1994 PONTIAC FIREBIRD oil

When to Change Engine Oil:
See if any one of these is true for you:
Most trips are less than 4 miles
0 It’s below freezing outside and most
trips are less than
10 miles ( 16 km).
The engine is at low speed most of
the time (as in door-to-door delivery,
or
in stop-and-go traffic).
(6 km).
You tow a trailer often.
Most trips are through dusty places.
If any one of these is true for your
vehicle, then you need to change your
and filter every
3,000 miles (5 000 km) or
3 months - whichever comes first.
If none of them is true, change the oil
every
7,500 miles (12 500 km) or 12
months
- whichever comes first.
Change the filter at the first oil change
and at every other oil change after that.
Engine Coolant Heater (Engine Block
Heater):
An engine coolant heater can be a big
help if you have to park outside in very
cold weather,
0°F (-18°C) or colder. If
your vehicle has this option, see “Engine Coolant Heater” in the Index.
What to Do with Used Oil:
Did you know that used engine oil
:ontains elements that may be unhealthy
:or your skin and could even cause
:ancer? Don’t let used oil stay on your
;kin for very long. Clean your skin and
lails with soap and water, or a good hand
:leaner. Wash or properly throw away
:lothing or rags containing used engine
il. (See the manufacturer’s warnings
ibout the use and disposal of oil
xoducts.)
Used oil can be a real threat to the
mvironment. If you change your own oil,
)e sure to drain all free-flowing oil from
:he filter before disposal. Don’t ever
jispose of oil by putting it in the trash,
2ouring it on the ground, into sewers, or
into streams or bodies
of water. Instead,
recycle it by taking it to a place that
collects used oil. If you have a problem
properly disposing of your used oil, ask
your dealer, a service station or a local
recycling center for help.
3.4L L32 (Code S
Air Cleaner
iefer to the Maintenance Schedule to
letermine when to replace the air filter.
See “Scheduled Maintenance Services”
In the Index.
t
195 ...
ProCarManuals.com

Service and Appearance Care
Automatic Transmission Fluid
When to Check and Change:
A good time to check your automatic
transmission fluid level
is when the
engine oil is changed. Refer to the
Maintenance Schedule to determine when
to change your fluid. See “Scheduled
Maintenance Services” in the Index.
How to Check:
Because this operation can be a little
difficult, you may choose to have this
done at a Pontiac dealership Service
Department.
If you do it yourself, be sure to follow all
the instructions here, or
you could get a
false reading on the dipstick.
Too much or too little fluid can
damage your transmission. Too much
can mean that some of the fluid could
come out and fall on hot engine parts
or exhaust system, starting a fire. Be
sure to get an accurate reading
if you
check your transmission fluid. Wait
at least 30 minutes before checking
the transmission fluid level if you have
been driving:
When outside temperatures are above
At high speed for quite a while.
In heavy traffic - especially in hot
90°F (32°C).
weather.
While pulling a trailer.
To get the right reading, the fluid should
be at normal operating temperature,
which is 180°F to 200°F (82°C to 93°C).
To check transmission fluid hot: Get
the vehicle warmed up by driving
about
15 miles (24 km) when outside
temperatures
are above 50°F ( 10°C).
If it’s colder than 50°F ( lO”C), drive
the vehicle in
“D’ (Third Gear) until the
engine temperature gage moves and then
remains steady for
ten minutes. Then
follow the hot check procedures.
To check transmission fluid cold: A cold
check is made after the vehicle has been
sitting for eight hours or more with the
engine
off and is used only as a reference.
Let the engine run at idle for five minutes
if outside temperatures are 50°F
(10°C)
or more. If it’s colder than 50°F (lO°C),
you may have to idle the engine longer.
Should the fluid level be low during a
cold check, you must perform a hot check
before adding fluid. This will give you a
more accurate reading of the fluid level.
To check the fluid hot or cold:
0
Park your vehicle on a level place.
With the parking brake applied, place
the shift lever
in “P” (Park).
With your foot on the brake pedal,
move the shift lever through each gear
range, pausing for about three seconds
in each range. Then, position the shift
lever in “P” (Park).
Let the engine
run at idle for three
minutes or more.
. . .I98
ProCarManuals.com

