1994 JAGUAR XJ wiring

ZF Automatic Transmissions Service Manual
a
2.3.6 Fault Finding Chart (continued)
Problem
Starter motor does not operate
'osition 'R' - Reverse
3everse gear inoperative
Slipping and juddering
Harsh
engagement'p-R' chan
'N-R' change (below 1500RPF
engine speed)
Reverse lamp does not
illuminate (bulbs, fuses and
cables functioning correctly)
Possible Cause
Rotary switch adjustment.
Rotary switch wiring fault.
Rotary switch faulty.
Position
'P or 'N' not selected.
vIV2 faulty.
rNire to MV2 earthed.
3il filter dirty.
Damper
'6' faulty.
Clutch
'6' faulty (also no 3rd gear).
Clutch 'D' faulty.
Clutch
'E' faulty (also no engine braking
in 2nd and 3rd gears).
Pressure regulator valve 1 binding
Rotary switch wiring fault.
Rotary switch faulty.
Reverse gear inhibit valve activated.
Main pressure control valve seized (also
no forward drive in 'D' Drive).
'B'Clutch, 'D'Clutch or 'E' Clutch faulty.
Pressure regulator valve 1 binding
'F'Clutch drum sealing rings faulty
causing
loss of 'E' Clutch pressure.
Damper
'6' faulty (also no 2nd to 3rd
shift).
Pressure regulator valve 1 binding
Modulation pressure too high.
Rotary switch faulty.
Rotary switch setting incorrect.
Rotary switch faulty.
Rotary switch wiring fault.
Action
4djust switch.
qectify.
3ectify or renew.
Select 'F" or 'N'.
Renew valve block.
Renew harness.
Clean
/ replace filter and flush out
the
oil cooler and pipes.
Renew valve block.
Renew transmission.
Renew transmission.
Renew transmission.
Renew valve block.
Rectify.
Rectify or renew.
Renew valve block.
Renew valve block.
Renew transmission.
Renew valve block.
Renew transmission.
Renew valve block.
Renew valve block.
Check TCM Fault Codes.
Rectify or renew.
Adjust setting.
Renew.
Rectify.
Issue 1 August 1994 62

ZF Automatic Transmissions Service Manual
Problem Possible Cause
2.3.6 Fault Finding Chart (continued)
e Action
Starter will not operate Rotary
switch faulty or incorrect setting. Rectify
or renew.
3rive not transmitted (neutral
:ondition)
Vehicle moves
Slipping and juddering at start Rotary
switch wiring fault. Rectify 'A'Clutch seized Renew
transmission
Checksecurity System
Harsh engagement
'N'-'D'(under 1500RPM engine
speed)
No 1st to 2nd upshift or 2nd to
1st downshift
No upshift 1st to 2nd
No upshift 2nd to 3rd or
downshift 3rd to 2nd
No upshift 2nd to 3rd
3il filter dirty.
Main pressure control valve seized.
Low oil level.
'A'Clutch faulty.
'D'Clutch one-way clutch slips. ~
'A'Clutch faulty
Low oil level.
'A'Clutch faulty.
'A'Clutch damper faulty (5).
Throttle pot. volts high.
Rotary switch faulty
/ out of adjustment.
MVI wire earthed(remains in 2nd gear).
MVI faulty.
Control circuit fault.
Shift valve
1-2 seized.
Pressure reducing valve
1 seized.
Speed sensor or connectors faulty.
Clutches
'Cl' and 'C' faulty
MV2 wire earthed (remains in 2nd gear).
MV2 faulty.
Shift valve 2
-3 seized.
Speed sensor faulty.
'B'Clutch faulty Clean
/ replace
filter.
Renew valve block.
Check oil level.
Renew transmission.
Renew transmission.
Renew transmission.
Check oil level.
Renew transmission.
Renew valve block.
Check throttle pot. volts.
Rectify or renew.
Renew harness.
Renew valve block.
Check TCM Diagnostics
/ rectify.
Renew valve block.
Renew valve block.
Check connections, rectify or
renew.
Renew transmission
Renew harness.
Renew valve block.
Renew valve block.
Rectify or renew.
Renew transmission
Issue 1 August 1994 63

ZF Automatic Transmissions Service Manual
No engine braking
Manual gearchange 3rd to 2nd
inoperative Clutch 'Cl' or
Clutch 'E' faulty
Speed sensor faulty.
MV2 faulty.
a
Renew transmission
Check TCM Diagnostics
1 renew
speed sensor.
Renew valve block.
a
0
Problem
Vo 'kick-down' change
Light throttle speeds only
Light throttle gear change too
hard
1st to
2nd, 2nd to 3rd and 3rd to
4th changes too long
Full load and 'kick
-down'
changes too long
Full load and 'kick
-down'
changes too hard ~
Possible Cause
'Kick-down'
switch out of adjustment 1
full throttle stop adjustment.
'Kick
-down' switch faulty.
'Kick
-down' switch connector or wiring
Fa u Ity.
TCM faulty
Valve block bolt torque incorrect.
Modulation pressure too high.
Damper faulty.
Clutch plates faulty.
Valve block bolt torque incorrect.
Damper faulty.
PRSV faulty.
PRSV wire earthed.
Modulation valve seized.
Pressure regulator valves
1 and 2 seized.
mve block bolt torque incorrect.
Modulation pressure too low.
Clutch plates faulty.
Valve block bolt torque incorrect.
Modulation pressure too low.
Clutch plates faulty.
Action
Adjust as per Engine Set Up
procedure on JDS.
Renew 'kick
-down' switch.
Rectify.
Check TCM
Reset to correct torque.
Renew valve block.
Renew valve block.
Renew gear unit.
Reset to correct torque.
Renew valve block.
Renew valve block.
Renew harness.
Renew valve block.
Renew valve block.
Reset to correct torque.
Renew valve block.
Renew transmission.
Reset to correct torque.
Renew valve block.
Renew transmission.
issue 1 August 1994 65