1994 MAZDA MX-5 set clock

T AUDIO TYPE 2 AM.FM RADIO UNIT AUTO MEMORY CD EJECT CD SLOT I DISC SET LIGHT- VOLUME CLOCK - / BLANCE BASS - VOLO BA D J I I I I TREBLE ILLUMINATION ONIOFF TAPE SLOT I TREBLE ILLUMINATION ONIOFF I TAPE SLOT DOLBY ALC (AUTO LEVEL CONTROLLER) ROOF MODE ALC ONIOFF BODYSONIC VOLUME ALC INDICATOR LIGHT MUTE 1 FADER MANUAUSEEK - TUNE FAST FOWARDI REWIND - TAPE EJECT PLAY/REVERSE STEREO WIDE I ALC ON + - PW AUTO LEVEL CONTROLLER ONlOFF Gartner Banana

AUDIO OPERATION DESCRIPTION Type 1 Five seconds after completing an operation that is shown on the display, the indicator returns to clock u mode. Radio control 1 Headrest speaker control Bass control knob Treble control knob I Manual tuning button Scan tuning button r- button Auto memory tuning button Illustration Operation 1. Press knob to turn power ON/OFF 2. Turn knob clockwise - Volume up Turn knob counterclockwise-Volume down To increase volume, turn HRSP clockwise I 1. Press BASSiTREBLE 2. For more lows, turn BASSRREBLE clockwise For less lows, turn BASSRREBLE counterclockwise 1. Pull BASSiTREBLE 2. For more highs, turn BASSRREBLE clockwise For less highs, turn BASSRREBLE counterclockwise To shift sound to left, turn BALANCE clockwise To shift sound to right, turn BALANCE counterclockwise Press button to change bands AM, FMl, and FM2 modes are alternatively selected as shown When stereophonic broadcasting is received in FM1 or FM2 mode, ST is shown on display PressV or A less than 0.5 second to manually tune stations When pressed until beep in heard (0.5 sec.), a first receivable frequency is tuned Press A for higher frequency Press V for lower frequency Press SCAN button and searching of station starts from lowest frequency of selected band When receivable frequency is tuned, frequency flashes on display for 5 seconds; then searching starts again Press button again while frequency is flashing to memorize station Six buttons are equipped to set frequencies of up to six stations each for AM, FM, and FM2 1. Setting frequency Select frequency and press a preset button Hold button until deep is heard (1.5 sec.) and setting is complete 2. Tuning to preset frequency Press desired preset button for less than 1.5 seconds 1. Setting frequency Press and hold AUTO-M button until beep is heard (1.5 sec.) Searching starts from lowest frequency within selected band and six strongest stations are selected and memorized 2. Tuning to preset frequency Press AUTO-M button for less than 1.5 seconds and memorized fre- quencies are tuned one by one with each press When preset frequencies is less than six,R appears on display 35UOTX-046 Gartner Banana

AUDIO Name ;can button 3epeat button rrack search button Press SCAN button and beginning of tunes are played one by one (10 seconds for each) Press button during playback and scanning starts from next tune Press button during scanning and tune being scanned is played Scanning is canceled automatically when all programs in disc have been scanned Illustration Press RPT button during a tune is playing to play it repeatedly Press again to cancel repeat operation and resume normal playback Operation Press button to search for beginning of next or current program 1. PressA(up) button for less than 0.5 second during disc play and be- ginning of next tune is selected and played Tunes are changed one by one with each press of button When pressed during play of last tune, first tune is replayed 2. PressV(down) button for less than 0.5 second during disc play and current tune is replayed from beginning Tunes are changed one by one with each press of button When pressed during play of first tune, last tune is replayed Press button to fast forwardheverse disc 1. Press and hold FF (up) button for more than 0.5 second and disc play position moved ahead at high speed while button pressed When last part of last tune is reached, first tune is selected and disc stops 2. Press and hold REV (down) button for opposite operation of FF button When first part of first tune reached, disc stops reversing and starts playing Clock The clock can be set while the radio or tape/CD player is ON. Illustration Clock button (clock display) HIM button (clock setup) Operation Press button to display present radio frequency or operation mode If power supply to unit is broken (burnt fuse or disconnected battery), clock setup will be canceled When clock button is pushed for 2 seconds, clock display flashes. At this point, press H button to advance hours and M button to advance minutes Press clock button again to return to normal display If clock button is pressed again while clock display is flashing and time has not been adjusted (that is, H and M buttons have not been pressed), min- utes will be set at : 00. If time before adjustment showed 30-59 minutes, time will be set at next hour For example, nn Gartner Banana

AUDIO Type 2 AWFM radio Volume control knob F Balance control knob I AM, FM buttons (power switch) - Upldown button Scan tuning button t-- Channel preset tuning button Auto memory button turning Illustration Operation Turn knob clockwise to increase volume Turn knob counterclockwise to decrease volume Turn knob clockwise to shift sound to left Turn knob counterclockwise to shift sound to right 1. With knob original position (bass control) Turn knob clockwise for more bass Turn knob counterclockwise for less bass 2. With knob pulled out (treble control) Turn knob clockwise for more treble Turn knob counterclockwise for less treble 3. To turn audio display off, press knob To turn audio display on, press knob again Press AM or FM button to turn radio power on or off (not necessary to re- move cassette tape or CD) 1. Press AM button to turn AM radio on or off AM radio mode -r AM radio off Other modes + AM radio on 2. Press FM button to move from FM1 1 to FM2 to off Press (A ) or (V ) less than 0.5 second to manually tune stations Press (A ) for higher frequency Press (V ) for lower frequency When pressed more than 0.5 second, frequency search continues until button is released Press button to begin station search from lowest frequency of selected band When receivable frequency is tuned, frequency is displayed for 8 seconds; then searching starts again Press button again while frequency is displayed to memorize station Six buttons are equipped to set frequencies of up six stations each for AM, FMl , and FM2 1. Setting frequency Select frequency and press preset button for more than 1.5 seconds 2. Tuning to preset frequency Press desired preset button for less then 1.5 seconds I. Setting frequency Press button for more than 1.5 seconds Searching starts from lowest frequency within selected band, six stron- gest stations are selected and memorized When preset frequencies are less than six, number of receivable fre- quen ies is shown on display. When there are no receivable frequen- ciesh is displayed 2. Turning to preset frequency Press button repeatedly for less than 1.5 seconds to tune memorized frequencies one by one Gartner Banana

