1994 JAGUAR XJ check engine

AJ16 Engine Service Manual
1 Clean and polish the crankshaft journals, lubricate and
carefully assemble the crankshaft into the cylinder block,
fit the thrust washers ensuring that the steel side of the
washer is mated to the cylinder block (1 Fig. 1).
1 Rotate the crankshaft to ensure that it turns freely.
1 Fit the main bearing shells into the main bearing caps, lu- bricate and fit to the cylinder block.
1 Start the securing bolts and carefullytap the main bearing
caps to ensure they are seated to the cylinder block.
1 Rotate thecrankshaft to ensurethat it still turnsfreely, pull
down each bearing cap individuallyand torque tighten the
securing bolts.
1 Rotate the crankshaft between pulling down each bearing
cap.
1 Check and if necessary adjust the crankshaft end-float in
accordance with Section 4.12.
1 Renew the crankshaft rear oil seal, see Section 4.14.
1 Fit a new bearing shell to the connecting rod, lubricate
1 Fit a bearing shell to theconnecting rod bearing cap, lubri-
with clean engine oil and fit to the crankshaft.
cate and fit to the connecting rod.
Fit and torque tighten
1 Turn the crankshaft over ensuring that there are no 'tiaht'
the nuts.
spots, and that the crankshaft rotates freely.
-
1 Repeat this procedure for the remaining five cylinders.
WUTION: The connecting rod bearing nuts, bolts and
main bearing securing bolts MUST be renewed during assembly and torque tightened as de- scribed in Section 2.1, SPS Joint Control Sys- tem.
1 Clean and inspect for wear or damage all the timing gears,
chains, guides and tensioners.
1 Renew any suspect component.
1 Fit and seat the crankshaft sprocket woodruff key and fit the sprocket to the crankshaft.
1 Refit the timing chains - upper and lower; and the upper
and lower tensioners, see Section 4.19.
1 Fit a dial gauge to the top ofthe cylinder blockand turn the
engine over until No.1 and 6 pistons are at TDC (Fig. 2).
1 Lubricate the upper chain and fit it to the intermediate
sprocket.
0 1 Fit an elastic band to retain the upper dampers and chain.
. Lubricate the oil pump drive chain, fit the chain to the
crankshaft sprocket and lodge in the correct position.
1 Renew the timing cover oil seal and refit the timing cover.
. Lubricate and fit the oil seal distance piece. Fit and seatthe
1 Refit the oil pump, see Section 4.31.
1 Refit the flywheel (Manual), see Section 4.15, or refit the
1 Refit the oil pan, see Section 4.27.
1 Refit the crankshaft damper /pulley assembly, see Section
1 Refit the cylinder head, see Section 4.4.
1 Remove the engine from the stand and refit the trans-
1 Refit the engine/transmission unitto thevehicle, see Sec-
damper woodruff key.
drive
-plate (Automatic), see Section 4.16.
4.11.
mission unit.
tion
3.1 in the appropriate Vehicle Service Manual.. Fig.
1
Fig. 2
Issue 1 August 1994 25

AJ16 Engine Service Manual
4.12
SRO 12.21.26
Crankshaft End-float, Check and A4ust
Remove components as required for access and proceed as
follows.
Remove the oil pan, see Section 4.27.
Remove the oil pump pick-up pipes (3 Fig. I), see Section
Remove the crankshaft windage trays (6 Fig. 1).
. Mount a suitable dial gauge and position the stylus on the
crankshaft front pulley.
. Zero the gauge, and with the use of a suitable lever,
measure the crankshaft end-float (Fig. 2). For the correct
end-float, see Service Data in the Preliminary Pages.
If the end-float exceeds the tolerances, remove the center
main bearing cap, and renew the thrust washers.
&&: When refitting the thrust washers, ensure that the
bearing face (grooved) (1 Fig. 3) and not the steel
side contacts the crankshaft.
. Recheck the end-float and if satisfactory, clean the main
bearing cap and bearing, lubricate with clean engine oil
and
fit the cap assembly to the cylinder block.
4.28. 0
Fit and
torque tighten the securing bolts.
CAUTION: The main bearing securing bolts MUST be re
-
newed during assembly and torque tightened as described in Section 2.1, SPS Joint Control
System.
Ensure that the bearing cap is the correct way round
with the cap numbers corresponding to the
numbers stamped on the oil pan mounting face.
Rotate the crankshaft to ensure that it is not being
'pinched' and will rotate freely.
m Remove the dial gauge and torque tighten the main bear- ing cap. Refit the windage trays to the cylinder block and
secure with the bolts.
w:
Refit the oil pump pick-up pipes, see Section 4.28.
Refit the oil pan, see Section 4.27.
Refit the oil filler / drain back tube.
Replace the components removed for access.
0
3
Fia. 1
Fig. 2
Fig.
3
27 Issue 1 August 1994