Service and Appearanc’e Care
The proper coolant for your Pontiac will:
0
Give freezing protection down to
-34°F (-37°C).
Give boiling protection up to 262°F
(128°C)
.
Protect against rust and corrosion.
Help keep the proper engine
temperature.
Let the warning lights work as
they
should.
What to Use:
Use a mixture of one-half clean water
(preferably distilled) and one-half
antifreeze that meets
“GM Specification
1825M,” which won’t damage aluminum
parts. You can also use a recycled coolant
conforming to GM Specification 1825M
with a complete coolant flush and refill. If
you use this mixture, you don’t need to
add anything else.
NOTICE:
If you use an improper coolant mix,
your engine could overheat and be
badly damaged. The repair cost wouldn’t be covered by your war-
ranty. Too much water in the mix can
freeze and crack the engine, radiator,
heater core and other parts.
Adding Coolant
To Check Coolant: When your engine is
cold, check the dipstick on the cap of the
coolant recovery tank. The coolant level should be “COLD,” or a little higher.
When your engine is warm, the level on
the dipstick should be up to
“HOT,” or a
little higher.
. . .202
ProCarManuals.com

What to Add:
When you do need brake fluid, use only
DOT-3 brake fluid - such as Delco-
Supreme ll@
(GM Part No. 1052535).
Use new brake fluid from a sealed
container only, and always clean the
brake fluid reservoir cap before
removing it.
NOTICE:
Don’t let someone put in the
wrong kind of fluid. For example,
just
a few drops of mineral-based
oil, such as engine oil, in your
brake system can damage brake
system parts
so badly that they’ll
have to be replaced.
Brake fluid can damage paint,
so
be careful not to spill brake fluid on your vehicle. If you
do, wash it
off immediately. See “Appearance
Care”
in the Index.
Brake Wear
Unless you have the four-wheel disc
brake option, your Pontiac has front disc
brakes and rear drum brakes. Disc
brake pads have built-in wear
indicators that make a high-pitched
warning sound when the brake pads
are worn and new pads are needed. The
sound may come and
go or be heard all
the time your vehicle is moving (except
when you are pushing on the brake pedal
firmly).
I NOTICE:
I
Continuing to drive with worn-out
brake pads could result in costly
brake repair. Some driving conditions
or climates may
cause a brake squeal when the brakes are
first applied or lightly applied. This does
not mean something is wrong with your
brakes.
If you have rear drum brakes, they don’t
have wear indicators, but if you ever hear
a rear brake rubbing noise, have the rear
brake linings inspected. Also, the rear
brake drums should be removed and
inspected each time the tires are removed
for rotation or changing. When you have
the front brakes replaced, have
the rear
brakes inspected, too.
Brake linings should always be replaced
as complete axle sets.
Brake Pedal Travel
See your dealer if the brake pedal does
not return to normal height, or if there is a
rapid increase in pedal travel.
This could
be a sign
of brake trouble.
I.
207. . .
ProCarManuals.com