AUDIO Clock The clock can be adjusted during radio, tape, or CD play. I Name I Illustration Clock button (clock display) ALC (Auto level controller) Name 1 Illustration ALCJbodysonic volume control knob I Mute button Roof mode button I Stereo-wide button Operation Press button to display present radio frequency or operation mode If power supply to unit is broken (burnt fuse or disconnected battery), clock setup will be canceled When clock button is pushed for 2 seconds, clock display flashes. At this point, press H button to advance hours and M button to advance minutes Press clock button again to return to normal display If clock button is pressed again while clock display is flashing and time has not been adjusted (that is, H and M buttons have not been pressed), min- utes will be set at :00. If time before adjustment showed 30-59 minutes, time will be set at next hour For example, Operation Press knob to turn ALC on or off 1. At ON, ALC adjusts sound corresponding to vehicle speed; ALC indica- tor light turns on 2. To adjust seat vibration, turn knob to right or left Right -t Seat vibration increases Left + Seat vibration decreases Turn knob right or left to transfer sound Right -+ Door speakers Left -t Headrest speakers Press button to lower overall volume by 10dB Press button to switch between roof-open mode and roof-closed mode; sound quality is adjusted depending on whether roof is opened or closed Press button to turn stereo-wide function on or off At ON, stereo-wide mode improves sound quality Gartner Banana

T SRS AIR BAG SYSTEM 2-PIN CONNECTOR 45UOTX-30E Step 5 Warning Handling the air bag module improperly can acci- ii dently deploy the air bag, which may seriously in- jure you. Read SERVICE WARNINGS, page T-159, before handling the air bag module. 1. Turn the ignition switch to LOCK. 2. Disconnect the negative battery cable. 3. Remove the driver-side air bag module. (Refer to page T-206.) 4. Check if the pin B of the clock spring connector is broken. I Pin B I Action 1 OK I Go to Step 6 I Step 6 1. Connect the clock spring connector. 2. Check if the service code 34 still set. I Code 34 set I Action 1 Broken I Yes I Replace combination switch (Refer to paae T-19) Replace combination switch (Refer to page T-19) 1 -- - No Replace driver-side air bag module (Refer to page T-206) Gartner Banana

T SRS AIR BAG SYSTEM I Flowchart No.9 I Symptom I Service Code 34 I Possible cause Defective air bag module Defective clock spring Defective wiring harness Defective diagnostic module Warning Handling the air bag module improperly can accidently deploy the air bag, which may seri- ously injure you. Read SERVICE WARNINGS, page T-159, before handling the air bag module. Step 1 Carry out "Before Servicing" procedure under GEN- ERAL PROCEDURES, page T-1 60. Step 2 1. Remove the air bag module. 2. Make sure the shorting bars at the diagnostic module connector, clock spring connectors, and air bag module are properly installed. Note An engaged shorting bar or poorly mated connector can cause code 34 to set. 3. Connect the negative battery cable. 4. Turn the ignition switch to ON and check the service code. -- Step 3 1. Turn the ignition switch to LOCK. 2. Disconnect the clock spring connector. 3. Turn the ignition switch to ON and check the service code. Service code 32 34 Action Replace air bag module (Refer to page T-206) Go to Step 3 Step 4 1. Turn the ignition switch to LOCK. 2. Disconnect the negative battery cable. 3. Disconnect the diagnostic module connector. 4. Measure the resistance between terminals 2D (GNV) and 2F (GY) of the diagnostic module connector. Service code 32 Action Replace combination switch (Refer to page T-19) 1 Less than 1 R I Replace wiring harness I Resistance 1 a Action Replace diagnostic module (Refer to page T-208) d Gartner Banana

SRS AIR BAG SYSTEM Possible cause Defective air bag module Defective clock spring Ddfective S-sensor Defective D-sensor Defective diagnostic module Defective wiring harness Service Code 13 Flowchart No.14 Note When fault code 13 sets, the air bag unit blows an internal non-replaceable thermal fuse to prevent accidental deployment of the air bag. The air bag unit must be replaced once code 13 has set, but should not be replaced until the cause for the fault is repaired. Symptom Step 1 Carry out "Before Servicing" procedure under GEN- ERAL PROCEDURES, page T-1 60. Step 2 1. Remove the air bag module. 2. Install a 1 -ohm (rated power 1 W) resistor between termi- nals B and C of the air bag module connector. 3. Connect the negative battery cable. 4. Turn the ignition switch to ON and check the service d 1 code. 1 Other I Go to Step 3 Service code 51 Step 3 1. Turn the ianition switch to LOCK. Action Replace air bag module and then replace diagnostic module 2. ~isconnegt the diagnostic module connector. 3. Check for continuity between terminal 2F (GY) of the diagnostic module connector and ground. I Continuity Action 1 Step 4 1. Disconnect the clock spring connector. 2. Check for continuity between terminal 2F (GY) of the diagnostic module connector and ground. Yes No Continuity Yes Go to Step 4 Go to Step 6 Gartner Banana