AJ16 Engine Service Manual
4.16 Engine Driveplate, Renew
SRO 12.53.13
1 Remove the transmission unit.
Remove the drive-plate securing bolts (1 Fig. 1).
Remove the drive-plate (2 Fig. 1).
. Check the crankshaft rear oil seal for leaking, renew as
Fit the new drive-plate to the crankshaft. Fit and tighten
1 Refit the transmission unit.
necessary,
see Section
4.14.
the securing bolts.
I Fin. 1
Issue 1 August 1994 31

AJ16 Engine Service Manual
4.18 &;ne Assembly, Overhaul
SRO 12.41.05
. Remove the engine and transmission unit, see Section 3.1
. Remove the transmission unit from the engine.
. Fit the engine to a stand.
. Place a drain tray belowthe cylinder block drain plug and
Overhaul the cylinder head, see Section 4.5.
1 Remove the oil pan, see Section 4.27.
. Remove the oil pump, see Section 4.31.
. Remove the windage trays.
. Clean all components, check for damage and wear and
. Remove the rear oil seal housing, see Section 4.1 4.
. Remove the timing cover assembly.
1 Remove the pedestal bolts and tab washer.
. Remove the pedestal / tensioner assembly and damper.
Slacken off the oil pump drive chain damper securing
bolts and move the damper clear of the chain. Push back
the lock tabs
(1 Fig. 1) and remove the securing bolts (2
Fig. 1) from the oil pump drive sprocket (3 Fig. 1).
in the appropriate Vehicle Service Manual.
drain any remaining coolant from the engine.
renew as required.
. Remove the drive sprocket and shim pack.
. Remove the oil pump drive chain (5 Fig. l), remove the
elastic band from the upper dampers and remove the
upper timing chain.
1 Remove the lower tensioner securing bolts and remove
the tensioner.
. Push back the lower chain fixed damper securing bolt lock
tabs and remove the bolts.
. Remove the damper and tab washer.
. Repeat for the remaining fixed and pivot dampers and re- move the lower chain and intermediate sprocket.
Remove the crankshaft pulley spacer and the crankshaft
pulley woodruff key.
= Remove the drive sprockets and woodruff keys from the
crankshaft.
1 Checkall drive sprocketsforwear, distortion and damaged
teeth. Renew as required.
. Remove the power assisted steering pump assembly, see
Section 10 in the appropriate Vehicle Service Manual and
reposition away from the timing cover area.
. Renew the auxiliary shaft, see Section 4.24.
1 Renew the auxiliary shaft bushes, see Section 4.19.
1 Remove the oil pump drive chain damper.
. Remove the spacers from behind the damper.
. Remove the pistons and connecting rods and renew, see
Section 4.7.
. Refit the connecting rod bearing shells to one connecting
rod and cap and fit the rod to the crankshaft. Torque
tighten
the nuts and checkthe side clearance between the end face of the rod and the journal shoulder (Fig. 2) -see
Service Data in the Preliminary Pages.
Remove the connecting rod from the crankshaft.
. Repeat for the remaining five connecting rods. Fig.
1
Fig. 2
Issue 1 August 1994 33