Service and Appearance Care
Don’t use any of these unless this manual
says you can. In many uses, these will
damage your vehicle:
0 Alcohol
Laundry Soap
0 Bleach
0 Reducing Agents
Cleaning the Inside of Your
Pontiac
Use a vacuum cleaner often to get rid of
dust and loose dirt. Wipe vinyl or leather
with a clean, damp cloth.
Your Pontiac dealer has two
GM cleaners,
a solvent-type spot lifter and a foam-type
powdered cleaner. They will clean normal
spots and stains very well. Do not use
them on vinyl or leather.
Here are some cleaning tips:
Always read the instructions on the
Clean up stains as soon as you can -
Use a clean cloth or sponge, and
cleaner
label.
before they set.
change to a clean area often. A soft
brush may be used
if stains are
stubborn.
D Use solvent-type cleaners in a
well-ventilated area only. If you use
them, don’t saturate
the stained area.
clean the entire area immediately or it
will set.
If a ring forms after spot cleaning,
Using Foam-Type Cleaner on Fabric
Vacuum and brush the area to remove
any loose dirt.
Always clean a whole trim panel or
section. Mask surrounding trim along stitch or welt lines.
Mix Multi-Purpose Powdered Cleaner
following the directions on the
container label.
Use suds only and apply with a clean
sponge.
Don’t saturate the material.
Don’t rub it roughly.
As soon as you’ve cleaned the section,
use a sponge to remove the suds.
Rinse the section with a clean, wet
sponge.
Wipe off what’s left with a slightly
damp paper towel or cloth.
Then dry it immediately with a blow
dryer or a heat lamp.
NOTICE:
Be careful with a hair dryer or heat
lamp.
You could scorch the fabric.
0 Wipe with a clean cloth.
Using Solvent-Type Cleaner on Fabric
First, see if you have to use solvent-type
cleaner at all. Some spots and stains will
clean
off better with just water and mild
soap.
If you need to use a solvent:
Gently scrape excess soil from the
trim material with a clean, dull knife
or scraper. Use very little cleaner, light
pressure and clean cloths (preferably cheesecloth). Cleaning should start at
the outside of the stain, “feathering”
toward the center. Keep changing to
a
clean section of the cloth.
. . .222
ProCarManuals.com

When you clean a stain from fabric,
immediately dry the area with an air
hose, hair dryer, or heat lamp to help
prevent a cleaning ring. (See
the
previous NOTICE.)
Special Cleaning Problems
Greasy or oily stains:
Such as grease,
oil, butter, margarine, shoe polish, coffee
with cream, chewing gum, cosmetic
creams, vegetable oils, wax crayon, tar
and asphalt.
0 Carefully scrape off excess stain.
0 Follow the solvent-type instructions
Shoe polish, wax crayon, tar and described earlier.
asphalt will stain if left on a vehicle
seat fabric. They should be removed
as soon as possible. Be careful,
because the cleaner will dissolve them
and may cause
them to spread
Non-greasy stains: Such as catsup,
coffee (black), egg, fruit, fruit juice, milk,
soft drinks, wine, vomit, urine and blood.
Carefully scrape off excess stain, then
sponge
the soiled area with cool water.
If a stain remains, follow the foam-type
instructions described earlier. If an
odor lingers after cleaning
vomit or urine, treat the area with
a waterhaking soda solution:
1 teaspoon (5 ml) of baking soda to
1 cup
(250 ml) of lukewarm water.
If needed, clean lightly with
solvent-type cleaner.
Combination stains: Such as candy,
ice cream, mayonnaise, chili sauce and
lnknown stains.
Carefully scrape off excess stain, then
clean with cool water and allow to
dry-
@ If a stain remains, clean it with
solvent-type cleaner.
Cleaning Vinyl
Use warm water and a clean cloth.
Rub with a clean, damp cloth to
remove dirt. You may have to do it
more than once.
Things like tar, asphalt and shoe
polish will stain if you don’t get them
off quickly. Use a clean cloth and a
solvent-type vinyl cleaner.
Cleaning Leather
Use a soft cloth with lukewarn water and
a mild soap or saddle soap.
For stubborn stains, use a mild
solution of
10% isopropyl alcohol
(rubbing alcohol) and
90% water.
solvent-based or abrasive cleaners,
furntiure polish or shoe polish on
leather.
immediately. If dirt is allowed,to work
into finish, it can harm the leather.
Cleaning the Top of the Instrument
Panel
Use only mild soap and water to Clean
the top surfaces of the instrument.pane1.
Sprays containing silicones or waxes
may cause annoying reflections in the
windshield and even make it difficult to
see through the windshield under certain
conditions.
Never use oils, varnishes,
Soiled leather should be cleaned
223. . .
ProCarManuals.com

