1994 MAZDA MX-5 ECU

WINDSHIELD CENTER I SPACER mrn (in) 46UOSX-05( I REPAIR SEALANT mrn {i~ GLASS SEC. A-A % rnrn {in) 45UOSX-052 I V NOTCH GLASS MARK a 4. Securely bond a new dam along the circumference of the glass 7 mm i0.28 in) from the edge. Allow it to dry completely. - 5. Install the spacers onto the body as shown. If a spacer is damaged, replace it. 6. Prepare the nozzle of the sealant tube so that it has a flange that can run along the edge of the glass and a V from which the sealant can flow. Once the primer is dry, apply repair sealant (BOO1 77 739) around the entire cir- cumference to fill the gap between the dam and the edge of the glass with a ridge of sealant 11 mm I0.43 in} high. Keep the bead of sealant smooth and even, reshaping it where necessary with a spatula. 7. If a protector is damaged, securely bond a new protector onto the body as shown. Allow it to dry completely. 8. Install the glass, aligning the glass mark with the V notch in the spacer. Push it in lightly toward the vehicle to corn- press the sealant. 9. To prevent the glass from being pushed out by air pres- sure if a door is closed, open all of the windows until the repair sealant has hardened. Hardening time of repair sealant I Temperature I Surface hardening time ( Time required until car can be PU~ into service I I I 5°C (41 OF) I Approx. 1.5 hr I 12 hr 20°C (68°F) 35°C (95°F) Approx. 1 hr Approx. 10 min 4 hr 2 hr Gartner Banana

s REAR WINDOW GLASS mm {in) I 45UOSX-059 1 , REPAIR SEALANT mm (in) " GLASS UPPER PROTECTOR SEC. A- SIDE PROTECTOR I LOWER PROTECTOR I 45UOSX461 STUD REPAIR SEALANT / 4. Securely bond a new dam along the circumference of the glass 8 mm (0.31 in) from the edge. Allow it to dry completely. i/ 5. Prepare the nozzle of the sealant tube so that it has a flange that can run along the edge of the glass and a V from which the sealant can flow. Once the primer is dry, apply repair sealant (8001 77 739) around the entire cir- cumference to fill the gap between the dam and the edge of the glass with a ridge of sealant 11 mm (0.43 in) high. Keep the bead of sealant smooth and even, reshaping it where necessary with a spatula. 6. If a protector is damaged, securely bond a new protector onto the detachable hardtop as shown. Allow it to dry completely. 7. Align the studs of the glass with the detachable hardtop and mount the glass. 8. Push the glass lightly toward the front to compress the sealant. 9. Tighten the glass mounting nuts. Tightening torque: 2.4--3.3 N-m (24--34 kgf-cm, 20.9-29.5 in-lbf) 10. Use a scraper to smooth away any sealant that oozes out. Add more sealant to any points of poor contact. 11. Install the new rear window molding. (Refer to page S-29.) Hardening time of repair sealant I Temperature I Surface hardening time I Time required until car can be out into service I 8 20°C (68°F) I Approx. 1 hr I 4 hr I I 35°C {95"F) 1 Approx. I0 min I 2 hr I d I I 5°C I41 OF) I Approx. 1.5 hr 12 hr Gartner Banana

DASHBOARD AND CONSOLE - / AIRFLOW MODE WIRE I _ -We -_ -, _ - 11 Center panel assembly The clips are where shown. Adjustment Note Airflow mode wire 1. Set the airflow mode control lever to VENT position. 2. Connect and clamp the wire with the shutter lever on the heater unit at its closest point. 3. Move the airflow mode control lever to make sure the wire is securely attached and that it moves the full stroke from DEF to VENT. REC-FRESH wire 1. Set the selector lever to FRESH position. 2. Connect and clamp the wire with the shutter lever on the blower unit at its closest point. 3. Move the REC-FRESH lever to make sure the wire is securely attached and that it moves the full stroke from - REC to FRESH. TEMF - - I 'ERATURE BLEND WIRE 45UOSX-080 Temperature blend wire 1. Set the temperature blend lever to MAX-HOT position. 2. Connect and clamp the wire with the shutter lever on the heater unit all the way to the right. 3. Move the temperature blend lever to make sure the wire is securely attached and that it moves the full stroke from HOT to COLD. Gartner Banana

