1994 MAZDA MX-5 belt

ENGINE TUNE-UP ENGINE TUNE-UP PREPARATION SST I 49 9200 020 Tension gauge, V-ribbed belt For inspection of ignition timing and idle speed For inspection of drive belt tension ENGINE OIL 49 801 9 9AO System selector Warning Continuous exposure with USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water im- mediately after this work. Inspection 1. Be sure the vehicle is on level ground. 2. Warm up the engine to normal operating temperature and stop it. 3. Wait for five minutes. 4. Remove the dipstick and check the oil level and condi- tion. 5. Add or replace oil if necessary. Note The distance between the L and F marks on the dip- stick represents 0.8 L (0.85 US qt, 0.70 Imp qt}. ENGINE COOLANT Inspection Coolant level (engine cold) Warning Removing the radiator cap or the coolant filler cap while the engine is running, or when the engine and radiator are hot is dangerous. Scalding cool- ant and steam can shoot out and cause serious in- jury. It can also damage the engine and cooling system. Turn off the engine and wait until it is cool. Even then, be very careful when removing the cap. Wrap a thick cloth around it and slowly turn it counterclockwise to the first stop. Step back while the pressure escapes. When you're sure all the pressure is gone, press down on the cap-still using a cloth - turn it, and remove it. 1. Verify that the coolant level is near the radiator filler neck. 2. Verify that the coolant level in the coolant reservoir is be- tween the FULL and LOW marks. 3. Add coolant if necessary. Gartner Banana

ENGINE TUNE-UP V-RIBBED BELT PIS or PIS + A/C EQUIPPED AIC EQUIPPED IDLER Coolant quality 1. Verify that there is no buildup of rust or scale around the radiator cap or radiator filler neck. 2. Verify that the coolant is free of oil. d 3. Replace the coolant if necessary. DRIVE BELT Inspection 1. Remove the air intake pipe. 2. Check the drive belts for wear, cracks, and fraying. Re- place if necessary. 3. Verify that the drive belts are correctly mounted on the pulleys. 4. Check the drive belt deflection when the engine is cold, or at least 30 minutes after the engine has stopped. Ap- ply moderate pressure 98 N (10 kgf, 22 Ibf) midway be- tween the specified pulleys. Deflection rnrn {in) Drive belt New' Used Limit Alternator 5.5-7.0 6.0-7.5 m.22-0.27) (0.24-0.29) 8.0 (0.31) t" NC 8.0-9.0 9'0-'0.0 11.5 {0.45} {0.32-0.35) {0.36-0.39) A belt that has been on a running engine for less than five minutes. 5. If the deflection is not within specification, adjust it. 6. Install the air intake pipe. Drive belt tension check Belt tension can be checked in place of belt deflection. Check the drive belt tension when the engine is cold, or at least 30 minutes after the engine has stopped. Using the SST, check the belt tension between any two pulleys. Gartner Banana

ENGINE TUNE-UP B 2 ADJUSTING BOLT LOCKNUT Tension N {kgf, lbfl I Drive belt New* Used I Limit I A belt that has been on a running engine for less than five minutes. 45UOBX-011 Alternator PIS, PIS + A/C AIC Adjustment (1) Alternator belt Loosen the alternator bolts @J and @ and adjust the belt deflection by turning the adjusting bolt 0. Tightening torque @: 19-25 N-m {I .9-2.6 kgf.m, 14-18 ft4bf) @: 38-51 N-m (3.8-5.3 kgf.m, 28-38 ft4bf) 491 -745 (50-76, 11 0-1 67) 491-588 (50-60, 11C-132) 49 1-588 (50-60, 11 0-1 32) (2) PIS belt, PIS + A/C belt Loosen the PIS oil pump bolt @ and nuts @ and @ and adjust the belt deflection by turning the adjusting bolt @. Tightening torque @: 3246 N.m (3.24.7 kgf.m, 24-33 ftlbf) @: 37-53 N-m I3.7-5.5 kgf.m, 27-39 ft4bf) 0: 19-25 N-m {I .9-2.6 kgf.m, 14-18 ft4bf) 491 -706 (50-72, 11 0-1 58) 422-490 (43-50, 95-1 10) 422490 {43-50, 95-1 lo} (3) AIC belt If necessary, loosen the lock nut and adjust the belt deflection by turning the adjusting bolt. 343 (35,771 245 {25, 55) 245 {25,55) Tightening torque: 38-51 N.m (3.8-5.3 kgf.m, 28-38 ft.lbf) Gartner Banana

