1994 MAZDA MX-5 warning light

RELAY TIMER a 45UOTX-01 FLASHER UNIT Inspection 1. Turn the ianition switch to ON. RETRACTABLE HEADLIGHT RELAY Inspection 1. Disconnect the relay. 2. Apply battery positive voltage and check for continuity .- between terminals of the relay. B+: Batterv ~ositive voltaae Step -- -- M: Continuity Terminal A I H I G I B I D 1 2 3. If not as specified, replace the relay. 2. Operate the following switches and check the operation of the turn signal and hazard warning lights. 0 0 3. If not as specified, troubleshoot the circuit., 0 Switch Turn signal switch Hazard warning switch HAZARD WARNING SW - - 0 Procedure Right side ON Left side ON ON 0 B+ Operation Right turn signal lights flash Left turn signal lights flash All turn signal lights flash 0 GND V Gartner Banana

T INSTRUMENT CLUSTER INSTRUMENT CLUSTER STRUCTURAL VIEW 1. Speedometer 2. Tachometer 3. Water temperature gauge 4. Fuel gauge 5. Oil pressure gauge 6. Warning and indicator lights 7. Trip meter 8. Odometer DESCRIPTION Speedometer Two scales are shown on the speedometer face. The main scale for U.S. specification vehicles is MPH (0-140 MPH); the main scale for Canada specification vehicles is kmlh (0-220 kmlh). The odometer indication is the same as the main scale. Tachometer The tachometer has a RED STRIPED ZONE (6,500-7,000 rpm) that indicates momentary allowable engine speed. The engine should not be operated in the RED ZONE (7,000-8,000 rpm). Fuel Gauge 2 The fuel gauge continues to indicate the amount of fuel remaining in the fuel tank after the ignition switch has been turned OFF. Gartner Banana

T WARNING LIGHT AND SENDER UNIT WARNING LIGHT AND SENDER UNlT STRUCTURAL VIEW 1. Brake system warning light 2. Seat belt warning light 3. Air bag system warning light 4. Retractor indicator light 5. Alternator warning light 6. MIL (malfunction indicator light) 7. O/D OFF indicator light 8. Antilock brake system warning light 9. Washer level indicator light 10. Rear window defroster indicator light Reference Table Warning indicator light SRS air bag system Retractor indicator light Alternator MIL (malfunction indicator light) O/D OFF Antilock brake system Washer level 45UOTX-062 T-34 Reference page or section T-154 T- 48 section G section F section K section P T- 39 J Gartner Banana

WARNING LIGHT AND SENDER UNIT T CIRCUIT DIAGRAM :-a m INSTRUMENT CLUSTER MLiN FUSS LICCd I n L IL/V~~J~,IB/M~W/BIG/LII R IL/V~Y/B[LG ( Y BILIB/Y~ 3 1 R I~/all r IG/R~R/w] B ~G/U~Y/G~G/B 1~ li IJ 91 n 10 w IE to 1~ 11 16 XL ar 11 b 30s a WXidZ.<, A, :-07 PLUlffi BRAKE SUlTCH 11) Gartner Banana

T WARNING LIGHT AND SENDER UNIT TROUBLESHOOTING Check the METER 15A fuse in the fuse box before troubleshooting. If it is burnt, replace it after checking and repairing the wiring harness. i/ Brake System Warning Light I Symptom: Brake system warning light remains illuminated. 45UOTX-063 Step 1 - Check brake fluid level Check brake fluid level. Below MIN I I Check brake system (Refer to section P) I Brake fluid level Action Step 2 - Check parking brake switch 1. Disconnect the parking brake switch connector. 2. Check for continuity between the terminal of the switch and ground. Above MIN Go to Step 2 3. If not as specified, adjust or replace the parking brake switch. (Refer to section P.) 4. If the switch is OK, go to Step 3. I Step 3 - Check brake fluid level sensor I 1. Check for continuity of the sensor. *. 1' Lever Pulled one notch Released Continuity Yes No - I Above MIN No Brake fluid level Below MIN 2. If not as specified, replace the level sensor. 3. If the sensor is OK, repair the wiring harness. Continuity Yes Gartner Banana

