1994 MAZDA MX-5 light

LIGHTING SYSTEM T b I Symptom: Interior light@) remains illuminated. (Control switch: DOOR position) 45UOTX-168 Step 1 1. Disconnect the door switch connectors, and check conti- nuity of each switch as shown. 2. If not as specified, replace the door switch. 3. If the switches are OK, go to Step 2. Switch Pushed Released Step 2 1. Close both doors. 2. Disconnect the interior light connectors, and check con- tinuity between terminal wire B (RMI) and ground. Continuity No Yes I No I Replace interior light assembly 1 B+: Battery positive voltage Door Switch Inspection 1. Disconnect the door switch connector, and check conti- nuity of the switch as shown. Terminal B (W) --GND 2. If not as specified, replace the door switch. Continuity yes Switch Pushed Released Action Repair wiring harness (Interior light - Door switch) Continuity No Yes Gartner Banana

nia (i' [-I PACL LIGHT '-6 1.4k HEATER CDNTRCL CONTROL X3 SWITCH SWITCH ILLMI1UATIONS 1 -a? .ILLUMINATION LIGHTS WARNING I CRUISE CCNTQOL ILLVMINATION -0l PANEL LIGHT CONTROL SWITCH (I1 I 1-02 HEATER CONTROL SWITCH ILLGMINA~IONS (11 11-03 ASHTRAY ILLUMINATION (I) H-06 AT SELECT ILLUMINATION(II I -07 HAZARD WAWING AND RETRACTOFi SWITCH ILLUMINATION(II I-oz CRUISE CONTROL MAIN snITcn ILLWINATION (11 E-10 FRONT FOG LIGHT ANO REAR WIMOW DEFROSTER SUITCH ILLUMINATION (I) I Gartner Banana

LIGHTING SYSTEM T Troubleshooting Symptom: Illumination light control does not operate. Remedy 1. Turn the headlight switch ON. 2. Set the panel light control switch to Max. position. 3. Measure the voltage at the following terminal wires of the panel light control switch connector. B+: Battery positive voltage Terminal ( Voltage I Action I OV I Check D terminal Panel Light Control Switch Inspection 1. Remove the panel light control switch. 2. Apply battery positive voltage to terminal D and ground terminal G. 3. Check that the voltage at terminal a changes linearly when turning the control switch. A (R) I Max. ~osition I OV I OV Other Switch 4. If not as specified, replace the panel light control switch. Repair wiring harness (Panel light control switch - Each light) Replace panel light control switch Voltage Min. position 1 OV Gartner Banana

1 mw GRIVER-SIDE AIR BAG MOOULE :-2 SWITCH [a-. .BACK-UP LIGHTS .HORN .STOPLIGHTS .HIGH-MOUNT STOPLIGHT 1 REAR COHeINATION LIGHT '-05 HORN (F) S-03 DRIVEA-SIDE AIR BAG mlDlhE (F) :-06 PASSENGER-SIDE AIR BAG WDULE (F) j-04 PASSENGER-SIDE AIR BAG WOULE (F) Gartner Banana

T HORN Symptom: Horn does not sound. 05UOTX-191 Step 1 1. Check the STOP 15A fuse. 2. If the fuse is burned, replace it. Check and repair the wire harness, if necessary. 3. If the fuse is OK, go to Step 2. Step 2 1. Disconnect the horn connector. 2. Apply battery positive voltage to the horn, and check if the horn sounds. 3. If the horn sounds, go to Step 3. 4. If the horn does not sound, replace the horn. Step 3 1. Remove the knee protector. 2. Ground the terminal B (GIO) of the horn relay connector. 3. If the horn sounds, go to Step 4. 4. If the horn does not sound, go to Step 6. Step 4 1. Disconnect the negative battery cable. 2. Remove the air bag module. (Refer to page T-204.) 3. Check for continuity between the terminal of the horn switch connector and the steering shaft. I OFF I No I Horn switch ON 4. If correct, go to Step 5. 5. If not as specified, replace the horn switch and steering wheel as an assembly. Verify that the air bag system is operating normally by monitoring the air bag warning light. Continuity Yes Gartner Banana

T HORN TURN CLOCKWISE T RETURN 2.75 TURNS +I 2. Remove the air bag module and then remove the steer- ing wheel assembly. d 3. Before installation of the steering wheel reset the clock spring connector as follows: (1) Set the front wheels straight ahead. (2) Turn the clock spring connector clockwise until it stops. (3) Return 2.75 turns. (4) Align the marks (counterclockwise) on the clock spring connector and the outer housing. 4. Install the steering wheel and the air bag module. Verify that the air bag system is operating normally by monitor- ing the air bag warning light. Gartner Banana

FUSE BCOCK IX-031 I 1,05);;;! rAR WINOOW OEFROSTER 1-05 --: RELAY FUSE BLOCK 1-2 .CIGARETTE LIGHTER .INTERIOR LIGHT .REAR WINDOW DEFROSTER MAIN FUSE BLOCK FUSE BLOCK W/R (F) -- ;; ROOM L/R (FI IX-04 'OA &g [x-ZZI 1 - eh FUSE CONTROL MOOUCE (EWGINEI (SECTION 8- tc) INSTRVMENT CLUSTER (SECTION C-a) t OOW SWITCHES (SECTION T) INTERIOR LIGHT OFF. ON !;. (I1 OB CIGARETTE L .IGHTER (I) 1-09 INTERIOR LIGHT (11 I I Z-10 REAR WINOOW DEFROSTER SWITCH (I) I Gartner Banana

T CRUISE CONTROL SYSTEM TROUBLESHOOTING Before troubleshooting the system, check the following items: 1. Is the customer using the system correctly? 2. Is the fuse burnt? If it is, replace it after checking and repairing the wiring harness. d Symptom: Vehicle speed cannot be set. (Cruise control unit will not hold vehicle speed.) 45UOTX-189 ("pj") SRUISE MAIN Step 1 1. Turn the ignition switch ON. 2. Turn the cruise control main switch ON. 3. Check that the main switch indicator light comes ON. 4. If the light does not come ON, go to Step 2. 5. If the light comes ON, go to Step 3. Step 2 1. Check for continuity between the terminals of the cruise control main switch. Neutral OFF I Position M: Continuity 2. If not as specified, replace the switch. 3. If the switch is OK, repair the wiring harness. (METER 15A fuse - Cruise control main switch - GND) Terminal A~B~D~F~G~H Step 3 1. Measure the voltage at the following terminal wires of the cruise control unit connector. Disconnect the CIS control unit connector before measuring the voltage at terminal J. 2. If all terminal voltage are OK, replace the cruise control unit. -- / Gartner Banana