1995 LAND ROVER DISCOVERY oil

Mpi
5
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1.Remove gearbox.
2.Remove clutch assembly.
3.Remove flywheel.
4.Drain engine oil.
5.Fit sump plug, replacing sealing washer if
damaged and tighten to the correct torque.
6.Loosen 15 sump bolts by approximately 3 turns,
allowing sump to drop away from rear oil seal
housing. Do not loosen 3 boltsAaround oil
pump housing.
7.Remove bolts securing oil seal housing, remove
seal and housing assembly.
Refit
1.Clean seal seating area of block and accessible
area of sump gasket. Sump gasket must be
replaced if damaged.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-061 over crankshaft boss and fit
oil seal and housing assembly.
4.Remove tool.
5.Fit and tighten seal housing bolts to correct
torque in sequence shown.
10Nm
6.Tighten sump bolts to correct torque and in the
correct sequence.
See Engine Sump Gasket
7.Fit flywheel.
8.Fit clutch assembly.
9.Fit gearbox.

12ENGINE
6
REPAIR ENGINE
Service repair no - 12.41.01
Remove
1.Site vehicle onto ramp [hoist].
2.Remove the drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator - Mpi
4.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
5.Drain engine oil.
6.Position absorbent cloth around fuel pipe to fuel
rail union.
Unscrew union to relieve pressure.
CAUTION: Plug the connections
7.Release clip and disconnect hose from coolant
pump.
8.Release clip and disconnect hose from heater
rail.

Mpi
9
REPAIR 29.Disconnect oil pressure switch multiplug.
30.Disconnect air conditioning compressor
multiplug.
31.Remove 3 bolts securing engine harness to
manifold and fuel pipe.
32.Disconnect knock sensor multiplug.
33.Remove 2 nuts securing harness to starter motor
solenoid, remove harness.
34.Disconnect crankshaft sensor multiplug.
35.Disconnect fuel injection harness multiplug.
36.Disconnect inlet manifold air temperature sensor
multiplug.
37.Release clip and disconnect fuel hose from
pressure regulator.
CAUTION: Plug the connections.

12ENGINE
10
REPAIR
38.Disconnect 2 ignition coil multiplugs.
39.Disconnect 3 vacuum hoses from manifold.
40.Release cover and remove bolt securing earth
lead to cylinder block.
41.Move earth lead aside.
42.Remove 4 bolts securing air conditioning
compressor, move compressor aside.

12ENGINE
12
REPAIR 51.Remove engine L.H. and R.H. mounting lower
nuts.
52.Lower vehicle.
53.Raise engine.
54.Remove engine mountings.
55.Lower engine.
56.Remove bell housing top nut.
57.Raise engine and support gearbox.58.Remove 12 remaining bell housing nuts.
59.Remove engine.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
1.Using assistance, lower engine into position.
2.Fit bell housing nuts, tighten to the correct
torque.
3.Remove gearbox support.
4.Lower engine.
5.Fit bell housing top nut, tighten to the correct
torque.
6.Raise engine.
7.Position engine mountings, partially tighten nuts.
8.Lower engine.
9.Remove hoist and chains.
10.Tighten L.H. and R.H. mounting nuts to the
correct torque. Fit engine mounting heatshield.
11.Fit new gasket to exhaust downpipe.
12.Fit exhaust manifold to downpipe nuts and
tighten to the correct torque.
13.Tighten exhaust downpipe to silencer box nuts
to the correct torque.
14.Position air conditioning compressor and secure
with bolts. Tighten to the correct torque.
15.Connect coil multiplugs.
16.Connect harness to starter solenoid and secure
with nuts.
17.Connect earth lead to cylinder block and secure
with nut.
18.Position engine harness to manifold, secure with
bolts.

