1994 MAZDA MX-5 lock

WINDSHIELD WIPER AND WASHER S WINDSHIELD WIPER AND WASHER TROUBLESHOOTING i/ Circuit Diagram WINDSHIELD WIPER & WASHER MAIN FUSE BLOCK MAIN BOA FUSE BLOCK // WIPER \ & 20A IGNITION SWITCH WINDSHIELD WIPER AND WASHER SWITCH i WIPER SWITCH --------------------- o -I MIST o OFF HIGH o o LOW INT I I I - MOTOR - I I I WINDSHIELO WIPER MOTOR ( ( I -01 WINDSHIELD WASHER MOTOR (F) IITHOUT ABS - ----- 'ITH ABS 1-02 WINDSHIELO WIPER MOTOR (F) 1-03 WINDSHIELD WTPER AND WASHER SWITCH(F) Gartner Banana

REAR WINDOW s PUL PROTECTOR Removal Note Rear window 1. Remove the rear package trim. 2. Remove the set plates. 3. Unzip th fully. e rear window, and lower the convertible top 4. Remove the beltline covers. 5. Remove the beltline protectors. 6. Remove the rain rail mounting fasteners from the body. 7. Leave the top latch assemblies in the unlocked position. Raise the convertible top completely. 8. Remove the rain rail from the studs. 9. Remove the rivets from the link assembly with a drill. Drill size: @4.0mm ($0.16 in) 10. Remove the rain rail from the body. Gartner Banana

REAR WINDOW s OUTER RAIN RAIL 9 , BELTLINE COVER PROTECTOR 5. lnstall the zipper stops to the rear window and the top fabric. 6. Affix the rear window to the top fabric with the Velcro. 7. Mount the outer rain rail to the studs. 8. Mount the top fabric to the studs. 9. Mount the rear window to the studs. 10. Mount the inner rain rail to the studs. 11. Loosely install the set plates beginning at the left side. 12. Unzip the rear window, and lower the convertible top fully. 13. lnstall the rain rail with the fasteners. 14. lnstall the beltline protectors. 15. lnstall the beltline cover. 16. Raise the convertible top completely, and lock the top latch assemblies. 17. Zip the rear window into place. 18. Tighten the set plate mounting nuts. Tightening torque: 8.Q-11.7 N.m (90-1 20 kgfem, 79-1 04 ft-lbf) 19. Rivet the top fabric to the link assembly. 20. lnstall the rear package trim. 21. If there is any sagging of the top fabric, remove the pull tab and realign the zipper. Gartner Banana

DASHBOARD AND CONSOLE DASHBOARD AND CONSOLE COMPONENTS Removal l Installation 1. Disconnect the negative battery cable. Warning Handling the air bag module improperly can accidently deploy the air bag, which may seri- ously injure you. Read SERVICE WARNINGS, section T, before handling the air bag module. 2. Remove in the order shown in the figure, referring to Removal Note. To remove the dashboard, remove the control wires of the heater unit and blower unit. 3. Install in the reverse order of removal. 1. Ashtray 2. Change lever knob 3. Rear console assembly a. Back plate b. Shift lever boot 7. Speedometer cable 8. Instrument cluster 9. Center louver Removal Note ............. page S-57 10. Center an el assemblv c. Power window switch Removal Note ............. page S-58 d. Cover (Without power window) 1 1. Glove box assembly e. Console lock assembly 12. Passenger-side airbag module (if equipped) 4. Center lower panel assembly Removal 1 Installation ......... section T Removal Note ............. page S-57 13. Hood release knob -1 5. Steering shaft 14. Center hole cover 6. Meter hood assembly 15. Side cover Removal Note ............. page $57 16. Dashboard Gartner Banana

s SEAT BELT SEAT BELT lnspection ELF? 1. Verify that the belt can be pulled out smoothly, and that d it moves smoothly when worn. 2. Verify that the retractor locks when the belt is quickly pulled. 3. Remove the retractor. 4. Hold the retractor as it would be installed. 5. Slowly incline the retractor while pulling out the belt. 6. Verify that the retractor locks at approximately 30 degrees inclination. Webbing Inspect the webbing for scars, tears, and wear and for deformation of the fittings. BUCKLE SWITCH lnspection 1. Disconnect the seat belt buckle switch connector. 2. Check for continuity between the switch terminals. I Unbuckled I Yes I Seat belt Buckled 3. If continuity is not as specified, replace the switch. Continuity No d Gartner Banana

s CONVERTIBLE TOP PUL BRACKET Removal Note Convertible top 1. Unlock the top latch assemblies. 2. Unzip the rear window, and lower the convertible top \- ' fully. Installation Note Convertible top 1. Insert the rain rail into the beltline molding lip, and mount it over the studs. 2. Align and install the link bracket over the studs with no clearance between the studs and the bracket. 3. Tighten the bolts to the specified torque. Tightening torque: lS--2S N.m (1.9--2.6 kgf.m, l5--18 ftlbf) Gartner Banana

CONVERTIBLE TOP 26. Install the retainers to the link assembly, aligning the retainer marks with the retainer mounting screws. 27. Install the weatherstri~s to the link assemblv. 28. Install the convertible'to~ to the bodv. (~ef& to paae S-67.) PROTECTOR ADJUSTING NUT WINDSHIELD HEADER CONVERTIBLE TOP I Adjustment Top latch assembly 1. Lift the protector away from the top latch assembly ad- justing nut. 2. Turn the adjusting nut clockwise to decrease clearance A and height B; turn the nut counterclockwise to increase them. 3. Secure the adjusting nut with the protector. Gartner Banana

DETACHABLE HARDTOP PROTECTOR ADJUSTING NUT DETACHABLE HARDTOl WINDSHIELD HEADER I @ 1 5 r 2 (0.2 f 0.08) @ 1 0 r 2 (0 * 0.08) mm (in) 45UOSX-11 f Adjustment Top latch assembly 1. Lift the protector away from the top latch assembly ad- justing nut. d 2. Turn the adjusting nut clockwise to decrease clearance A and height B; turn the nut counterclockwise to increase them. 3. Secure the adjusting nut with the protector. I I Side latch assembly 1. Lift the protector away from the side latch assembly ad- justing nut. 2. Turn the adjusting nut clockwise to tighten the striker and side latch assembly engagement; turn the nut counter- clockwise to loosen the engagement. - 3. Secure the adjusting nut with the protector. ADJUSTING NUT 45UOSX-117 Rear deck latch assembly 1. Remove the screw and open the latch cover. 2. Loosen the plate mounting bolts. 3. Install the detachable hardtop to the body. 4. Move the plate right, left, fore, or aft until it is tight. 5. Tighten the plate mounting bolts. Tightening torque: 18-26 N.m (1.8-2.7 kgfsm, 14--19 ft-lbf) 6. Close the latch cover and install the screw. Gartner Banana