1995 AUDI A4 AHA ATQ Engines Lubrication System Components Workshop Manual

17-21


- Unbolt bracket for oil supply lines (arrows) and pull front oil supply line
(longer line) down and remove.

-
Using Torx T45, unbolt chain sprocket from oil pump and pull off oil
pump.
Pa
ge 25 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

17-22


Installing
Installation is the reverse of removal, noting the following:
Note:
Do not use glue or sealant. - Remove oil pump together with shorter oil supply line.
- Before installing oil pump, install short oil supply line together with O-
rings into pump and into oil pan (upper part).
- Clean both sealing surfaces on oil pan (lower part) so they are free of
oil and grease.
- Install new gasket on oil pan (lower part) and attach to oil pan (upper
part) with two bolts diagonal to each other.
- Tighten all bolts hand tight.
- Starting in the center and moving toward the outside, tighten bolts to 10
Nm (7 ft lb).
- Install new seal on oil drain plug and tighten to 30 Nm (22 ft lb).
Pa
ge 26 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

17-23

Tightening torques

Component

Tightening
torque
Oil pan to cylinder block M6 10 Nm (7 ft lb)
M8 20 Nm (15 ft
lb)
Oil pan (lower part) to oil
pan (upper part) M6 10 Nm (7 ft lb)
Oil pan to transmission M8 25 Nm (18 ft
lb)
M10 45 Nm (33 ft
lb)
Coolant line to oil pan 10 Nm (7 ft lb)
Oil drain plug in oil pan
(lower part) 30 Nm (22 ft
lb)

Component

Tightening
torque
Dipstick tube to cylinder
head M6
M8 10 Nm (7 ft lb)
25 Nm (18 ft
lb)
Oil pump to engine block 25 Nm (18 ft
lb)
Oil supply line for oil pump 10 Nm (7 ft lb)
Pa
ge 27 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

to oil pan (upper part)
Oil seal carrier, front M6 10 Nm (7 ft lb)
Pa
ge 28 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

17-24


Component

Tightening torque
Collar screw M8 30 Nm (22 ft lb)
Stabilizer bracket to subframe 1) 25 Nm (18 ft lb)
Coolant drain plug to engine 20 Nm (15 ft lb)
Torque support stop to bracket on engine
25 Nm (18 ft lb)
Engine mount to subframe 25 Nm (18 ft lb)
Torque support to front side of oil pan 25 Nm (18 ft lb)
Engine mount to engine support 25 Nm (18 ft lb)
Chain sprocket to oil pump 25 Nm (18 ft lb)
1) Replace all self-locking nuts after removal.
Pa
ge 29 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

17-25


Other tightening torques Component

Tightening torque
Nut for engine mount -1- 25 Nm (18 ft lb)
Bolts -2- and -3- 60 Nm (44 ft lb)
Combination bolt -4- 2)
110 Nm (81 ft lb) + 90 2) Replace combination bolt -4- after removing.
Pa
ge 30 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

17-26

Front oil seal carrier and oil pump chain,
removing and installing


Removing

- Remove ribbed belt page 13
-8 .

- Remove toothed belt page 13
-12
.

- Remove oil pan (upper part) and oil pan (lower
part) page 17
-10
.

- Before removing front oil seal carrier, remove following components:
1 - Toothed belt tensioner roller
Tightening torque: 20 Nm (15 ft lb)
2 - Idler roller
Tightening torque: 45 Nm (33 ft lb)
3 - Toothed belt tensioner
Tightening torque: 20 Nm (15 ft lb)
4 - Toothed belt tensioner lever
Tightening torque: 20 Nm (15 ft lb)
5 - Crankshaft center bolt and toothed belt sprocket
Pa
ge 31 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1

17-27


Replacing oil pump drive chain - Remove front oil seal carrier and remove gasket from front oil seal
carrier (M6 bolts: 10 Nm, 7 ft lb) (Collar screw M8: 30 Nm 22 ft lb).

-
Using Torx T45, unbolt chain sprocket from oil pump and pull off oil
pump.
Pa
ge 32 of 34 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03.17.1