1994 MITSUBISHI 3000GT fuse

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio and Tape Player54-173C. CASSETTE PLAYER
C-lCassette tape will not be inserted.Are there any foreign objects in the cassette player?/NoRemove the object(s)”
“1Attempting to force a foreign object (e g.. a coin or clip, etc.) out
of the cassette player may damage the mechanism. The player
should be taken to a service dealer for repair.
Does the cassette player work if another tape is inserted?
NoReplace tape
**
*2Ensure that the tape label is not that the tape itself tape of C-120
or greater length often get caught in the mechanism and should
not be used.
Repair or replace cassette player.
C-2No sound (even after a tape has been inserted).Is multi-purpose fuse No. 4 blown or is the circuit open?
NoYes
- Replace fuse or repair harness.
+Is connector at rear of radio connected tightly?
YesNo
- Connect connector firmly.
Disconnect connector at rear of radio. Is ACC power being supplied to the
yesPW Repair or replace caSSette player.
radio?
1 TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Radio- and TaDe Plaver54-183
Card
Security code216N1034
Typical name card
A Cards
PROCEDURE FOR INPUTOFSECURITYCODE FOR RADIOAND TAPE PLAYER WITH ANTI-THEFT SYSTEM
The radio and tape player does not operate in the following
states.
(1) Power supply to the radio and tape player has been sus-
pended for more than one hour continuously by removing
the cable from the battery terminal or disconnecting the
harness connectors.
(2) The power supply to the radio and tape player has been
suspended for more than one hour owing to blown fuse
or discharged battery.(3) The radio and tape player has been replaced.
If the radio and tape player does not operate for these causes,
input the security code by the following procedure to operate
it.
1.Using any of the following methods, confirm the security
code.
(1)
Read the security code indicated on the cards retained
by the user.
(2) If the security code is unknown owing to the user’s
loss of the cards,a. Remove the audio panel and then pull out the
radio and tape player partially.
b.Read the serial No. shown on the name card of
the radio and tape player.
c.Look up the anti-theft code corresponding to the
serial number in the serial number-anti-theft code
table; or, make inquiries to Mitsubishi Motor Sales
of America, Inc.(3) When the radio and tape player is replaced
Read the security code on the cards attached to the
upper surface of the replacement radio and tape player.
NOTE
Deliver the cards (two) to the user.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Theft-alarm System54-213 1
FUSIB ELINK sb
~,J/B ‘;/I (c-68),DEDICATED
FUSE
R-B
0
1R-B5
6,,10A
RB[ 11;;
I‘
(c-78)
L-G
R-E
[
G-E
ON
14(c-76)
R-EG-R
(c-02)
7___-________---_8
G-Bi
58
D,'p,"," R-B
(A-26)
iEEi-HORN
(A-27)
G-B
L-G
ETACS UNIT(c-66)
LIFTGATE
CYLINDER
LOCK
SWITCH
(F-23)
,70
1B
1i;yTEfiTE
(c-57)
2G-R
(A-47)
1iv
GR
HORN(LH) (RH)
1
>
CLOCK
SPRING
C-lIA
9
GR
(F-24)2B
1
HORN
SWITCH
2Bdr
(A-06X)0
ii3
1423 q
5
cc-ss)
al/a1
@F-m (A-47) Gz3 (A-49) GF53 (c-02)(c-57)
m Lizi lla q la /fim$mqmj
oF7-ia(c-76)(m(c-80)

/
LJ
HRlBMOlBB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Theft-alarm System54-217
5W-B
DEDICATED
FUSE
i
ON
2
ETACS UNITDIODE58c-12R-B0
R-B,,lR-B,5
G-B
I
--____--__-----_
--I
(c-02)
87G-B
G-B
(c-57)
2
rl7
G-h
GR(A-47)
)
CLOCK
SPRINGrI!A
GR
I10
HORN
SWITCH
G-E
G-R
2EB
NOTE::1995 MODELSI
-
-----Am
(A-06x) (A-26) (A-27) (A-47) @Fm lA-49) (A-50) (c-02)(c-57)-
HR15M02BB
TSB Revision

