1995 LAND ROVER DISCOVERY radiator

26COOLING SYSTEM
4
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Drain cooling system.
See Adjustment,
Coolant
2.Remove viscous coupling and fan assembly.
See Viscous Coupling, Fan Blades, Pulley
and Fan Cowl
3.Release 2 clips and remove fan cowl.
4.Disconnect radiator top hoses.
5.Disconnect four transmission and engine oil
cooler connections to radiator end tanks. Note oil
spillage will occur when connections are
loosened. Blank off exposed oil connections.
6.Disconnect transmission oil temperature sensor.
7.Remove radiator securing brackets from each
side.
8.Remove radiator unit by lifting from its location.
Check condition of rubber mounting pads.Refit
9.Reverse removal procedure.
10.Clean unions and apply sealant.
11.Lubricate new 'O' rings before fitting.
12.Check radiator sealing strips are securely
located.
13.Transfer oil cooler adaptors if fitting new radiator.
14.Ensure that oil cooler connections are tightened
to
30 Nm.before fitting fan blades and cowl.
15.Clean coolant/oil spillage from vehicle.
16.Check all connections for coolant/oil leaks.

V8i
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Oil cooler pipes 30..........................................................................................
Radiator filler plug (plastic) 6.........................................................................

26COOLING SYSTEM
2
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Disconnect battery negative lead.
WARNING: Do not carry out the next
instruction until the coolant is cool to
avoid personal injury from scalding.
2.Slacken clip and release bottom hose from
radiator, allow coolant to drain into a suitable
container
3.Slacken clip and release bottom hose from
radiator rail.
4.Slacken clip and release top hose from radiator.
5.Release air cleaner to throttle housing hose from
securing brackets.
6.Slacken clip and release bypass hose from
radiator.
7.Slacken clip and release top expansion hose
from radiator.
8.Remove 2 bolts securing radiator side support
brackets.
9.Collect L.H. support bracket and position R.H.
support bracket aside.
10.Slacken clip and release heater hose from
radiator rail.
11.Disconnect 2 multiplugs from cooling fan
assemblies.

Mpi
3
REPAIR
12.With assistance lift out radiator assembly.
Do not carry out further dismantling if component
is removed for access only.
13.Remove 2 bolts securing radiator rail to radiator.
14.Remove radiator rail.
15.Remove 8 nuts securing fan assemblies to
radiator.
NOTE: Vehicles without air conditioning
have one cooling fan fitted.
Refit
16.Position fan assemblies to radiator and tighten
nuts to
6Nm
17.Position radiator rail to radiator and secure with
bolts.
18.Position radiator to vehicle.
19.Secure radiator to body with the side support
brackets and retaining bolts.
20.Connect multiplugs to cooling fans.
21.Fit and secure 6 hoses to radiator.
22.Secure air cleaner to throttle housing to
brackets.
23.Refill cooling system.
24.Reconnect battery negative lead.

26COOLING SYSTEM
4
REPAIR THERMOSTATIC SENSOR
Service repair no - 19.22.18
Remove
1.Disconnect Lucar connector from sensor.
2.Remove sensor.
Refit
3.Clean sensor.
4.Apply Loctite 405 to threads of sensor.
5.Fit sensor and tighten to
15Nm
6.Connect Lucar to sensor.
7.Top-up cooling system.THERMOSTAT
Service repair no - 26.45.01
Remove
1.Position suitable container to collect coolant.
2.Slacken 2 clips and release radiator top hose.
3.Release bypass hose from securing bracket.
4.Release top hose from securing bracket.
5.Remove top hose.

Mpi
5
REPAIR 6.Remove clip securing thermostat in hose.
7.Lubricate hose in front of thermostat and
manoeuvre thermostat from hose.
Refit
8.Lubricate inside of top hose with liquid soap.
9.Manoeuvre thermostat into hose to previous
position.
10.Fit and tighten clip securing thermostat to top
hose.
11.Refit radiator hose.
12.Top-up cooling system.

R380
1
REPAIR R380 MANUAL GEARBOX
Service repair no - 37.20.02
Remove
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
1.Install vehicle on a ramp [hoist].
2.Disconnect battery earth lead.
3.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
4.Remove sound insulation from top of
transmission tunnel.
5.Remove bolt and remove upper gear lever.
6.Remove screws securing gear selector lever and
high/low selector lever draft excluders.
7.Remove draft excluder clamp rings.
8.Remove handbrake cable clevis pin clip and
clevis pin.
9.Remove 'C' clip and cable adjuster.
10.Select low range to prevent gear lever fouling
tunnel when removing gearbox.
11.Remove bolt securing gearbox breather pipe clip
to cylinder block.
12.Remove bolts securing fan cowl to radiator.
13.Release fan cowl from radiator and lay over fan
blades.
14.Raise ramp [hoist].
15.Drain oil from main gearbox and transfer
gearbox.
See SECTION 10, Maintenance,
Under Vehicle Maintenance
16.Remove exhaust front pipe(s).See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
System Complete
17.Release intermediate exhaust pipe(s) from
mountings and tie aside.
18.Remove bolts securing clutch slave cylinder.
19.Release slave cylinder from clutch housing and
collect spacer.
20.Mark propeller shaft drive flange relationships for
reassembly.
21.Disconnect front and rear propeller shafts from
transfer gearbox. Tie shafts aside.
22.Remove clamp and disconnect speedometer
cable from transfer gearbox.
23.Release handbrake cable from transmission
tunnel.
24.Temporarily support transmission in a way which
enables the crossmember to be removed and a
hoist cradle to be fitted.

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.