1994 MAZDA MX-5 coolant

Neutral swltch (MT) 7 PCV valve Powertrain control mod- ule (engine) (PCME) Purge solenoid valve Resonance chamber Steering pressure sen- Stoplight swltch I Throttle posltion sensor r [Two-way check valve Function jetects amount of intake air; sends signal to powertrain :ontrol module (engine) Li~ht illuminates when input device malfunctions - Light flashes to indicate trouble code number of input and output devices Detects in-gear condition; sends signal to powertrain :ontrol module (engine) - Controls blow by aas amount introduced into engine Detects the followlng: 1. A/C operation 2. Airlfuel ratio (Oxygen concentration) 3. Barometric absolute pressure 4. Braking signal 5. Cranking signal 6. EIL operation 7. Engine coolant temperature 8. Engine speed 9. In-gear condition 10. lntake air amount 11, lntake air temperature 12. No.1 piston TDC 13. PIS operation 14. Initial set signal 15. Throttle valve opening angle Controls operatlon of the followlng: 1. AIC (Cut off) 2. Fail-safe function 3. Fuel injection system 4. ldle speed control 5. Ignition timing control system 6. Monitor function 7. Purge control system 8. Lockup control svstem Controls vacuum to pressure regulator -- Adjusts fuel pressure supplied to fuel injectors Controls evaporative fumes from canister to intake man- ifold -- lm~roves mid-ranae torque characteristics -. Detects PIS operation; sends signal to powertrain con- trol module (engine) -- Detects braking operation (deceleration); sends signal to powertrain control module (engine) Reduces HC, CO, and NOx by chemical reaction Controls pressurein fuel tank Controls intake air quantity Detects position of the throttle valve closed throttle posi- tion; sends signal to powertrain control module (engine) Detects the throttle valve opening at a preset angle; sends si~nal to powertrain control module (engine) controls pressure in fuel tank Remark lntake air temperature sensor and fuel pump switch included Use Vref (5 volt) as power source ' Data link connector terminal TEN ' Data link connector terminal TEN Switch ON when in neutral 1, Air conditioning sesnor 2. Heated oxygen sensor 3. Barometric absolute pressure sensor 4. Stoplight switch 5. Ignition switch (START position) 6. Coolant fan relay Light and turn relay Blower switch 7. Engine coolant temperature sensor 8. Crankshaft position sensor (SGT-signal) 9. Neutral and dutch switches (MT) Parklneutral switch (AT) 10. Mass airflow sensor 11, lntake air temperature sensor 12. Crankshaft position sensor (SGC-signal) 13. Steering pressure switch 14. Data link connector 15. Throttle position sensor 1. NC relay 2. Self-diagnosis checker and MIL 3. Fuel injector 4. IAC valve 5. Igniter 6. Monitor lamp (Self-diagnosis checker) 7. Purge solenoid valve 8. Powertrain control module (transmission) (AT) D Controlled by duty signal from powertrain control module (engine) D PIS: ON when steering wheel turned Monolith type D Integrated throttle position sensor, Idle air control valve, and dashpol Gartner Banana

TROUBLESHOOTING GUIDE RELATIONSHIP CHART Fuel injector TEN Terminal (Data link connector) Ignition Switch (Start Position) Steering Pressure Sensor X X X X X X X X X X X X X X X xoo Blower Switch Headlight Switch Stoplight Switch Neutral and Clutch Switches (MT) Parklneutral switch (AT) Air Conditioning Sensor Idle Switch Throttle I BDL) Position Sensor I Sensor (NO) Barometric Absolute Pres- sure Sensor IGF Signal Heated Oxygen Sensor Engine Coolant Temperature Sensor Sensor Mass Air- flow Sensor Intake Air Temperature Sensor Crankshaft SGTSignal Position Sensor SGC-Signal Gartner Banana