ENGINE TUNE-UP B lgnition Timing 1. Connect the SST and set the TEST SW to "SELF TEST or connect data link connector terminals TEN and GND with a ium~er wire. ~ 4 2. Check the'idle speed, and set it to specification if neces- sary. (Refer to section F.) ldle speed (Neutral): 800-900 (850 + 50) rpm [MT] (P range): 750-450 (800 + 50) rpm [AT] 3. Verify that the timing mark (White) on the crankshaft pulley and the timing belt cover are aligned. lgnition timing: BTDC 9"-11" (1 0" + 1 ") 4. If the marks are not aligned, loosen the crankshaft posi- tion sensor lock bolt, and turn the crankshaft position sensor to make the adjustment 5. Tighten the crankshaft position sensor lock bolt to the specified torque. Tightening torque: 19-25 N.m {I .9--2.6 kgf.m, 1 &-I8 ft-lbf) 6. Disconnect the SST. 7. Verify that the ignition timing is within the specification. Ignition timing: BTDC 6-18" ldle Speed 1. Connect the SST and set the TEST SW to "SELF-TEST or connect data link connector terminals TEN and GND with a jumper wire. 2. Verify that the idle speed is within specification. ldle speed (Neutral): 800-900 (850 + 50) rpm [MT] (P range): 75-50 (800 -e 50) rpm [AT] 3. If the idle speed is not within specification, remove the blind cap from the air adjusting screw and adjust it. 4. After adjusting the idle speed, install the blind cap and disconnect the SST or jumper wire from the data link connector. Gartner Banana

ON-VEHICLE MAINTENANCE B ON-VEHICLE MAINTENANCE PREPARATION L SST 49 DO11 102 Lock tool, crankshaft Shaft (Part of 49 E011 1AO) Collar (Part of 49 E011 1 AO) Warninq For removal / installat ion of timing belt pulley For prevention of engine rotation For prevention of engine rotation 49 EOl 1 105 Stopper (Part of 49 EOll 1AO) 49 EOll 1 A0 Ring gear brake set For prevention of engine rotation For prevention of engine rotation ~onhuous exposure with USED engine oil has caused skin cancer in laboratory mice. Protect your skin by washing with soap and water immediately after this work. 49 SEO1 310 A Centering tool, clutch disc For installation of clutch disc Gartner Banana

B ON-VEHICLE MAINTENANCE TIMING BELT Removal / lnstallation 1. Disconnect the negative battery cable. 2. Drain the engine coolant. 3. Remove the under cover. 4. Remove in the order shown in the figure, referring to Removal Note. 5. Install in the reverse order of removal, referring to lnstallation Note. (80-110 kgfmn, 7.9-10.7 Nm 13-17 Nm (125-175 kgfcm, 109-151 In4bf) Nm (kgfm, ft4bf) 45UOBX425 1. Air intake pipe 12. Spark plug 2. Upper radiator hose Removal / Installation ......... section G 3. Water hoses (Connected to thermostat 13. PCV valve housing) 14. Cylinder head cover 4. PIS andlor A/C drive belt 15. Upper timing belt cover Removal 1 Installation ....... page B- 6 16. Middle timing belt cover 5. Alternator drive belt 17. Lower timing belt cover Removal / Installation ....... page 5 6 18. Timing belt 6. Water pump pulley Removal Note ............. page B-13 7. Plate Installation Note ........... page B-14 8. Crankshaft pulley Inspection ................. page 8-58 9. Pulley lock bolt 19. Tensioner, tensioner spring Removal Note ............. page B-13 Installation Note ........... page B-14 /' Installation Note ........... page 51 5 Inspection ................. page 558 10. Pulley boss 20. Idler 11. Ignition coil and high-tension lead Inspection ................. page 8-58 Gartner Banana

ON-VEHICLE MAINTENANCE B IDLER L ROTATION ARROW - Removal Note Pulley lock bolt 1. Hold the pulley boss with the SST. 2. Using the SST, loosen the pulley lock bolt. 3. Remove the bolt and the pulley boss. Timing belt 1. Install the pulley boss. 2. Install the pulley lock bolt. 3. Turn the crankshaft to align the timing marks. 4. Do not turn the crankshaft after aligning the timing marks. 5. Remove the pulley lock bolt and pulley boss. 6. Mark the timing belt rotation for proper reinstallation. 7. Loosen the tensioner lock bolt and pry the tensioner out- ward with a bar. 8. Tighten the lock bolt with the tensioner spring fully ex- tended. 9. Remove the timing belt. Gartner Banana

ON-VEHICLE MAINTENANCE Installation Note Tensioner and tensioner spring 1. Install the tensioner and the tensioner spring. 2. Protect the tensioner with a rag. Pry the tensioner out- -,, ward with a bar. 3. Temporarily tighten the tensioner lock bolt with the ten- sioner spring fully extended. Timing belt 1. Verify that the timing belt pulley mark is aligned with the timing mark. 2. Verify that the camshaft pulley marks are aligned with the seal plate marks. E for intake side, and I for exhaust side. 3. Install the timing belt so that there is no looseness at the idler side or between the camshaft pulleys. 4. Install the pulley boss and pulley lock bolt. 5. Turn the crankshaft two turns clockwise and face the pin on the pulley boss upright. Do not turn the crankshaft counterclockwise. 6. Verify that the camshaft pulley marks are again aligned with the seal plate marks. If not aligned, remove the timing belt and repeat from tensioner installation. 7. Turn the crankshaft 1 and 516 turns clockwise and align the timing belt pulley mark with the tension set mark for proper timing belt tension adjustment. 8. Using the SST, loosen the pulley lock bolt and remove the bolt and pulley boss. Do not turn the crankshaft. 9. Verify that the timing belt pulley mark is aligned with the tension set mark. Gartner Banana