Downloaded from www.Manualslib.com manuals search engine 54-222CHASSIS ELECTRICAL - Theft-alarm System
TROUBLESHOOTING QUICK-REFERENCE TABLE
For information concerning the locations of electrical components, refer to GENERAL-Theft-alarm System
Circuit.
1.ARMING / DISARMING RELATIONSHIP
Trouble symptomThe system is not armed (The
SECURITY light doesn’t illumi-
nate, and the alarm doesn’t func-
tion.)
(The central door locking system
functions normally.
If the central locking system doesnot function normally, refer to
GROUP 42.)
The arming procedures are fol-
lowed, but the SECURITY light
does not illuminate.(There is an alarm, however,
when an alarm test is conductedafter about 20 seconds have
passed.)
The alarm sounds in error when,
while the system is armed, a door
or the liftgate is unlocked by us-
ing the key.
ICause
Damaged or disconnected
wiring of ECU power sup-
ply circuit
Damaged or disconnected
wiring of door switch input
circuit
Damaged or disconnectedwiring of SECURITY light
activation circuit.Blown SECURITY light
bulb
Malfunction of the ECU.
Damaged or disconnected
wiring of a door key cylin-
der and the
liftgate unlock
switch input circuit.
Malfunction of a door key
cylinder and the liftgate un-
lock switch.
Malfunction of the ECU.
2.ACTIVATION / DEACTIVATION RELATIONSHIP
Trouble symptomCauseThere is no alarm when, as an
Damaged or disconnected
alarm test, a door is opened with-wiring of door switch (all
out using the key.doors) input circuit
(The arming and disarming arenormal, and the alarm is
acti-Malfunction of the door
vated when the liftgate or hood isswitch
opened.)
Malfunction of the ECUThere is no alarm when, as an
Damaged or disconnected
alarm test, the liftgate is opened
without using the key.wiring of liftgate switch in-
put circuit
(The alarm is activated, however,
by opening a door or the hood.)Malfunction of the liftgate
switch.
Malfunction of the ECU.Check methodCheck by using check
chart P.54-224.Check by using check
chart P.54-225.Check by using check
chart P.54-229.
If input checks
(P.54-220) indicate amalfunction, check by
using check chart
P&f-227.
Check method
If input checks
(P.54-220) indicate a
malfunction, check by
using check chart
P.54-225.
If input checks
(P.54-220) indicate a
malfunction, check by
using check chart
P.54-228.
Remedy
Replace the fusible link
No. (6) or the fuse No.
(19).Repair the harness.
Repair the harness or re-
place the door switch.
Replace the fusible linkNo. (6) or the fuse No.(1%
Repair the harness.
Replace the bulb.
Replace the ECU.
Repair the harness or re-
place a door key cylinderand the
liftgate unlock
switch.
Replace the ECU.
Remedy
Repairthe harness or re-
place the door switch.
Replace the ECU.
Repair the harness or re-
place the liftgate switch.
Replace the ECU.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine CHASSIS ELECTRICAL - Theft-alarm System54-223
Trouble symptom
Cause
Check method
Remedy
There is no alarm when, as analarm test, the hood is openedDamaged or disconnected
wiring of hood switch input
If input checks
Repairthe harness or re-
from within the vehicle.circuit.
(P.54-220) indicate aplace the hood switch.
(The alarm is activated, however,malfunction, check by
I
by opening a door or the liftgate.)using check chartMalfunction of the hood p.54-225.
switch.
Malfunction of the ECU.
-Replace the ECU.
Engine would not start [EngineThere is a short-circuit of
starting is possible when the the starter relay activationCheck by using check
chart P.54-234.
Repair the harness.
starter relay is in the switched-off
circuit
(normally closed) condition, with
the clutch switch in the switch-off
and the ECU harness connector
disconnected.]
When, as a test of the alarm, aDamaged or disconnectedCheck by using check
door or the
liftgate is opened wiring of headlight power chart P.54-231, 232.
Repairthe harness or re-
without using the key, orthe hood
is opened from within the vehicle,supply circuit or headlightplace the diode Ds.
activation circuitReplace the headlight
the horn and the theft-alarm hornrelay or the headlight.sound but the headlights don’t
flash. (The headlights can, how-
ever, be switched. ON by usingMa
lfunction of the ECUReplace the ECU.
the passing switch.)The headlights flash during an
alarm test but the horn orthe theftDamaged or disconnectedCheck by using checkRepair the harness.
alarm horn does not sound.wiring of horn relay power
chart P.54-229,230,231.supply circuit or horn ac-Replace the horn.
tivation circuitReplace dedicated fuse
Damaged or disconnectedNo. (6) or the fusible linkwiring of the theft-alarmNo. (6).horn relay power supply
circuit or the theft-alarm
horn activation circuit.
Malfunction of the ECU.
Replace the ECU.The system is not deactivated
nhen, during an alarm test in
Damaged or disconnected
If input checks
which the alarm is intentionallywiring of door key cylinder
Repair the harness.activated, the door or
liftgate isand
liftgate unlock switch(P.54-220) indicate a
input circuitmalfunction, check byReplace the key cylinder
Jnlocked by using the key.
using check chartswitch or the
liftgate
switch.
:The system also cannot be dis-P.54-227,228.
armed.)
Malfunction of door keycyl-inder and liftgate unlock
switch.
Malfunction of the ECU
Replace the ECU.
ECU: Electronic Control Unit
NOTEIf the
lifigate unlock switch or door key cylinder unlock switch is operated roughly, or if these switches have
been installed incorrectly or switches themselves are defective the ECU may not accept the warning or alarmcancelling signal. In such case, the alarm operation will take place when the door is opened using a key.
[When the door key cylinder switch has been shorted, however, if the ignition switch is turned ON, the ECU
judges the detection-switch as faulty and thereafter, it will prevent setting of (warning) alarm until the shorting
is corrected.]
If the
liftgate is opened using a key and is left opened when the door key cylinder switch system has a trouble
(wiring harness damage, open circuit, etc.), the ECU judges it as the
liftgate holding mode and does not producealarm even when the door is opened.
TSB Revision