TROUBLESHOOTING GUIDE 3 CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) -WHEN ENGINE IS COLD Engine cranks at normal speed but shows partial combustion and will not continue to run IESCRIPTION Battery in normal condition Fuel in tank TROUBLESHOOTING HINTS] B AirIFue! mixture too rich Q Low engine compression Air cleaner element clogged D AirIFuel mixture too lean Fuel injection control malfunction (Correction for coolant temperature) Low fuel line pressure Air leakage of intake air system 1 INSPECTION ACTION :heck if "00" is displayed on Self-Diagnosis Checker ~ith ignition switch ON as page F-79 Sheck if strong blue spark is visible at each discon- iected high-tension lead while cranking engine Connect data link connector terminals F/P and GND with jumper wire and check for correct fuel line pres- sure with ignition switch ON E+T page F-110 Fuel Line pressure: 265--314 kPa I2.7-3.2 kgf/cm2, 38-46 psi) INSTALL CLAPS ' Yes Yes Yes - No - Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page F-81 "88" flashes Check PCME terminal 1 E voltage @f page F-145 Specification: Battery positive voltage (Ignition switch ON) O If OK, replace PCME page F-143 L:, If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Go to next step Check ignition system (Refer to Troubleshooting "Misfire") Section G Go to next step Low pressure Check fuel line pressure while pinching fuel return hose If fuel line pressure quickly increases, check pressure regulator page F-118 o If fuel line pressure gradually increases, check for clog- ging between fuel pump and pressure regulator If not clogged, check fuel pump maximum pressure page F-115 High pressure Check if fuel return hose is clogged or restricted O If OK, replace pressure regulator page F-119 s If not OK, repair or replace Gartner Banana

TROUBLESHOOTING GUIDE 7 CRANKS NORMALLY BUT WILL NOT START (PARTIAL COMBUSTION) -AFTER WARM-UP I ~ngine starts normally when cold TROUBLESHOOTING HINTS] D AirIFuel mixture too rich O Vapor lock Fuel pressure not held in fuel line after engine stops High RVP (winter) fuel used in warm weather 'ESCRIPTIoN Fuel injection control malfunction (Correction for coolant temperature) Fuel injector fuel leakage I INSPECTION Engine cranks at normal speed but shows partial combustion and will not continue to run after running and hol soaked Battery in normal condition :heck if "00" is displayed on Self-Diagnosis Checker with ignition switch ON @S page F-79 :heck if PCME terminal voltages are OK :2D and 20) page F-136 sonnect data link connector terminals F/P and GND ~ith jumper wire and check for correct fuel line pres- sure with ignition switch ON page F-110 Fuel Line pressure: 26-14 kPa {2.7-3.2 kgflcm2, 38-46 psi) GND F~P INSTALL CLAPS ' Yes No - Yes - No Yes ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page F-81 "88" flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) 0 If OK, replace PCME page F-143 0 If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Go to next step Check for cause (Refer to "Check Point for Each Terminal") page F-148 Go to next step Low pressure Check fuel line pressure while pinching fuel return hose Q If fuel line pressure quickly increases, check pressure regulator page F-118 0 If fuel line pressure gradually increases, check fuel line and filter for clogging If not clogged, check fuel pump maximum pressure page F-115 - High pressure Check if fuel return hose is clogged or restricted a If OK, replace pressure regulator page F-119 6 If not OK, repair or replace Gartner Banana

TROUBLESHOOTING GUIDE ESCRIPTION I 0 Engine cranks at normal speed but requires excessive cranking time (more than 5 sec.) before starting Batterv in normal condition 5 I TROUBLESHOOTING HINTS] D Air/Fuel mixture too lean Q Air/Fuel mixture too rich Fuel injection control malfunction Air cleaner element clogged (Correction for coolant temperature) Mass airflow sensor stuck Low fuel line pressure 31 Poor ignition spark CRANKS NORMALLY BUT HARD TO START - ALWAYS Air leakage STEP - 1 INSPECTION Check if "00" is displayed on Self-Diagnosis Checker with ignition switch ON page F-79 Check for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg (17.7 inHg} VA/CUUM GAUGE Check if air cleaner element is clean page F-76 Check for correct fuel line pressure at idle page F-110 Fuel line pressure: 265--314 kPa (2.7-4.2 kgf/cm2, 38--46 psi} (Vacuum hose to pressure regulator discon- nected) INSTALL CLAPS ' - Yes - No - Yes - No - Yes No - Yes - No - ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page F-81 "88" flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) Q If OK, replace PCME page F-143 o If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Go to next step Check for air leakage of intake air system components page F-100 Go to next step Replace air cleaner element page F-99 Go to next step Low pressure Check fuel line pressure while pinching fuel return hose Q If fuel line pressure quickly increases, check pressure regulator page F-118 0 If fuel line pressure gradually increases, check for clog- ging between fuel pump and pressure regulator If not clogged, check fuel pump maximum pressure page F-115 Gartner Banana

