1995 LAND ROVER DISCOVERY check oil

AIR CONDITIONING
9
REPAIR
10.Disconnect multiplug connecting heater to
blower unit, remove 3 screws and remove
blower unit.
11.Remove 5 screws securing casing to bulkhead
and tunnel.
12.Remove 2 securing bolts and remove centre
console front mounting bracket.
13.Disconnect 2 drain tubes..
14.Ease heater and cooler unit from its location and
remove from vehicle.
Refit
15.Ease heater and cooler unit into position.
16.Fit retaining bolts finger tight. Tighten in
sequence, centre and top bolts and then the
bottom bolt.
17.Reverse removal procedure.
18.Use new 'O' rings and lubricate with refrigerant
oil.
19.Evacuate and recharge system.
See
Adjustment, Refrigerant Recovery Recycling
Recharging
20.Leak test any disturbed joints.See Adjustment,
Leak Test System
21.Perform a functional check.EVAPORATOR AND EXPANSION VALVE
Service repair no - 86.25.20 - Evaporator
Service repair no - 86.25.01 - Expansion valve
Remove
WARNING: Wear eye and hand protection
when disconnecting components
containing refrigerant. Plug all exposed
connections immediately.
1.Remove heater and cooler unit.
See Heater
and Cooler Unit

82AIR CONDITIONING
10
REPAIR 2.Disconnect 2 Lucar connectors from thermostat.
3.Position wiring aside.
4.Remove 2 screws securing heater pipe bracket
and position pipes aside.
5.Remove 10 clips retaining upper and lower
casings.
6.Remove 5 screws retaining upper casing.
7.Remove lower casing and evaporator.
8.Remove 4 clips securing evaporator top cover.
9.Remove evaporator top cover.
10.Remove thermostat sensor from evaporator
matrix.
11.Remove evaporator assembly from lower casing.
12.Remove bulkhead seal from case.
Expansion valve
13.Remove insulation from evaporator and
expansion valve connections.
14.Remove expansion valve sensor retaining clip.
15.Unscrew 2 pipe unions. Discard 'O' ring seals.
CAUTION: Use a second wrench to
support pipe adapters and plug
connections.
16.Remove expansion valve.
17.Unscrew pipe union. Discard 'O' ring seal.
18.Remove evaporator pipe.
Refit
19.Reverse removal procedure. Use new 'O' rings,
insulation and bulkhead seal.
NOTE: Use refrigerant oil on all 'O' rings
and mating surfaces. Tighten connection
See Specifications, torque, Torque Values
20.Wrap all exposed metal at hose connections with
prestite tape.
21.Evacuate and recharge system.
See
Adjustment, Refrigerant Recovery Recycling
Recharging
22.Leak test any disturbed joints.See Adjustment,
Leak Test System
23.Perform a functional check.
24.Disconnect service unit.

AIR CONDITIONING
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Air conditioning
Compressor flange bolts 10............................................................................
Receiver drier union bolts 6...........................................................................
Dual pressure switch 11..................................................................................
Pressure pipe union nuts - M16 14.................................................................
Discharge pipe union nuts - M22 22...............................................................
Suction pipe union nuts - M24 33...................................................................
AIR CONDITIONING CHARGE DATA
Total oil in system 180ml - 6.3Fl oz...........................................................................
Total refrigerant in system 0,90kg - 32Fl oz..............................................................
Total refrigerant in system with rear air conditioning 1,15kg - 40Fl oz.......................

86ELECTRICAL
2
FAULT DIAGNOSIS LUCAS CONSTANT ENERGY IGNITION SYSTEM -
V8i
Preliminary checks
Inspect battery cables and connections to ensure they
are clean and tight. Check electrical condition of
battery.
Inspect all L.T. connections, ensure they are clean
and tight. Check H.T. leads are correctly positioned
and not shorting to ground against any engine
components. Wiring harness and individual cables
should be firmly fastened to prevent chaffing.
Pick-up air gap
Check air gap between pick-up limb and reluctor teeth
is 0.20 - 0.35 mm, using a non-ferrous gauge.
NOTE: Air gap is set initially at factory and
will only require adjusting if tampered with
or when pick-up module is replaced.
TEST 1:
H.T. Sparking
Remove coil/distributor H.T. lead from distributor
cover and hold approximately 6mm from engine block,
using suitable insulated pliers. Switch ignition 'On' and
operate starter.
Regular sparking indicates fault in H.T. distribution,
plugs, timing or fuelling, proceed to Test 6. If no spark
or weak spark occurs proceed to Test 2.TEST 2:
L.T. Voltage
Switch ignition 'On' - engine stationary.
(a) Connect voltmeter to points in circuit indicated
by V1 to V4 and make a note of voltage
readings.
(b) Compare voltages obtained with specified
values listed below:
Expected readings
V1 More than 12 volts.
V2 1 volt maximum below volts at V1.
V3 1 volt maximum below volts at V1.
V4 0 volt - 0.1 volt.
(c) If all readings are correct proceed to Test 3.
(d) Check incorrect reading(s) with chart to identify
area of possible faults, i.e. faults listed under
heading SUSPECT and rectify.
(e) If coil and amplifier is suspected, disconnect L.T.
lead at coil, repeat V3. If voltage is still incorrect,
fit new coil. If voltage is now correct, check L.T.
lead, if satisfactory fit new amplifier.
(f) If engine will not start proceed to Test 3.