AJ16 Engine Service Manual
CAUTION: The connecting rod bearing nuts, bolts and
main bearing securing bolts MUST be renewed during assembly and torque tightened as de- scribed in Section 2.1, SPS Joint Control Sys- tem.
. Ensuring that the main bearing caps are marked relative
to the cylinder block, remove the main bearing cap bolts
and remove the caps. Carefully
lift out the crankshaft.
Place the crankshaft
on suitable blocks on a bench. Re- move and discard the bearing shells and the thrust
washers. Clean the cylinder block, crankshaft and bearing
caps.
. Check the crankshaft journals for wear and ovality, for tol- erances - see Service Data in the Preliminary Pages.
. If any ofthe dimensions are outside the stated tolerances,
then the Crankshaft must be renewed.
Fit suitable bolts to the oil gallery plugs and pull to remove
(Fig.
1 ). Check all cylinder block oil galleries for cracks and
blockages. Fit new '0' rings to the oil gallew plugs, lubri- cate the '0' rings and fit the plugs to the cylinder block oil
galleries.
Check all bearing housings for cracks, distortion and any
signs of bearing movement, i.e. scoring or overheating,
renew as necessary.
Checkthecylinder block/cylinder head mating surface for
warping, bowing and cracks.
Check the bore wear in the cylinder block with a suitable
comparator (Fig.
2). This must be done in at least six posi- tions in the bore (Fig. 3).
Maximum bore wear normally occurs towards the
top of the bore, across its thrust axis.
If standard size replacement pistons are being fitted,
they must bethesamegradeasthe markingsonthe
cylinder block.
If new piston
ringsare being fitted without reboring,
de-glaze the cylinder bores using a hone or glaze buster. This operation will not increase the size of
the bores and will givethe bores across-hatchedfin- ish.
&&:
m:
b:
Fia. 1
Fig. 2
1
m2 3
,!I 25s
Fig. 3
34 Issue 1 August 1994

AJ16 Engine Service Manual
0 1 Insert each new piston ring into the cylinder bore, (1 Fig. 1) ensuring they are square in the cylinders and checkthe gap using a strip gauge (2 Fig. 1).
. If the gap is insufficient, then a small flat file or carborun- dum stone can be used on the butting ends of the ring. En- sure that after filing no burrs remain.
Ensure that the rings are not inter
-mixed after they
have been gapped and that each piston/ring assem- bly is matched to its respective bore.
Measure the piston skirt clearance using a long strip
gauge. Insert the strip gauge down the right-hand side of
the cylinder bore, insert the correct piston INVERTED into
the bore (with the piston pin parallel to the axis of the
crankshaft).
. Push the piston down the cylinder until it reaches its
tightest point in the bore. At this point, withdraw the strip
gauge; a steady resistance should be felt.
1 If the tolerances are outside those given in Service Data in
the Preliminary Pages, the pistons must be renewed as a
complete set.
Note:
0
Fit the new main bearing shell halves to the cylinder block
and lubricate with clean engine oil.
1 Clean and polish the crankshaft journals (remove any
scratches with lapping tape, polishing in an anti-clockwise
direction ONLY. against the crankshaft rotation), lubricate
with clean engine oil and carefully assemble the crank
- shaft into the cylinder block.
1 Fit the thrust washers ensuring that the grooved bearing
Check the crankshaft rotates freely.
1 Fit the remaining new bearing shell halves into the main
1 Lubricate with clean engine oil.
. Fit the caps to the cylinder block.
1 Start off the securing bolts (approximately 2 or 3 turns)
and very gently tap the main bearing caps to ensure they
are seated on the cylinder block.
face contacts
the crankshaft
(1 Fig. 2).
bearing caps.
= Check the crankshaft still rotates freely.
. Pull down each bearing cap individually and torque
1 Check the crankshaft still rotatesfreely after pulling down
tighten
the bolts.
each bearing cap.
Check the crankshaft end-float, see Section 4.12.
. Fit new woodruff keys to the crankshaft, never re-use old
. Fit the timing and oil pump sprockets to the crankshaft.
1 Check the connecting rods for parallelism, twist and bend,
If any connecting rod is unusable, then the complete set
1 Lubricate the small end bush, slide the piston pin through
ones.
using
a suitable measuring jig (Figs.
3 and 4).
must be renewed.
the piston and connecting rod. Fia.
1
Fig. 2
Fig. 3
Fig. 4
Issue 1 August 1994 35