TROUBLESHOOTING GUIDE CRANKS NORMALLY BUT HARD TO START - WHEN ENGINE IS COLD c Engine cranks at normal speed but requires excessive cranking time before starting IESCRIPTION Battery in normal condition Restarts OK after warm-up TROUBLESHOOTING HINTS] D AirIFuel mixture too rich Air cleaner element clogged Idle speed control malfunction Q AirJFuel mixture too lean Fuel injection control malfunction (Correction for coolant temperature) O Poor atomization of fuel Low RVP (summer) fuel used in cold weather INSPECTION Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 ACTION - Yes - No - Yes GO to next sGP Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) E+T page F-81 "88" flashes Check PCME terminal 1 E voltage page F-145 Specification : Battery positive voltage (Ignition switch ON) c:, If OK, replace PCME page F-143 o If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Check if PCME terminal voltages are OK (1 C, 2D, 20 and 2Q) page F-145 Go to next step Check for cause (Refer to "Check Point for Each Termi- nal") I@ page F-148 Check if engine starts easily when depressing ac- celerator while cranking Yes Check if idle air control valve is OK @F page F-106 o If OK, check air valve page F-105 6 If not OK, replace IAC valve page F-106 No - Yes - No Go to next step Check for correct intake manifold vacuum at idle Go to next step Vacuum: More than 450 mmHg (17.7 inHg} VACUUM GAUGE / Check for air leakage of intake air system components US= page F-1 00 Check if air cleaner element is clean @&Y page F-76 Yes - No Go to next step Replace air cleaner element page F-99 Try known good PCME and check if condition @&Y page F-144 Yes - No - Replace PCME Change fuel to another brand Gartner Banana

TROUBLESHOOTING GUIDE 9 LOW IDLE SPEEDIROUGH IDLE - BEFORE WARM-UP IESCRIPTION I Engine speed low or engine vibrates excessively at idle during warm-up TROUBLESHOOTING HINTS] D Low intake air amount Mass airflow sensor stuck Air cleaner element clogged Idle s~eed control Q Low fuel injection amount Fuel injection control malfunction (Correction for coolant temperature) O Poor atomization of fuel Air valve [Correction for coolant temperature ] iTEP I Low RVP (summer) fuel used in cold weather INSPECTION ACTION - Yes Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 GOG next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) trs page F-81 - - "88"flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) 0 If OK, replace PCME @ page F-143 e If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON ~8 page F-95 SELECT SW A Yes Go to next step Check if PCME terminal voltaaes are OK No - Yes - No - Yes Lamp not ON/OFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Go to next step " (2D, 20 and 2Q) page F-146 Check for cause (Refer to "Check Point for Each Termi- nal") page F-148 Go to next step Check for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg {I?.? inHg) Check for air leakage of intake air system components @ page F-100 INSTALL CLAPS Gartner Banana

TROUBLESHOOTING GUIDE lo 1 LOW IDLE SPEEDIROUGH IDLE - AFTER WARM-UP 3ESCRIPTION I Engine runs normally at idle during warm-up but vibrates excessively after warm-up ;TROUBLESHOOTING HINTS] I> Idle speed control malfunction b AirlFuel mixture too lean Air leakage of intake air system Low fuel line pressure INSPECTION Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON m? page F-79 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON page F-95 SELECT SW A Disconnect idle air control valve connector at idle and check if engine condition is charged IAC VALVE - Yes No - Yes - No Yes O Air/Fuel mixture too rich Fuel injection control malfunction (Correction for coolant temperature) @ Poor ignition spark Q Low engine compression ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page F-81 "88" flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) 6 If OK, replace PCME page F-143 Q If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Go to next step Lamp not ONIOFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Go to next step Check idle air control valve page F-106 Gartner Banana