Security System - RESTRICTED ISSUE 84
4!sw
A5.15 SECURITY SIREN
(12 CYL) - RENEW
SRO 86.52.03
= Open the trunk and remove the battery cover.
Disconnect the battery ground lead.
Open the hood and remove the headlamp
/ relay cover.
See
SRO 76.1 1.22, Section 13.
Remove the RH air cleaner element. See SRO 19.10.11, Section 5.2.
Remove the RH air cleaner assembly. See SRO 19.10.02, Section 5.2.
. Identify the RH forward harness relays (1 Fig. 1) for subse- quent refitting. Remove the relays and relay bases from
the mounting bracket.
. Disconnect the siren harness multi-plug (2 Fig. 1).
rn Reposition the side harness (3 Fig. 1) to gain access to the
. Undo the siren securing bolts (1 Fig. 2) and remove the
Note:
. Remove the captive washers and the siren securing bolts.
. Fit the siren securing bolts to a new siren.
. Fit and fully seat the captive washers.
. Align the siren securing bolts to the vehicle chassis.
Refitting the remaining components is the reverse of the re
-
moval procedure.
siren securing bolts.
siren
(2 Fig. 2).
The siren securing bolts remain captive.
Tighten the siren securing bolts.
AS. 16 SECURIN SIREN (6 CYL) - RENEW
SRO 8652.03
. Open the trunk and remove the battery cover.
rn Disconnect the battery ground lead.
. Open the hood and remove the headlamp / relay cover.
See SRO 76.1 1.22, Section 13.
. Identify the RH forward harness relays for subsequent re- fitting. Removethe relays and relay bases from the mount- ing bracket.
. Disconnect the siren harness multi-plug.
Reposition the side harness to gain access to the siren se-
. Undo the siren securing bolts and remove the siren.
curing
bolts.
The siren securing bolts remain captive.
Remove the captive washers and the siren securing bolts.
. Fit the siren securing bolts to a new siren.
. Fit and fully seat the captive washers.
= Align the siren securing bolts to the vehicle chassis.
Refitting the remaining components is the reverse of the re
-
moval procedure.
Tighten
the siren securing bolts.
Fig. 1
Fig. 2
X300 VSM Issue 1 August 1994 42
Security System - RESTRICTED ISSUE 84
-
A5.18 REAR DOOR LOCKASS€MBLY - RENEW
SRO 86.25.47
. Remove the veneer trim pad. See Section 13 of the VSM.
. Remove the upper trim pad. See Section 13 of the VSM.
. Remove the lower trim pad. See Section 13 of the VSM.
. Using a suitable plastic knife, cut through the weathershield to door sealant and pull back the weathershield for ac-
. Cut and remove the securing tie-wrap from the door lock assembly harness multi-plug.
Displace and reposition the door lock assembly multi-plug from the mounting bracket and disconnect.
Disconnect the door handle link rod.
. Disconnect and remove the door sill button link rod.
= Undo and remove the door lock assembly securing bolts.
. Undo and remove the lower securing bolt from the glass frame.
Displace and reposition the door lock assembly into the bottom of the door.
Displace and remove the edge clip from the door handle release cable.
. Displace and reposition the door handle release cable.
9 Displace and remove the door lock assembly.
cess
to the door lock assembly.
A5.19 TRUNKLIDLOCKACTUATOR- RENEW
SRO 86.25.49
. Open the trunk lid.
. Remove the luggage compartment lamp assembly. See Section 15 of the VSM.
Displace and remove the trunk lid liner fasteners and reposition for access.
. Undo and remove actuator mounting bracket securing bolts.
Disconnect the actuator to lock mechanism link rod.
. Remove the actuator and motor.
Undo and remove the actuator to mounting bracket securing screws.
Fitting
a new actuator is the reverse of the removal procedure.
Disconnect
the actuator harness
multi-plug.
15.20 CLOCKMODULE- RENEW
SRO 86.80.13
. Remove centre console ashtray and veneer panel., refer to VSM, section 13.
. Release and remove gear selector illumination module securing screws.
. Re-position illumination module as necessary for removal of radio console.
= Release radio console securing screws, partially withdraw radio console from center console so that console harness
and radio aerial connectors can be removed.
. Release radio ground lead from securing nut.
. Remove dedicated radio harness connector from multi-plug.
. Fully withdraw radio console and remove radio unit.
Release securing screws and remove clock module.
15.21 READER EXCITER COIL AND MODULE - RENW
. Access to the reader exciter coil is gained by removing top and bottom ignition cowls, refer to VSM, Section 13 for
The exciter coil is mounted around the ignition switch and can be removed by releasing spring tension coil clips.
. The module is mounted on the steering column assembly, secured by two bolts.
. To remove the module disconnect the harness multi-plug and remove the securing bolts.
remove
/ refit instructions.
X300 VSM Issue 1 August 1994 44