86ELECTRICAL
4
FAULT DIAGNOSIS TEST 4:
Pick-up Coil Resistance
Remove amplifier.
Connect ohmmeter leads to two pick-up terminals in
body of distributor.
The ohmmeter should register between 2k and 5k
ohm if pick-up is satisfactory. If ohmmeter reading is
correct, check all connections between pick-up and
amplifier, if satisfactory, fit new amplifier. If engine still
does not start carry out Test 5.
Change pick-up if ohmmeter reading is incorrect. If
engine still does not start proceed to Test 5.TEST 5:
Coil H.T. Sparking
Remove existing coil/distributor H.T. lead and fit test
H.T. lead to coil tower. Using suitable insulated pliers,
hold free end about 6mm from engine block and crank
engine. There should be good H.T. sparking.
If weak or no sparking, fit new coil, repeat test.
H.T. sparking good, repeat test with original H.T. lead.
If sparking is good carry out Test 6.
If weak or no sparking, fit new H.T. lead, if engine will
not start carry out Test 6.

ELECTRICAL
5
FAULT DIAGNOSIS TEST 6:
Rotor Arm
Remove distributor cover. Disconnect coil H.T. lead
from cover, using insulated pliers hold about 3mm
above rotor arm electrode and crank the engine.
There should be no H.T. sparking between rotor and
H.T. lead. If satisfactory carry out Test 7.
If H.T. sparking occurs, an earth fault on rotor arm is
indicated. Fit new rotor arm. If engine will not start
carry out Test 7.
TEST 7:
Visual and H.T. Cable Checks
Examine: Should be:
1. Distributor Cover Clean, dry, no tracking marks.....................................................
2. Coil Top Clean, dry, no tracking marks....................................................................
3. H.T. Cable Insulation Must not be cracked, chafed or perished...............................................
4. H.T. Cable Continuity Must not be open circuit..............................................
5. Sparking Plugs Clean, dry, and set to correct gap........................................................
NOTE:
1. Reluctor Must not foul pick-up or leads...................................................................
2. Rotor and Insulation Cover Must not be cracked or show signs of tracking marks.....................................

86ELECTRICAL
6
REPAIR Refit
NOTE: If a new distributor is being fitted,
mark body in same relative position as
distributor removed.
8.Leads for distributor cap should be connected as
illustrated.
Figures 1 to 8 inclusive indicate plug lead
numbers.
RH-Right hand side of engine, when viewed
from rear.
LH-Left hand side of engine, when viewed from
rear.
9.If engine has not been turned while distributor
has been removed, carry out instructions 10. to
17. Alternatively proceed to instruction 18.
10.Fit new 'O' ring seal to distributor housing.
11.Turn distributor drive until centre line of rotor arm
is 30Ê anti-clockwise from mark made on top
edge of distributor body.
12.Fit distributor in accordance with alignment
markings.
NOTE: It may be necessary to align oil
pump drive shaft to enable distributor
drive shaft to engage in slot.
13.Fit clamp and bolt. Secure distributor in exact
original position.
14.Connect vacuum hose to distributor and low
tension lead to coil.
15.Fit distributor cap.
16.Reconnect battery.
17.Using suitable electronic equipment, set ignition
timing.
See Adjustment, Ignition timing
18.If engine has been turned with distributor
removed, carry out instructions 19 to 30.
19.Set engine-No. 1 piston to static ignition timing
figure
See ENGINE TUNING DATA,
Information, Engine 3.9 V8i
20.Turn distributor drive until rotor arm is
approximately 30Ê anti-clockwise from number
one sparking plug lead position on cap.
21.Fit distributor to engine.
22.Check that centre line of rotor arm is now in line
with number one sparking plug lead on cap.
Reposition distributor if necessary.
23.If distributor does not seat correctly in front
cover, oil pump drive is not engaged. Engage by
lightly pressing down distributor while turning
engine.
24.Fit clamp and bolt, do not tighten.
25.Set ignition timing statically to 6Ê B.T.D.C.
26.Connect vacuum hose to distributor.
27.Fit low tension lead to coil.
28.Fit distributor cap.
29.Reconnect battery.
30.Using suitable electronic equipment set the
ignition timing.
See Adjustment, Ignition
timing

86ELECTRICAL
34
REPAIR PRINTED CIRCUIT AND WARNING LIGHTS
1. Panel illumination bulbs
2. Transmission oil temperature warning lamp bulb
3. Hazard warning lamp bulb
4. Check engine warning lamp bulb
5. Handbrake/brake fluid warning lamp bulb
6. ABS warning lamp bulb
7. Headlamp main beam warning lamp bulb
8. Trailer direction warning lamp bulb9. Direction indicator warning lamp bulb
10. Air suspension warning lamp bulb
11. Ignition/no charge warning lamp bulb
12. Seat belt warning lamp bulb
13. Not used
14. Traction control warning lamp bulb
15. Diesel heater plug warning lamp bulb (if fitted)
16. Main printed circuit