1994 MAZDA MX-5 lock

INDEX INDEX 1. Hood Removal I lnstallation . . . . . . . page S- 5 2. Door Removal I lnstallation . . . . . . . page S- 7 Adjustment . . . . . . . . . . . . . . . . page S- 8 3. Window regulator, glass, and guide Removal I lnstallation . . . . . . . page S- 9 Adjustment . . . . . . . . . . . . . . . . page S-10 4. Door lock and opener Removal I lnstallation . . . . . . . page S-15 5. Front bumper Removal I lnstallation . . . . . . . page S-24 6. Molding and garnish Removal I lnstallation . . . . . . . page S-27 7. Outside mirror Structural view . . . . . . . . . . . . . page S-30 Troubleshooting . . . . . . . . . . . . page S-31 lnspection . . . . . . . . . . . . . . . . . page S-33 Removal 1 lnstallation . . . . . . . page S-34 8. Windshield wiper and washer Troubleshooting . . . . . . . . . . . . page $35 Inspection . . . . . . . . . . . . . . . . . page S-38 Removal / lnstallation . . . . . . . page S-39 Disassembly 1 Assembly . . . . page S-43 Adjustment . . . . . . . . . . . . . . . . page S-42 -- 9. Windshield Removal / lnstallation . . . . . . . page S-44 Gartner Banana

INDEX s 1. Trunk lid Removal 1 Installation ....... page S-16 Adjustment ................ page S-17 2. Trunk lid lock and opener Removal / Installation ....... page S-18 Adjustment ................ page S-18 3. Fuel-filler lid opener ....... Removal 1 Installation page S-23 .. 4. Rear bumper w Removal 1 Installation ....... page S-25 Disassembly 1 Assembly .... page S-26 5. Molding and garnish Removal / Installation ....... page S-27 6. Rear window glass (Detachable hardtop) Removal / Installation ....... page S-48 7. Rear window (Convertible top) Removal / Installation ....... page S-52 8. Convertible top Removal / Installation ....... page S-67 Disassembly 1 Assembly .... page S-69 Repair .................... page S-79 Adjustment ................ page S-82 9. Detachable hardtop .... Disassembly 1 Assembly page S-81 Adjustment ................ page S-82 Gartner Banana

HOOD s HOOD COMPONENTS Removal / Installation 1. Remove in the order shown in the figure. 2. Install in the reverse order of removal. 1. Headlight seal 5. Hinge 2. Side headlight seal 6. Hood stay 3. Washer pipe 7. Hood lock 4. Hood Adjustment .................. page S-6 Adjustment .................. page S-6 8. Release wire Gartner Banana

HOOD SEC. 6-6 mm (in) 05UOSX-159 Adjustment Hood Adjust the hood laterally and vertically by loosening the hood to-hinge mounting bolts and repositioning the hood. Hood lock Adjust the hood lock after the hood has been aligned. Loosen the hood lock mounting bolts and nut, and align the lock with the striker on the hood. Gartner Banana

s DOOR FENDER PANEL I DOOR PANEL 5 2 1.0 (0.2 rt 0.04) SEC. A-A mm (in} 05UOSX-o( Adjustment Door lock striker 1. Verify that the door can be closed easily and whether there is any looseness. If there is a problem, loosen the striker mounting screws and adjust by moving the striker vertically. 2. Verify the rear offset of the door to the body. If there is a problem, adjust by moving the door lock striker vertically. Tightening torque: 18-26 N.m (1 .&2.7 kgf.m, 14--19 ftlbf) Door Loosen the hinge bolts and adjust as shown in the figure. Tighten the bolts to the specified torque. Tightening torque: 22-30 N.m (2.2-3.1 kgf-m, 16-22 ftlbf) Door wedge Verify the alignment of door wedge and dovetail. If there is a problem, adjust by moving the door wedge vertically. Tightening torque 4.3-6.2 N-m (43-63 kgf.cm, 37.3-54.7 in.lbf) Gartner Banana

DOOR LOCK AND OPENER s DOOR LOCK AND OPENER COMPONENTS Removal 1 lnstallation 1. Raise the door glass fully. 2. Disconnect the negative battery cable. Note Remove the door screen carefully so that it may be reused. 3. Remove in the order shown in the figure, referring Removal Note. 4. Install in the reverse order of removal, referring Installation Note. 1. Regulator handle 5. Inner handle Removal Note ............. page S-10 6. Sealing pad Installation Note ........... page S-10 7. Door screen - 2. Inner handle cover 8. Door lock assembly 3. Pull handle 9. Outer handle 4. Door trim 10. Key cylinder Removal Note ............. page S-61 Gartner Banana

s TRUNK LID LOCK AND OPENER TRUNK LID LOCK AND OPENER COMPONENTS Removal / Installation 1. Remove in the order shown in the figure. 2. Install in the reverse order of removal. Rear console 6. Rear combination light .................... Removal 1 Installation ....... page S-56 Removal Section T Opener lever 7. Rear finisher ............. Opener cable Removal Note page S-28 4. Trunk end trim 8. Key cylinder 5. Trunk lid lock assembly 9. Striker ..................... Adjustment below Adjustment Trunk lid lock assembly Verify that the trunk lid can be closed easily and that there is no looseness. If necessary, loosen the lock assembly mounting bolts and adjust the lock assembly. Gartner Banana

POWER WINDOW SYSTEM TROUBLESHOOTING Circuit Diagram MAIN FUSE BLOCK e (EI /I \ IX-021 OFF SWITCH FUSE BLOCK K POWER WINDOW SWITCH CLOSE OPEN POWER WINDOWS POWER WINOOW REGULATORS l., -03 POWER WINDOW REGULATOR RH(OR2) -01 POWER WINDOW SWITCH(1) K-02 POWER WiNCOW REGULATO2 LH (ORI) Gartner Banana