Service and Appearance Care
Sheet Metal Damage
If your vehicle is damaged and requires
sheet metal repair or replacement, make
sure the body repair shop applies
anti-corrosion material to the parts
repaired or replaced to restore corrosion
protection.
Foreign Material
Calc'ium chloride and other salts, ice
melting agents, road oil and tar, tree sap,
bird droppings, chemicals from industrial chimneys, and other foreign matter can
damage your vehicle's finish
if they
remain on painted surfaces. Use cleaners
that are marked safe for painted surfaces
to remove foreign matter.
Finish Damage
Any stone chips, fractures or deep
scratches in the finish should be repaired
right away. Bare metal will corrode
quickly and may develop into a major
repair expense.
Minor chips and scratches can be repaired
with touch-up materials available from
your dealer or other service outlets.
Larger areas of finish damage can be corrected
in your dealer's body and paint
shop.
Underbody Maintenance
Chemicals used for ice and snow removal
and dust control can collect on the
underbody. If these are not removed,
accelerated corrosion (rust) can occur on
the underbody parts such as fuel lines,
frame, floor pan, and exhaust system even
though they have corrosion protection.
At least every spring, flush these
materials from the underbody with plain
water. Clean any areas where mud and
other debris cah collect. Dirt packed in
closed areas
of the frame should be
loosened before being flushed. Your
dealer or an underbody vehicle washing
system can do this for you.
Chemical Paint Spotting
Some weather and atmospheric conditions
:an create a chemical fallout. Airborne
?ollutants can fall upon and attack painted
curfaces on your vehicle. This damage
:an take two forms: blotchy,
inglet-shaped discolorations, and small
irregular dark spots etched into the paint
surface.
Although no defect in the paint job causes
this, Pontiac will repair, at no charge to
the owner, the surfaces of new vehicles
jamaged by this fallout condition within
12 months or 12,000 miles (20
000 km)
of purchase, whichever comes first.
. . ,226
ProCarManuals.com

Appearance Care and Maintenance Materials
PART NUMBER USAGE DESCRIPTION
SIZE
1051516
16
02. (0.473 L) 10501 73
Also old waxes, polishes
Tar
and Road Oil Remover
16 02. (0.473 L)
10501 72 Windshield washing system and gas line
Washer
Solvent and Gas Liner De-lcer
32
02. (0.946 L)
Windshield cleaner
Bon-Ami Powder"
12
02. (0.340 kg)
105001
1 Exterior cleaner and polish
Magic Mirror Cleaner-Polish
16
02. (0.473 L)
1050201 Spot and stain removal
on cloth and fabric Spot Lifter*
8 02. (0.237 L) 1051 398 Exterior wash
Wash-Wax (Concentrated)
16
02. (0.473
L)
1052870 Vinyl, cloth, door trims, seats, carpet, tires, mats Multi-Purpo\
se Powdered Cleaner
6
Ib. (2.72 kg)
1050429 Glass cleaning and
spot cleaning on vinyls Glass
Cleaner
24 02. (0.680 L)
1050427 Spot and stain removal
on cloth and fabric Fabric
Cleaner*
16 02. (0.473 L)
1050244 Spot and stain removal
on leather
and vinyl
VinyVLeather Cleaner*
32 02. (0.946 L)
105021 4 Cleans white and black tires White Sidewall Tire Cleaner 16
02. (0.473
L)
10501 74 Removes
rust and corrosion on chrome and steel
Cleaner and Polish
*Not recommended for pigskin suede leather.
See your General Motors Dealer for these products. See the Index under "Recommended Fluids and Lubricants" for other produc\
ts.
ProCarManuals.com