Downloaded from www.Manualslib.com manuals search engine iCHASSIS ELECTRICAL
- Theft-alarm System54-229
JS!SECURITYE-04@y&fiNAT! ON .$36
152
FUSIBLE LINK CE)m
z0alz!
r%BECATED
mCL
1
TO THE ECUTO THE HORN8. SECURITY LIGHT ACTIVATION CIRCUIT
Description of operation
If all doors are in locked state after key-less locking, the ECUtransistor is turned ON and the security light comes on.
Checking the security light activation circuit (Disconnect the
connector of the ECU and check at the wiring harness side.)Nor-
malMal-
stepCheck objectcondi-func-
Cause
Remedy
tiontion
1D-04connector12v ovterminal voltage 51Fuse (19) dam-Replaceaged or discon-the fusenetted
Harnessdam-Repair the
aged or discon-harnessnetted, or short-circuit
2D-04connector12v ovterminal voltage 52Damaged or dis-
Replaceconnected wiringthe bulbofSECURITYlight bulb
Harness
dam-Repair the
aged or discon-harnessnetted
3ECU terminal volt-12v ovHarnessdam-
age 57Repair the
aged or discon-harnessnetted, or short-circuit9. HORN RELAY POWER-SUPPLY CIRCUIT
Description of operationPower voltage is always supplied to the horn relay.
Checking the horn relay power-supply circuit (Disconnect the
horn relay)
connector terminal
Mal-func-CauseRemedytion
Fuse (3)
dam-Replace the
aged or discon-fusenetted
Damaged or dis-Repair the har-connected har-nessness
TSB Revision

Downloaded from www.Manualslib.com manuals search engine .,i”i, LlNl Q10. HORN ACTIVATION CIRCUIT
?a/ ;
dl
spored10.
Description of operation
The ECU transistor is turned ON if the vehicle door, etc. are
opened without use of the key.
This energizes the horn relay to activate the horn.
Checking the horn activation circuit (Disconnect the connector
of the ECU, then short-circuit terminal connector No.58, and
activate the horn relay.)
54-230CHASSIS ELECTRICAL - Theft-alarm System
z “2
EL? II A-as ’
I3 Ii3
c!
ig”‘“,1 u~cw ~ I A.,Op+J
x
6IZ)Y.l,.-”Step
1Check objectmatMal-
I Icondi- functionCauseRemedy
Horn relay termi-nalvoltage(4-Ground)12v ovMalfunction of
Check thethe horn relayhorn relay
(Refer to
P.54-118.)
Horn terminal volt-12v ovHarnessdam-age (LH & RH)Repair the
aged or discon-harness(1 -Ground)netted
Horn terminal volt-age (LH & RH)(1 -Ground)Nor-
1IItion
HornHornMalfunction ofReplacesoundoesn’tthe hornthe hornds (0 sound
V)(0 w
BatteryDamaged or dis-Repair thevoltageconnected wiringharness
of ground circuit
11. THEFT ALARM HORN RELAY POWER-SUPPLY
CIRCUIT
Description of operation
Power voltage is always supplied to theft alarm horn relay.
Checking the horn relay power-supply circuit (Disconnect the
theft alarm horn relay)Check object
THEFT ALARMHORNRELAYconnector terminal
voltage 1NormalMal-
condi-func-
CauseRemedy
tion
tion
12v
ovFuse (14)
dam-Replace the
aged or discon-fusenetted
Damaged or dis-Repair the har-connected har-nessness
TSB Revision