AJ16 Engine Service Manual
Clean all component parts and check for wear or damage,
renew worn or damaged components as necessary.
Check
forwear and renewtheauxiliaryshaft bushes (1 Fig.
1) using Service
Tool 18G 1434 (2 Fig. 1).
. Lubricate all bearing shells. Refit all shells using 18G 1434.
CAUTION: Ensure that the oil feed holes are lined up with the holes in the bearing shell (1 Fig. 2).
. Fit the timing cover blanking plate to the timing cover. Fit and tighten the securing bolts.
Lubricate and fit the auxiliary shaft to the housing.
Lubricate and fit the thrust washer.
. Refit the auxiliary shaft snap-ring.
Fit a new oil seal to the rear of the shaft.
Fit and align the oil pump drive-plate to the auxiliary shaft.
. Apply sealant to the bolt securing the driveplate, fit and
tighten the bolt. See Service Materials in the Preliminary
Pages.
Refit the power assisted steering pump, see Section 10 in
the appropriate Vehicle Service manual.
Fit the new sprocket to the crankshaft.
Using a straight edge (2 Fig. 3). check the alignment of the
oil pump drive sprocket (1 Fig. 3). and the crankshaft
sprocket (4 Fig. 3).
Push back the lock tabs from one bolt securing the oil
pump drive sprocket, and remove the bolt.
. Rotate the sprocket. Push back the locktabs from the sec- ond bolt, and remove the bolt.
m Rotate the sprocket, push back the lock tabs and remove the remaining bolt.
. Remove the tab washer and drive sprocket.
Remove the shims (3 Fig. 3). Calculate the thickness of
shim(s) required for correct sprocket alignment.
Fit and tighten a dummy stud to the oil pump drive flange. Fit and align the shims to the flange. Fit and align the
sprocket.
Fit and align the new tab washer.
Fit and tighten the first sprocket securing bolt. Do not lock
over the tab washer at this stage.
m Rotate the sprocket for access.
. Fit and tighten the second sprocket securing bolt. Lock
m Rotate the sprocket for access.
= Remove the dummy stud.
. Rotate the sprocket for access.
Re-tighten the first securing bolt.
. Re-check the sprocket alignment.
= Re-adjust as necessary.
m Lubricate the newtiming chain and position thechain over
. Lubricate the oil pump drive chain.
. Fit the drive chain to the oil pump sprocket.
* Engage the drive chain to the crank sprocket.
Ensure that the drive chain ends are on the damper side of
If the alignment is incorrect, proceed as follows:
over the
tab washer.
Fit and tighten the third
sprocket securing bolt. Lock over the tab washer.
Lock over the tab
washer.
the auxiliary drive shaft and crankshaft sprocket.
the sprockets.
Fia. 1
I I // , I,
Fia. 2
i Fig. 3
Issue 1 August 1994 38

AJ16 Engine Service Manual
4.20
SRO 12.65.48
Remove the timing cover.
1 Remove the upper tensioner pedestal flanged securing
bolts (3 Fig. 1).
Remove the pedestal / tensioner assembly and chain
damper
(1 Fig. 1).
Remove the tensioner pivot pin (2 Fig. 1) and remove the
tensioner from the pedestal.
. Remove the flanged bolts (5 Fig. 1) securing the upper
static damper and remove the damper (4 Fig. 1) and re-
move the damper pedestal.
1 Remove the lower timing chain tensioner securing bolts (11 Fig. 1) and remove the tensioner assembly (10, 12
Fig. 1).
1 Remove the bolts (16 Fig. 1) securing the oil pump drive
chain damper, remove the damper (17 Fig. 1).
1 Remove the flanged bolts (14 Fig. 1) securing the lower
static damper, and remove the damper
(15 Fig. 1).
Clean all component parts and checkfor wear or damage,
renew worn or damaged components as necessary.
1 Fit the oil pump chain damper in position, do not tighten
the securing bolts
at this stage. Take any slack out of the
chain using hand pressure to push the damper towards
the
center of the engine and tighten the damper securing
bolts.
Timing Chain Damper, Vehicle Set, Renew
1 Refit the lower tensioner assembly.
Refitthe upper static damper. Fit and tighten thesecuring
bolts. Refit the upper tensioner.
Renew the timing cover oil seal and refit the timing cover.
1 13 19 18 17
Fig. 1
Issue 1 August 1994 40