1994 Lexus ES300 air condition

IN CASE OF AN EMERGENCY
1342. If required, remove all the vent plugs from the booster
battery. Lay a cloth over the open vents on the booster battery.
(This helps reduce the explosion hazard.)
3. If the engine in the vehicle with the booster battery is not
running, start it and let it run for a few minutes. During jump
starting, run the engine at about 2000 rpm with the accelerator
pedal lightly depressed.
4. Connect the jumper cables in the exact order shown in the
illustration: positive terminal (“+” mark)-to-positive terminal
(“+” mark), and negative terminal (“−” mark)-to-engine or body
ground. Note that you first connect the positive cable to the
discharged battery and then to the booster battery. Next,
connect the negative cable to the booster battery and then to
a solid, stationary, metallic point (e.g. engine hanging hook)
away from the battery. Do not connect it to or near any part that
moves when the engine is cranked.
NOTICE:
When making the connections, do not lean over the
battery or accidentally let the jumper cables or clamps
touch anything except the correct battery terminals or
the ground.
5. Start you, engine in the normal way. After starting, run it at
about 2000 rpm for several minutes with the accelerator pedal
lightly depressed.6. Carefully disconnect the cables in the exact reverse order:
the negative cable and then the positive cable.
7. Carefully dispose of the batten, cover cloth which may now
contain sulfuric acid.
8. If removed, replace all the battery vent plugs.
If the cause of your battery discharging is not apparent (for
example, lights left on), you should have it checked.
IF YOUR VEHICLE OVERHEATS
If your engine coolant temperature gauge indicates
overheating, if you experience a loss of power, or if you
hear a loud knocking or pinging noise, the engine has
probably overheated. You should follow this procedure ...
1. Pull safely off the road, stop the vehicle and turn on your
emergency flashers. Put the transmission in “P” and apply the
parking brake. Turn off the air conditioning if it is being used.
2. If coolant or steam is boiling out of the radiator or reservoir,
stop the engine. Wait until the steam subsides before opening
the hood. If there is no coolant boiling over or steam, leave the
engine running and make sure the engine cooling fan is
operating. If it is not, turn the ignition off.
CAUTION:
To help avoid personal injury, keep the hood closed until
there is no steam. Escaping steam or coolant is a sign of
very high pressure.

IN CASE OF AN EMERGENCY
135 3. Look for obvious coolant leaks from the radiator, hoses, and
under the vehicle. However, note that water draining from the
air conditioning is normal if it has been in use.
CAUTION:
When the engine is running, keep hands and clothing
away from the moving fan and engine drive belts.
4. If the coolant is leaking, stop the engine immediately. Call
a Lexus dealer, Roadside Assistance or Customer Service
Assistance. (See “Foreword”.)
5. If there are no obvious leaks, check the coolant reservoir. If
it is dry, add water to the reservoir while the engine is running.
Fill it about half full.
CAUTION:
Do not attempt to remove engine coolant filler cap when
the engine and radiator are hot. Serious injury could result
from scalding hot fluid and steam blown out under
pressure.
6. After the engine coolant temperature has cooled to normal,
again check the coolant level in the reservoir. If necessary,
bring it up to half full again. Serious coolant loss indicates a
leak in the system. You should have it checked as soon as
possible by your Lexus dealer.
IF YOU HAVE A FLAT TIRE
1. Reduce your speed gradually, keeping a straight line. Move
cautiously off the road to a safe place-well away from the traffic.
Avoid stopping on the center divider of a highway. Park on a
level spot with firm ground.
2. Stop the engine and turn on your emergency flashers.
3. Firmly set the parking brake and put the transmission in “P”.
4. Have everyone get out of the vehicle on the side away from
traffic.
5. Read the following instructions thoroughly.
CAUTION:
When jacking, be sure to observe the following to reduce
the possibility of personal injury:

Follow jacking instructions.

Use a jack only for lifting your vehicle during wheel
changing.

Never get beneath the vehicle when supported by a
jack.

Do not start or run the engine while your vehicle is
supported by a jack.

IN CASE OF AN EMERGENCY
14010. After changing the wheel, check the air pressure of the
replaced tire. Stow all the tools, jack and flat tire securely.
If the pressure of the replaced tire is low, drive slowly to the
nearest service station and fill to the correct pressure.
Do not forget to reinstall the tire valve cap as dirt and moisture
could get into the valve core and possible cause air leakage.
If the cap is missing, put a new one on as soon as possible.
This is the same procedure for changing or rotating your tires.
CAUTION:
Before driving, make sure all the tools, jack and flat tire are
securely in place in their storage location to reduce the
possibility of personal injury during a collision or sudden
braking.
IF YOUR VEHICLE NEEDS
TO BE TOWED
If towing is necessary, we recommend you have it done by
your Lexus dealer or a commercial tow truck service.
Proper equipment will help ensure that your vehicle is not
damaged while being towed. Commercial operators are
generally aware of the state / provincial and local laws
pertaining to towing.Your vehicle can be damaged if it is towed incorrectly. Although
most operators know the correct procedure, it is possible to
make a mistake. To avoid damage to your vehicle, make sure
the following few precautions are observed. If necessary, show
this page to the tow truck driver.
TOWING PRECAUTIONS:
Use a safety chain system for all towing, and abide by the
state / provincial and local laws. The wheels and axle on the
ground must be in good condition. If they are damaged, use a
towing dolly.
1. Using flat bed truck
Lexus recommends this as the best method for your vehicle.