V8i
2.Remove flexible drive plate and ring gear
assembly.
See V8i Overhaul Manual.
Refit
3.Clean all components for reassembly.
4.Fit ring gear and flexible drive plate assembly.
See V8i Overhaul Manual.
5.Fit transmission.CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
1.Automatic transmission, remove drive plate.
See Flexible Drive Plate and Ring Gear
OR manual transmission, remove flywheel.See
Flywheel
2.Remove sump.See Oil Sump
3.Remove rear main bearing cap.
4.Remove cross seals from cap.
5.Remove crankshaft rear oil seal.
6.Clean main bearing cap and oil seal area of
block.
7.Fit new cross seals to bearing cap.
8.Apply Hylomar SQ32M to block as illustrated.
9.Lubricate bearing shell and cross seals using
clean engine oil.
10.Fit bearing cap, do not tighten bolts.
11.Ensure cap is fully home and seated squarely on
the block.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Engine
Adaptor plate to crankshaft 84........................................................................
Generator and power steering mounting bracket to cylinder head 30............
Cylinder head:
Stage 1: 20.............................................................................................
Stage 2: - Further 180°±5°
Drive plate to converter 39..............................................................................
Engine mountings to engine and chassis 55..................................................
Engine mounting rubbers to brackets 30........................................................
Flexible drive plate to crankshaft adaptor plate 41.......................................... **
Flywheel to crankshaft bolts 78....................................................................... **
Lifting eye to cylinder heads 39......................................................................
Main bearing cap rear bolts 92....................................................................... *
Oil sump drain plug 40....................................................................................
Oil sump to cylinder block 18..........................................................................
Rocker cover to cylinder head 9....................................................................
Rocker shaft bracket to cylinder head 38........................................................
Spark plug 21..................................................................................................
Starter motor attachment 44...........................................................................
* These bolts must have threads coated in lubricant EXP16A before assembly.
** These bolts must have threads coated in sealant Loctite 270
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................
NOTE: Torque values above are for all screws and bolts used except for those specified.

12ENGINE
4
DESCRIPTION AND OPERATION CYLINDER BLOCK COMPONENTS
1. Cylinder block
2. Knock sensor
3. Crankshaft sensor
4. Bolt - crankshaft sensor
5. Locating dowel - cylinder head
6. Bolt - connecting rod
7. Piston
8. Piston ring - top compression
9. Piston ring - 2nd compression
10. Piston ring - oil control
11. Gearbox adapter plate
12. Bearing shell - big end - upper
13. Flywheel
14. Bolt - flywheel
15. Torx screw - gearbox adapter plate
16. Blanking plate
17. Bolt - blanking plate
18. Gasket
19. Bolt - crankshaft rear oil seal housing
20. Crankshaft rear oil seal and housing
21. Bolt - coolant pump cover
22. Coolant pump cover
23. Impeller
24. Sealing rings
25. 'O' ring
26. Bolts - coolant pump
27. 'O' ring
28. Coolant pump body
29. Thrust washer halves - upper
30. Bearing shell - main bearing - upper
31. Locating dowel - oil pump
32. Locating dowel - flywheel
33. Gudgeon pin34. Crankshaft
35. Bearing shell - big end - lower
36. Bearing cap - big end
37. Nut - big end bearing cap
38. Locating dowel - main bearing cap
39. Bearing caps - main bearings
40. Bolt - main bearing cap
41. Thrust washer halves - lower
42. Bearing shell - main bearing - lower
43. Woodruff keys
44. Dipstick
45. Bolt - dipstick tube
46. Dipstick tube
47. Bolts - sump
48. Gasket - sump
49. 'O' ring
50. Oil strainer
51. Bolts - oil strainer
52. Sump
53. Washer - drain plug
54. Drain plug
55. Oil filter element
56. Crankshaft front oil seal
57. Bolts - oil pump
58. Gasket - oil pump
59. Oil pump
60. Oil pressure switch
61. Crankshaft spigot bush
62. Crankshaft spigot bearing
63. Locating dowel - coolant pump
64. Connecting rod
65. Bolts belt tensioner mounting plate
66. Belt tensioner mounting plate
67. Bolt - gearbox adapter plate

Mpi
1
REPAIR CAMSHAFT FRONT OIL SEAL
Service repair no - 12.13.07 - Exhaust
Service repair no - 12.13.09 - Inlet
Remove
1.Disconnect battery negative lead.
2.Remove drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove 5 bolts, timing belt upper cover.
4.Remove timing belt upper cover.
5.Remove 5 bolts, timing belt centre cover.
6.Remove timing belt centre cover.
7.Rotate crankshaft to align camshaft gear timing
marks - 90°B.T.D.C.
8.Fit tool LRT-12-058 to lock flywheel.
9.Fit tool LRT-12-060 to lock camshaft gears.
10.Loosen camshaft belt tensioner bolt.
11.Move tensioner away from belt and tighten
tensioner bolt.
12.Remove belt from camshaft gears.

