1995 LAND ROVER DISCOVERY coolant

26COOLING SYSTEM
4
REPAIR THERMOSTATIC SENSOR
Service repair no - 19.22.18
Remove
1.Disconnect Lucar connector from sensor.
2.Remove sensor.
Refit
3.Clean sensor.
4.Apply Loctite 405 to threads of sensor.
5.Fit sensor and tighten to
15Nm
6.Connect Lucar to sensor.
7.Top-up cooling system.THERMOSTAT
Service repair no - 26.45.01
Remove
1.Position suitable container to collect coolant.
2.Slacken 2 clips and release radiator top hose.
3.Release bypass hose from securing bracket.
4.Release top hose from securing bracket.
5.Remove top hose.

MANIFOLD AND EXHAUST SYSTEM
5
REPAIR INLET MANIFOLD GASKET - Mpi
Service repair no - 30.15.08
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Unscrew union to relieve fuel
pressure. Re-tighten union.
CAUTION: Plug connections.
3.Release clip and remove air cleaner to throttle
housing hose.
4.Disconnect stepper motor multiplug.
5.Disconnect throttle potentiometer multiplug.
6.Release throttle cable from abutment bracket.
7.Release throttle cable from cam. Remove
coolant bypass hose.
8.Disconnect fuel temperature sensor multiplug.
9.Release clip and disconnect brake servo hose
from manifold.

MANIFOLD AND EXHAUST SYSTEM
7
REPAIR Refit
19.Ensure mating faces of inlet manifold and
cylinder head are clean.
20.Fit a new gasket, position inlet manifold to
cylinder head.
21.Fit nuts and bolts, tighten in the order shown to
the correct torque
25Nm
22.Position engine breather hose to manifold and
secure with bolts.
23.Connect fuel injector harness and intake air
temperature sensor multiplug.
24.Connect fuel hose to pressure regulator and
secure with clip.
25.Fit fuel pipe to fuel rail, tighten union to
10Nm
26.Connect vacuum hoses to manifold.
27.Position engine harness and cam cover brackets
to manifold, secure with bolts.
28.Connect breather hose and brake servo hose to
manifold, secure with clips.
29.Connect multiplug to fuel temperature sensor.
30.Connect breather hose to throttle housing and
secure with clip.
31.Connect throttle cable to cam and secure to
abutment bracket.
32.Connect coolant bypass hose to throttle housing.
33.Connect stepper motor and throttle
potentiometer multiplugs.
34.Connect air cleaner hose to throttle housing and
secure with clip.
35.Connect battery negative lead.
36.Adjust throttle cable.EXHAUST MANIFOLD GASKET - Mpi
Service repair no - 30.15.12
Remove
1.Raise vehicle.
2.Loosen 2 nuts securing downpipe to silencer
box.
3.Remove 4 nuts securing downpipe to exhaust
manifold.
4.Release downpipe from exhaust manifold.
5.Discard gasket.

30MANIFOLD AND EXHAUST SYSTEM
8
REPAIR 6.Disconnect oxygen sensor multiplug.
7.Release multiplug from bracket on thermostat
housing.
8.Release harness from cable tie.
9.Remove drive belt.
10.Remove 2 front bolts securing generator to
mounting bracket.
11.Remove 2 rear bolts securing generator to
mounting bracket.
12.Move generator from mounting bracket and
place aside.
13.Remove exhaust manifold heat shield.
14.Remove dipstick and bolt securing dipstick tube
to coolant rail.
15.Remove dipstick tube from cylinder block.16.Remove 3 bolts and 2 nuts securing exhaust
manifold to cylinder head.
17.Release coolant rail bracket from manifold studs.
18.Remove exhaust manifold and discard gasket.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
19.Clean mating faces of exhaust manifold and
cylinder head.
20.Fit new manifold gasket and align exhaust
manifold to cylinder head.
21.Position coolant rail bracket to manifold studs.
22.Fit manifold nuts and bolts, tighten to the correct
torque in the order shown.
23.Secure oxygen sensor multiplug to bracket.
24.Connect oxygen sensor multiplug.
25.Fit new manifold flange gasket and align exhaust
front pipe to manifold.
26.Fit nuts and tighten diagonally to the correct
torque.
27.Tighten exhaust downpipe to silencer box nuts
to the correct torque.
28.Position generator to mounting bracket.
29.Fit and tighten 4 generator securing bolts.
30.Refit drive belt.

MANIFOLD AND EXHAUST SYSTEM
9
REPAIR MANIFOLD CHAMBER GASKET - Mpi
Service repair no - 30.15.37
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Loosen union to relieve pressure.
Re-tighten union.
3.Release clip and remove air cleaner to throttle
housing hose.
4.Disconnect stepper motor and throttle
potentiometer multiplugs.
5.Release clip and disconnect breather hose from
throttle housing.
6.Release throttle cable from abutment bracket.
7.Release throttle cable from cam. Remove
coolant bypass hose from throttle housing.
8.Disconnect fuel temperature sensor multiplug.
9.Release clip and disconnect brake servo hose
from manifold.