Mpi
13
REPAIR 19.Connect crankshaft sensor, knock sensor, air
conditioning compressor, fuel injector harness,
inlet manifold air temperature and fuel
temperature sensor multiplugs.
20.Connect fuel hose to pressure regulator and
secure with clip.
21.Fit and tighten fuel pipe to fuel rail union.
22.Connect multiplugs to throttle housing.
23.Connect vacuum hose to manifold.
24.Connect oil pressure switch multiplug.
25.Connect brake servo hose to manifold, secure
with clip.
26.Connect throttle cable to cam.
27.Position engine harness and connect breather
hose to inlet manifold, secure with clip.
28.Connect coolant temperature sensor multiplugs,
secure harness with cable tie.
29.Connect oxygen sensor multiplug, secure
harness with cable tie.
30.Connect alternator harness.
31.Connect heater hose to heater rail and secure
with clip.
32.Connect hose to coolant pump and secure with
clip.
33.Connect inlet hose to power steering pump and
secure with clip.
34.Fit and tighten outlet pipe union to power
steering pump.
35.Connect bypass and top hose, secure with clip.
36.Connect air cleaner to throttle housing hose and
secure with clip.
37.Remove engine lifting bracket.
38.Position spark plug cover and secure with
screws.
39.Fill engine with oil.
40.Fit bonnet [hood].
See CHASSIS AND BODY,
Repair, Bonnet [Hood]
41.Fit radiator.See COOLING SYSTEM, Repair,
Radiator - Mpi
42.Adjust throttle cable.See FUEL SYSTEM,
Adjustment, Throttle Cable Adjustment
ENGINE SUMP GASKET
Service repair no - 12.60.43
Remove
1.Drain engine oil.
2.Refit drain plug, use new sealing washer if
necessary, tighten to the correct torque.
3.Remove 18 bolts securing sump.
NOTE: 25mm long bolt is fitted at rear L.H.
corner of sump.
4.Release sump from cylinder block.
5.Discard gasket.

12ENGINE
14
REPAIR Refit
1.Clean sump, remove all traces of gasket from
mating faces of sump and cylinder block.
Visually check sump for damage.
2.Apply beads of RTV sealant to front main
bearing cap.
3.Position new gasket to sump, ensuring that
location pips on gasket are located in sump.
Check gasket lays flat on sump flange.
4.Fit sump. Fit bolts, ensuring that longest bolt is
inserted at position 7.
5.Working around the sump in the sequence
illustrated, tighten the bolts to the stage 1 torque
figure. Then, in the same sequence, tighten the
bolts to the stage 2 torque figure.
NOTE: For torque values.See
Specifications, torque, Torque Values
6.Fill engine with oil.CYLINDER HEAD GASKET
Service repair no - 12.29.01
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Unscrew union to relieve pressure.
CAUTION: Plug the connections.
WARNING: Do not carry out the next
instruction until the coolant is cool to
avoid personal injury from scalding.
3.Release clip and disconnect radiator bottom
hose, allowing coolant to drain into a suitable
container.

Mpi
17
REPAIR 22.Raise vehicle
23.Remove 4 nuts securing downpipe to exhaust
manifold.
24.Release downpipe from exhaust manifold.
25.Collect gasket.
26.Release 4 screws and remove spark plug cover.
27.Release spark plug leads from spark plugs and
release from clips. Place aside.
28.Remove camshaft covers.
29.Remove timing belt.
See Camshaft Front Oil
Seal
30.Progressively loosen and remove 10 cylinder
head bolts in sequence shown.
31.Remove cylinder head complete with manifold,
place on blocks to prevent damage.
32.Remove and discard cylinder head gasket.
33.Remove location dowels from cylinder block.
34.Inspect cylinder head for damage, cracks and
burning.
35.Inspect cylinder block. Ensure that the oil
restrictor is clear and fitted below the block face.
36.Clean all traces of gasket material from head
and block mating faces, using release agent and
plastic scraper.
37.Check cylinder head and block faces for
warpage:
Longitudinal warp = 0.1 mm max.
Transverse warp = 0.1 mm max.
Diagonal warp = 0.1 mm max.
38.Decarbonize cylinder head and pistons if
necessary.
39.Clean cylinder head bolt threads with a wire
brush, check for damage, replace if necessary.
40.Check cylinder block threads by running bolts
into threads using fingers only. Clean any tight
threads using M11 x 1.5 mm tap. Remove all
traces of oil from bolt holes.