Mpi
3
REPAIR
For torque values.See Specifications, torque,
Torque Values
3.Fit timing belt upper backplate and tighten bolts
to the correct torque.
4.Fit camshaft gears noting the 'IN' and
'EXHAUST' identifying marks.
5.Fit, but do not tighten, camshaft gear centre
bolts.
6.Ensure timing marks are aligned.
7.Fit camshaft locking tool LRT-12-060.
8.Tighten camshaft gear bolts to the correct
torque.
9.Fit timing belt.
See Camshaft Drive Belt
10.Adjust timing belt tension.
11.Remove tool LRT-12-058 from flywheel.
12.Fit timing belt centre cover and tighten bolts to
correct torque.
13.Fit timing belt upper cover and tighten bolts to
correct torque.
14.Fit drive belt.
See SECTION 10, Maintenance,
Under Bonnet [Hood] Maintenance
15.Reconnect battery negative lead.INLET - EXHAUST CAMSHAFT REAR OIL PLUG
Remove
1.Remove cylinder head.
2.Lever out, camshaft rear oil seal plug.
Refit
1.Clean plug housing.
2.Fit new plug applying force to outer edge only.
3.Refit cylinder head.

Mpi
5
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1.Remove gearbox.
2.Remove clutch assembly.
3.Remove flywheel.
4.Drain engine oil.
5.Fit sump plug, replacing sealing washer if
damaged and tighten to the correct torque.
6.Loosen 15 sump bolts by approximately 3 turns,
allowing sump to drop away from rear oil seal
housing. Do not loosen 3 boltsAaround oil
pump housing.
7.Remove bolts securing oil seal housing, remove
seal and housing assembly.
Refit
1.Clean seal seating area of block and accessible
area of sump gasket. Sump gasket must be
replaced if damaged.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-061 over crankshaft boss and fit
oil seal and housing assembly.
4.Remove tool.
5.Fit and tighten seal housing bolts to correct
torque in sequence shown.
10Nm
6.Tighten sump bolts to correct torque and in the
correct sequence.
See Engine Sump Gasket
7.Fit flywheel.
8.Fit clutch assembly.
9.Fit gearbox.

Mpi
21
REPAIR
CAUTION: Never use the camshaft gears,
gear retaining bolts or timing belt to rotate
crankshaft.
7.Fit tool LRT-12-058 to lock flywheel.
8.Position tool LRT-12-060 to lock camshaft gears.
9.Loosen camshaft belt tensioner pulley bolt.
10.Move tensioner to release timing belt tension.
11.Retighten tensioner pulley bolt.
12.Remove 4 bolts securing crankshaft pulley to
crankshaft timing gear.13.Fit tool LRT-12-059 to crankshaft pulley, fit 2
pulley bolts to retain tool.
14.Restrain crankshaft pulley using tool LRT-12-059
and remove crankshaft pulley bolt.
15.Remove bolts securing tool LRT-12-059, remove
crankshaft pulley.
16.Remove timing belt lower cover.
17.If timing belt is to be refitted, mark direction of
rotation of belt.
18.Remove timing belt.

12ENGINE
22
REPAIR
CAUTION: Ease timing belt off gears using
fingers only. Metal levers may damage the
belt and gears. Do not rotate engine with
timing belt removed and cylinder head fitted.
Timing belts must be stored and handled with
care. Always store a timing belt on its edge with a
bend radius greater than 50 mm. Do not use a
timing belt which has been twisted or bent double
as this can fracture reinforcing fibres. Do not use
an oil contaminated timing belt. Although the belt
has a service life of 96,000 miles, 160,000 km, an
existing belt should only be refitted if it has
completed less than 48,000 miles, 80,000 km.
Refit
NOTE: For torque values.See
Specifications, torque, Torque values
1.Clean timing belt gears and pulleys.
2.Clean crankshaft pulley.
CAUTION: If original belt is to be refitted,
ensure direction of rotation mark is facing
correct way.
3.Fit timing belt to gears, starting at the crankshaft
gear and working in an anti-clockwise direction.
CAUTION: Ensure the belt run between the
crankshaft and exhaust camshaft gear is
kept taut during the fitting procedure.
4.Fit timing belt lower cover, tighten 3 bolts to the
correct torque.
5.Fit crankshaft pulley to crankshaft timing gear.
6.Fit tool LRT-12-059 to crankshaft pulley, fit 2
bolts to retain tool.
7.Fit crankshaft pulley centre bolt, and using tool
LRT-12-059 to restrain pulley, tighten bolt to the
correct torque.
8.Remove tool LRT-12-059
9.Fit bolts securing crankshaft pulley to timing
gear, tighten bolts to the correct torque.
10.Remove tool LRT-12-060.Tension belt
1.Loosen timing belt tensioner pulley bolt.
2.Apply
40Nmanti-clockwise torque to inlet cam
pulley bolt and release.
3.Tighten tensioner pulley bolt to the correct
torque.
4.Remove tool LRT-12-058 from flywheel.
5.Fit timing belt centre cover, tighten 5 bolts to the
correct torque.
6.Fit timing belt upper cover, tighten 5 bolts to the
correct torque.
7.Fit drive belt.