WARNING LIGHT AND SENDER UNIT T Symptom: Brake system warning light does not illuminate when parking brake is on. (Ignition switch to ON) 45UOTX-065 Remedy 1. Disconnect the parking brake switch connector. 2. Check for continuity between the terminal of the switch and ground. I Released 1 No I Lever 3. If not as specified, adjust or replace the parking brake switch. 4. If the switch is OK, repair the wiring harness. Continuity 010 OFF Indicator Light Symptom: O/D off indicator light does not illuminate when O/D off switch turned on. 45UOTX-069 Pulled one notch I Yes Symptom: Brake system warning light does not illuminate when brake fluid in reservoir tank is below MIN. 45UOTX-067 Remedy 1. Check the bulb of the O/D off indicator light. 2. If the bulb is burned out, replace it. u Remedy 1. Disconnect the brake fluid level sensor connector. 2. Check for continuity of the brake fluid level sensor. Brake fluid level Below MIN Above MIN Continuity Yes No 3. If not as specified, replace the level sensor. 4. If the sensor is OK, repair the wiring harness. Gartner Banana

T WARNING LIGHT AND SENDER UNIT Remedy 1. Disconnect the timer and buzzer unit connector. 2. Turn the ignition switch ON, and verify that the seat belt warning light illuminates. I Warning light illuminates I Action Seat Belt Warning Light The seat belt warning light is controlled by the timer and buzzer unit. 1 Reolace timer and buzzer unit I Symptom: Seat belt warning light remains on six seconds after ignition switch is turned on. (Timer function does not operate.) I Yes Repair wiring harness (Instrument cluster - Timer and buzzer unit) I d 1 Symptom: Seat belt warning light does not illuminate when ignition switch is first turned on. I 45UOTX-070 Step 1 1. Ground terminal J of the timer and buzzer unit connector. 2. Turn the ignition switch ON, and verify that the seat belt warning light illuminates. 1 Warning light illuminates I Action I Step 2 1. Ground terminal D of the timer and buzzer unit connec- tor. 2. Turn the ianition switch ON. and verifv that the seat belt No Yes warning light illuminates. . Go to Step 2 Repair wiring harness (Timer and buzzer unit - GND) Warning light Illuminates Action Replace timer and buzzer unit Check bulb of seat belt warning light If bulb is OK, repair wiring harness (Instrument cluster - Timer and buzzer unit) Gartner Banana

WARNING LIGHT AND SENDER UNIT T OHMMETER Washer Level Indicator lnspection 1. Disconnect the connector from the washer level sensor. 2. Jump terminal-wire L (harness side) to a body ground. 3. Start the engine and check that the WASHER indicator illuminates. 4. If there is no illumination, check the bulb, wiring harness, and sensor. Replace or repair as necessary. Washer Level Sensor lnspection 1. Connect the sensor connector (sensor side) to an ohm- meter. 2. Move the sensor float up and down. 3. Verify that there is continuity when the float is at the low- est point. BRAKE FLUID LEVEL SENSOR lnspection 1. Check for continuity of the sensor. 2. If continuity is not as specified, replace the level sensor. Float level Below MIN Above MIN BUCKLE SWITCt Continuity Yes No OHMMETER -1 PARKING BRAKE SWITCH lnspection 1. Disconnect the parking brake switch connector. 2. Check for continuity between the switch connector and ground. I Lever I Continuity I 3. If continuity is not as specified, adjust or replace the parking brake switch. (Refer to section P.) Pulled one notch Released BUCKLE SWITCH lnspection 1. Disconnect the buckle switch connector 2. Check for continuity of the switch. Yes No Seat belt I Continuity Seat belt buckled Seat belt unbuckled No Yes 3. If continuity is not as specified, replace the buckle switch. Gartner Banana