Page 1026 of 1708
SRS AIR BAG SYSTEM i/ Possible cause Poor installation of right D-sensor Defective right D-sensor Defective wiring harness Defective diagnostic module Flowchart No.13 Step 1 Carry out "Before Servicing" procedure under GENER- AL PROCEDURES, page T-160. Step 2 1. Disconnect the diagnostic module connector. 2. Check for continuity between terminal 2J (BRN) of the diagnostic module connector and ground. I Continuity I Action 1 Symptom Service Code 44 Yes No I Yes I Replace wiring harness I Replace diagnostic module (Refer to page T-208) Go to Step 3 .I Step 3 1. Disconnect the right D-sensor connector. 2. Check for continuity between terminal B of the right D- sensor and ground. Continuity Action I No Replace right D-sensor (Refer to page T-210) Gartner Banana
Page 1027 of 1708
T SRS AIR BAG SYSTEM I Flowchart No.14 1 Symptom I Service Code 45 Possible cause Poor installation of center D-sensor Defective center D-sensor Defective wiring harness Defective diagnostic module Step 1 Carry out "Before Servicingw procedure under GENER- AL PROCEDURES, page T-160. No Step 2 1. Disconnect the diagnostic module connector. 2. Check for continuity between terminal 2H (BWW) of the diagnostic module connector and ground. Continuity Action 1 Replace center D-sensor (Refer to page T-210) I - . - No 1 Go to Step 2 I Yes Step 3 1. Disconnect the center D-sensor connector. 2. Check for continuity between terminal B of the center D- sensor and ground. I Continulty Action I Replace diagnostic module (Refer to Dane T-2081 I I Yes I Replace wiring harness I Gartner Banana
Page 1028 of 1708
SRS AIR BAG SYSTEM T Possible cause Poor installation of left D-sensor Defective left D-sensor Defective wiring harness Defective diagnostic module Flowchart No.15 Step 1 Carry out "Before Servicing" procedure under GENER- AL PROCEDURES, page T-160. Step 2 1. Disconnect the diagnostic module connector. 2. Check for continuity between terminal 2E (BR) of the diagnostic module connector and ground. Symptom I Continuity I Action I Service Code 46 Step 3 1. Disconnect the left D-sensor connector. 2. Check for continuity between terminal B of the left D-sen- sor and ground. Yes No Replace diagnostic module (Refer to page T-208) Go to Step 3 I No Replace left D-sensor (Refer to page T-210) Continuity Yes Action Replace wiring harness Gartner Banana
Page 1029 of 1708
T SRS AIR BAG SYSTEM I Flowchart No.16 I Symptom I Service Code 51 I Possible cause Blown internal fuse in diagnostic module (fault conditions no longer present) 0 Diagnostic module not replaced after service code 13 set and conditions corrected. Intermittent short in air bag deployment circuit. Remedy If repairs were made for a service code 13, replace the diagnostic module. If an intermittent short is sus- pected, inspect the wiring harnesses and connectors for damage. If they are not damaged, wiggle the harnesses and connectors to induce the intermittent short; service code 13 will be set when the fault is induced. Then follow the troubleshooting procedure for service code 13. 36EOTX-143 Gartner Banana
Page 1030 of 1708
SRS AIR BAG SYSTEM T Possible cause Defective wiring harness Defective S-sensor Defective diagnostic module Flowchart No.17 Step 1 Carry out "Before Servicing" procedure under GENER- AL PROCEDURES, page T-160. Step 2 1. Disconnect the diagnostic module connector. 2. Check for continuity between terminal 1H (GIB) of the diagnostic module connector and ground. I Continuity Action I Symptom I Yes I Go to Step 3 Service Code 52 Step 3 1. Disconnect the S-sensor connector. 2. Check for continuity between terminal B of the S-sensor and ground. I Continuity I Action I No Replace diagnostic module (Refer to page T-208) Yes No Replace S-sensor (Refer to page T-213) Replace wiring harness Gartner Banana
Page 1031 of 1708
T SRS AIR BAG SYSTEM Possible cause e Damaged diagnostic module Remedy Replace the diagnostic module. (Refer to page T-208) Service Code 53 Flowchart No.18 I Flowchart N0.19 I Symptom ( Service Code 99 Symptom Possible cause Poor connection of all D-sensor and S-sensor Remedy Connect all D-sensor and S-sensor connectors. Gartner Banana
Page 1035 of 1708

T SRS AIR BAG SYSTEM Possible cause ij Defective diagnostic module Defective wiring harness Defective S-sensor Step 1 Carry out "Before Servicing" procedure under GEN- ERAL PROCEDURES, page T-1 60. Service Code 12 Flowchart No.3 Step 2 Check the ENGINE fuse. Fuse Action I Symptom Step 3 1. Disconnect the diagnostic module connector. 2. Connect the negative battery cable. 3. Measure the voltage at terminal 1 L (WIG) of the diagnos- OK Burnt tic module connector. Go to Step 3 Go to Step 4 B+: Battery positive voltage - Other Repair wiring harness iEGI INJ fuss-Diaanostic module1 I Voltage B+ -- ~ Action Replace diagnostic module (Refer to page T-208) I NO Replace diagnostic module (Refer to Daae T-2081 Step 4 1. Disconnect the diagnostic module connector. 2. Check for continuity between terminal 1 H (GIB) of the diagnostic module connector and ground. Step 5 1. Disconnect the orange and blue S-sensor connectors. 2. Check for continuity between terminal 2C (G) of the diag- nostic module connector and ground. 1 Continuity Action 1 Continuity Yes Action Go to Step 5 Yes No Replace wiring harness Go to Step 6 L Gartner Banana
Page 1036 of 1708
SRS AIR BAG SYSTEM Step 6 Check for continuity between terminal 1H (G/B) of the diagnostic module connector and ground. I Flowchart No.4 I Symptom I Service Code 21 I Continuity Yes I No I Replace S-sensor (Refer to page T-213) I Action Replace air bag wiring harness and EGI INJ fuse Possible cause Defective S-sensor Defective wiring harness Defective diagnostic module Step 1 Carry out "Before Servicing" procedure under GEN- ERAL PROCEDURES, page T-1 60. Step 2 1. Disconnect the diagnostic module connector. 2. Check for continuity between terminal 1 E (RIB) of the diagnostic module connector and ground. I Continuitv Action 1 Yes Replace diagnostic module (Refer to page T-208) I NO I GO to step 3 Step 3 1. Disconnect the orange and blue S-sensor connectors. 2. Check for continuity between terminal A of the S-sensor and ground. Continuity 1 Action I 1 yes I Replace wiring harness I I No I Replace S-sensor (Refer to page T-213) I Gartner Banana