1994 Lexus ES300 In Case Of An Emergency

IN CASE OF AN EMERGENCY
139
8. Reinstall all the wheel nuts finger tight.
Align the holes in the wheel with the bolts. Then lift up the wheel
and get at least the top bolt started through its hole. Wiggle the
tire and press it back over the other bolts.
Reinstall the wheel nuts and tighten them as much as you can
by hand. Press the tire back and see if you can tighten them
more.
Tighten
Tightening torque:
103 N.m
(10.5 kgf-m,76 ft-lb.)
9. Lower the vehicle completely and tighten the wheel
nuts.
Turn the jack handle counterclockwise to lower the vehicle.
Use only the wheel nut wrench to tighten the nuts. Do not use
other tools or any additional leverage other than your hands,
such as a hammer, pipe or your foot. Make sure the wrench is
securely engaged over the nut.
Tighten each nut a little at a time in the order shown. Repeat
the process until all the nuts are tight.
CAUTION:
As soon as possible after changing wheels, have the
wheel nuts tightened by torque wrench at 103 N
.m (10.5
kgf.m, 76 ft.lb.).

IN CASE OF AN EMERGENCY
14010. After changing the wheel, check the air pressure of the
replaced tire. Stow all the tools, jack and flat tire securely.
If the pressure of the replaced tire is low, drive slowly to the
nearest service station and fill to the correct pressure.
Do not forget to reinstall the tire valve cap as dirt and moisture
could get into the valve core and possible cause air leakage.
If the cap is missing, put a new one on as soon as possible.
This is the same procedure for changing or rotating your tires.
CAUTION:
Before driving, make sure all the tools, jack and flat tire are
securely in place in their storage location to reduce the
possibility of personal injury during a collision or sudden
braking.
IF YOUR VEHICLE NEEDS
TO BE TOWED
If towing is necessary, we recommend you have it done by
your Lexus dealer or a commercial tow truck service.
Proper equipment will help ensure that your vehicle is not
damaged while being towed. Commercial operators are
generally aware of the state / provincial and local laws
pertaining to towing.Your vehicle can be damaged if it is towed incorrectly. Although
most operators know the correct procedure, it is possible to
make a mistake. To avoid damage to your vehicle, make sure
the following few precautions are observed. If necessary, show
this page to the tow truck driver.
TOWING PRECAUTIONS:
Use a safety chain system for all towing, and abide by the
state / provincial and local laws. The wheels and axle on the
ground must be in good condition. If they are damaged, use a
towing dolly.
1. Using flat bed truck
Lexus recommends this as the best method for your vehicle.

IN CASE OF AN EMERGENCY
141
Tie down points
Front
If your Lexus is transported by a flat bed, it should be tied
down at locations A and B as shown above.
Rear emergency
towing eyelets
NOTICE:
Do not use rear emergency towing eyelets.

Tie down angle
If you use chains or wires to tie down your vehicle, the
angle must be as shown above.

IN CASE OF AN EMERGENCY
1422. Towing with wheel lift type truck

From front
Release the parking brake.

From rear
Use a towing dolly under the front wheels.
NOTICE:
Never tow s vehicle with an automatic transmission from
the rear with the front wheels on the ground, as this may
cause serious damage to the transmission.
3. Towing with sling type truck
NOTICE:
Do not tow with a sling type truck, either from the front
or rear. This may cause body damage.

IN CASE OF AN EMERGENCY
143
Emergency towing
Emergency towing eyeletsEmergency towing eyelets
If towing service is not available in an emergency, your
vehicle may be temporarily towed by a cable secured to
one of the eyelets under the front or rear of the vehicle.
A driver must be in the vehicle to steer it and operate the
brakes. Towing in this manner may be done only on
hard-surfaced roads for a short distance and at low speeds.
Also, the wheels, axles, drive train, steering and brakes must
all be in good condition.
Before towing, release the parking brake and put the
transmission in “N”. The ignition key must he in “ACC” (engine
off) or “ON” (engine running).CAUTION:
If the engine is not running, the power assist for the brakes
and steering will not work so steering and braking will be
much harder than usual.
IF YOU CANNOT SHIFT THE
AUTOMATIC TRANSMISSION
SELECTOR LEVER
Lock
Cover of shift lock
override button
If you cannot shift the selector lever out of “P” position to
other positions even though the brake pedal is depressed,
use the shift lock override button as follows:
1. Turn the ignition key to “LOCK”. Make sure the parking
brake is applied.
2. Pry up the cover with a flat-bladed screwdriver or
equivalent.

IN CASE OF AN EMERGENCY
144
3. Insert the screwdriver or equivalent into the hole to push
down the shift lock override button. You can shift out of “P”
position only while pushing the button.
4. Shift into “N” position.
5. Insert the cover.
6. Start the engine. For your safety, keep the brake pedal
depressed.
Be sure to have the system checked by your Lexus dealer as
soon as possible.
IF YOU LOSE YOUR KEYS OR
LOCK YOURSELF OUT
If you need replacement of an ignition key, contact your
Lexus dealer.
See the suggestion given in “Keys” on page 8.
If your keys are locked in the vehicle and you cannot get a
duplicate, many Lexus dealers can assist you. If you must
break a window to get in, we suggest breaking the smallest
side window because it is the least expensive to replace. Be
extremely cautious to avoid cuts from the glass.