30MANIFOLD AND EXHAUST SYSTEM
10
REPAIR 10.Release clip and disconnect breather hose from
manifold.
11.Release 2 bolts securing camshaft cover
brackets to manifold.
12.Disconnect 4 vacuum hoses from manifold.
13.Remove 6 bolts securing manifold chamber to
lower manifold.
14.Remove manifold chamber and collect gaskets.
Refit
NOTE: For torque values.See
Specifications, torque, Torque Values
15.Ensure mating faces of manifold chamber and
lower manifold are clean.
16.Fit a new gasket, position manifold chamber to
lower manifold.
17.Fit bolts, tighten to the correct torque.
18.Connect vacuum hoses to manifold.
19.Position camshaft cover brackets to manifold,
secure with bolts.
20.Connect breather hose and brake servo hose to
manifold, secure with clips.
21.Connect multiplug to fuel temperature sensor.
22.Connect breather hose to throttle housing and
secure with clip.
23.Connect throttle cable to cam and secure to
abutment bracket.
24.Connect coolant bypass hose to throttle housing.
25.Connect stepper motor and throttle
potentiometer multiplugs.
26.Connect air cleaner hose to throttle housing and
secure with clip.
27.Reconnect battery negative lead.
28.Adjust throttle cable.

ZF
5
REPAIR Remove
1.Select low range with transfer gear lever.
2.Remove knob and gaiter from transfer gear
lever.
3.Disconnect battery terminals.
4.Remove insulation pad from rocker cover and
inlet manifold.
5.On LH drive vehicles only, disconnect multi-plug
from top of brake fluid reservoir.
6.Release electrical harness from clips along top
of bulkhead and pull over to one side.7.Remove bolt securing transfer and main gearbox
breather pipe clip to rear of cylinder head.
8.Disconnect kick down cable at fuel injection
pump.
9.Drain coolant from cooling system.
10.Disconnect top hose from radiator.
11.Disconnect turbo charger hose from inter-cooler.
12.Remove starter heat shield.

ZF
7
REPAIR Accessories removal/fitting
If fitting a replacement transmission assembly to the
vehicle, remove the following items from the existing
assembly and fit to the replacement.
CAUTION: It is important to remove the
spacer from the extension shaft and fit
onto the replacement unit.
50.Breather pipe union and washers from main
gearbox.
51.Breather pipe, union and washers from transfer
gearbox.
52.Main gearbox selector lever.
53.RH mounting bracket assembly.
54.Oil cooler pipe unions.
55.Fit blanks to all apertures where unions have
been removed and blank off pipe ends.
Refit
1.Fit transmission to cradle and hoist.
2.Locate hoist under vehicle and remove torque
convertor retaining strap.
3.Ensure low range gear is engaged.
4.Apply approved sealant to bell housing face.
5.Carefully raise assembly, align bell housing with
flywheel housing and bring mating faces
together.
6.Fit nuts and bolts to secure transmission to
engine.
7.Locate electrical wiring and breather pipes to
position.
8.Secure kick down cable clip to bell housing.
9.Raise hoist sufficiently to take weight.
10.Remove block and jack from engine sump.
11.Fit filler/dipstick tube to gearbox sump and
secure bracket to bell housing.
12.Apply Loctite to torque convertor bolts
13.Working through starter aperture refit the four
torque convertor to flexible drive securing bolts,
rotating crankshaft to gain access to bolt
locations.
14.Refit starter and heatshield.
15.Secure breather pipes and harness with ties.
16.Fit left hand mounting bracket assembly to
gearbox.
17.Raise transmission and support with a suitable
ramp [hoist] jack.
18.Remove two bolts securing transmission to
cradle, lower hoist and remove from under
vehicle.
19.Apply Loctite to above bolts and fit to transfer
gearbox input bearing support plate.
20.Fit chassis cross member.21.Secure gearbox mounting brackets to chassis
cross member.
22.Remove ramp [hoist] jack.
23.Connect electrical leads to differential lock
switch.
24.Connect inhibitor switch multi-plug.
25.Connect selector cable to lever on side of
gearbox.
26.Connect oil cooler pipes to gearbox and secure
retaining bracket to gearbox sump.
27.Secure silencer to chassis and refit exhaust front
pipe.
28.Refit front propeller shaft to transfer gearbox.
29.Refit rear propeller shaft.
See PROPELLER
SHAFTS, Overhaul, Flexible Coupling
30.Connect speedometer cable to transfer gearbox.
31.Refill transfer gearbox with correct grade of
lubricating oil.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids
32.Lower ramp [hoist] to ground level.
33.Reconnect turbo-charger hose to inter-cooler.
34.Reconnect top hose to radiator.
35.Refill cooling system with correct mixture of
coolant.
See LUBRICANTS, FLUIDS AND
CAPACITIES, Information, Recommended
Lubricants and Fluids
36.Reconnect kick down cable to fuel injection
pump.
37.Secure breather pipe clip to rear of cylinder
head.
38.Engage harness with clips along top of
bulkhead.
39.On left hand drive vehicles only, connect
multi-plug to top of brake fluid reservoir.
40.Refit insulation pad to rocker cover and inlet
manifold, secure with oil filler cap.
41.Refit gaiter and knob to transfer gear lever.
42.Select high range gear.
43.Reconnect battery terminals.
44.Refill main gearbox with correct grade of
lubricating oil.
See LUBRICANTS, FLUIDS
AND CAPACITIES, Information,
Recommended Lubricants and Fluids