CONVERTIBLE TOP s 6. Place the link assembly onto the top fabric. 7. Install the top fabric to the bows, beginning from the rear bow. 8. Align the center of the retainer and the V notch in the top fabric, and roll the top fabric over the bow u retainer. 9. Hang the end of the top fabric on the bow retainer. 10. Clamp the top fabric to the bow with protected water pump pliers. Pull the top fabric by hand to verify that it is held securely. 11. Affix the top fabric to the rear bow with the Velcro. REAR BOW SEC. A-A I pg TOP FABRIC I CENTER BOW 12. Set the convertible top upright. 13. Rivet the cables to the front of the link assembly. Gartner Banana

CONVERTIBLE TOP 26. Install the retainers to the link assembly, aligning the retainer marks with the retainer mounting screws. 27. Install the weatherstri~s to the link assemblv. 28. Install the convertible'to~ to the bodv. (~ef& to paae S-67.) PROTECTOR ADJUSTING NUT WINDSHIELD HEADER CONVERTIBLE TOP I Adjustment Top latch assembly 1. Lift the protector away from the top latch assembly ad- justing nut. 2. Turn the adjusting nut clockwise to decrease clearance A and height B; turn the nut counterclockwise to increase them. 3. Secure the adjusting nut with the protector. Gartner Banana

DETACHABLE HARDTOP PROTECTOR ADJUSTING NUT DETACHABLE HARDTOl WINDSHIELD HEADER I @ 1 5 r 2 (0.2 f 0.08) @ 1 0 r 2 (0 * 0.08) mm (in) 45UOSX-11 f Adjustment Top latch assembly 1. Lift the protector away from the top latch assembly ad- justing nut. d 2. Turn the adjusting nut clockwise to decrease clearance A and height B; turn the nut counterclockwise to increase them. 3. Secure the adjusting nut with the protector. I I Side latch assembly 1. Lift the protector away from the side latch assembly ad- justing nut. 2. Turn the adjusting nut clockwise to tighten the striker and side latch assembly engagement; turn the nut counter- clockwise to loosen the engagement. - 3. Secure the adjusting nut with the protector. ADJUSTING NUT 45UOSX-117 Rear deck latch assembly 1. Remove the screw and open the latch cover. 2. Loosen the plate mounting bolts. 3. Install the detachable hardtop to the body. 4. Move the plate right, left, fore, or aft until it is tight. 5. Tighten the plate mounting bolts. Tightening torque: 18-26 N.m (1.8-2.7 kgfsm, 14--19 ft-lbf) 6. Close the latch cover and install the screw. Gartner Banana

AUDIO 3. Press and hold REW and FF for approximately 2 se- conds until a beep is heard. "Code" will be displayed for approximately 5 seconds and then disappear to indicate that the audio unit is operative. -.- Caution Three consecutive errors, including turning the ignition switch to OFF and disconnecting the au- dio unit, will activate the antitheft system and ren- der the audio unit completely inoperative. If this occurs, contact Panasonic 4. If "Err" (error) appears, repeat the procedure from step 1. TROUBLESHOOTING Before troubleshooting, verify that the customer is using the audio system correctly. If not, advise the customer of the proper operating procedures. (Refer to page T-108.) TY pe 1 1. Speaker(s) do not operate (without headrest speakers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-125 -, 2. Speaker(s) do not operate (with headrest speakers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-127 TY pe 2 1. No sound can be heard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-137 2. Some speakers do not operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-138 3. Bodysonic will not play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-143 Type 1 and Type 2 1. Poor sound quality or noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-131 2. Poor sound quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-133 3. Cassette tape will not load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-134 4. Cassette tape will not play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-135 5. Compact disc will not load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-136 6. Compact disc skips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page T-136 45UOTX-236 Gartner Banana

T SRS AIR BAG SYSTEM I Flowchart No1 I Symptom I Air bag warning light remains ON I Possible cause Poor connection of diagnostic module connector Defective diagnostic module 0 Defective wiring harness CONNECTOR Step 1 Carry out "Before Servicing" procedure under GENER- AL PROCEDURES, page T-160. Step 2 1. Verify that the diagnostic module connector is securely connected to the diagnostic module. 2. Verify that the shorting bar is in the fully retracted posi- tion. 3. If the connector and shorting bar are OK, go to step 3. Step 3 1. Disconnect the diagnostic module connector. 2. Remove the shorting bar from the diagnostic module connector. 3. Check the air bag system warning light. I Llght condltlon 1 Action I I I Illuminate I Repair wiring harness (Instrument cluster - Diagnostic module) I Not illuminate Replace diagnostic module (Refer to page T-208) Gartner Banana