1994 HONDA INTEGRA lifter

Rear Edge Closing Adjustment
Open the glass about a foot, then close it to check where
rear edge begins to rise. lf it rises too soon and seats too
tightly against the roof panel, or too late and does not
seat tightly enough, adjust it.
1. Remove the headliner (see psge 20-98).
2. Remove the glass.
3. Remove the motor {see page 2O-8O).
4. Align the tilt-up position of the lifter on each side.
Check that the alignment left and right. then install
the motor.
Install the glass, then check for water leaks.
NOTE: Do not use high pressure wate..
lnstall the headliner.
Glass and Sunshade Redacernent
1. Open the sunshade.
2. Tilt-up the glass.
3. Remove the bolts, then remove the glass from rheglass bracket.
V : 8oh locations, 6
4. Remove the screw and lift the sunshade rail on each
side.
5. Silde the sunshade
sunshade.
V : Scraw locations, 2
forwa.d, then remove the
SUNSI{ADE
l-tII
)
6
7
Installation is the reverse of the removal procedure.
Check for water leaks.
NOTE: Do not use high pressure water.
GLASS BRACKET
20-79

1.Remove the frame from the car {see page 2O-8O).
Remove the motor (see page 2O-8O).
Remove the drain channel.
NOTE: Take care not to damage, twist or lift theseat.
V : Screw locations, 2
DRAINCHAI{NEL
4. Remove the front drain
V : Clip locations, 2
channel on each side.
GUIDE RAIL
20-81
Glass Bracket/Slider, Lifter, Guide Rails and Cable Assembly Replacement
5. Remove the front rail holder on each side.
V : Nut, scrow locations
AV : f{ut, 2
b.
7.
Remove the anchor spring on each side.
Remove the nuts and screws, then lift and remove
both guide rails and cable assembly from the trame.
Remove the sunshade and both sunshade rails.
BV: Screw,
BV : Sciow, 4
V : Nut, rcrow locations
AV : Nut. 2
NOTE: To instalt, Iill thegtoove rn each grommet with sealant,
GUIDE RAIL
SUNSHADE

Moonroof
Glass Bracket/SliderGuide Rails and Cable Assembly ReplacementLifter
(cont'dl
8. Slide the guide rail fofward, then remove it.
NOTE: Take care not to bend the inner cable.
10.Slide the anchor rod forward, then remove it from
the guide rail.
STOPPER
To install. insort the anchorrod by turning the stopper 9Oo.
qSeparate the glass bracket, lifter, slide stopper link
and slider,
AIT|CHOB ROD
1 1 . lnstallation is the reverse ol the removal procedure.
NOTE:
a Dsmsged pans should be replaced.
. Apply grease to the sliding portion.
SLIOER
NOTE: To inst€ll, apply multipurpose grease tothe lifter and slide stooDer link.
CABLE ASSEMBLY
GUIDE RAIL
INNER CABLEGLASS
20-82
'-

Moonroof
Rear Edge Closing Adjustment
Open the glass about a foot, then close it to check where
rear edge begins to rise. It it rises too soon and seats too
tightly against the roof panel, or too late and does not
seat tightly enough, adjust it.
1. Remove the headliner (see page 20-1OO).
2. Remove the glass.
3. Remove the motor (see page 20-87).
4. Align the tilt-up position of the lifter on each side.
o.
5.
7.
Check that the alignment lett and right, then install
the motor.
Install the glass. then check for water leaks.
NOTE: Do not use high pressure water.
Install the headliner.
Glass and Sunshade Replacement
1. Open the sunshade.
2. Tilt-up the glass.
3, Remove the bolts, then remove the glass from the
glass bracket.
Using the moonroof
BOLTS6 x 1.O mm9.8 N'm lt O kgf m,
4.
5.
7.2 tbt.ftl
Remove the screws and lift the sunshade rails.
Silde the sunshade forward. then remove the
sunsnaoe.
SUlTSHADERAIL
Installation is the.everse ot the removal procedure.
Check for water leaks.
NOTE: Do not use high pressure water.
GLASS BRACKET
20-86

Moonroof
Remove the frame (see page 20-87).
Remove the drain channel.
NOTE: Take care not to damage, twist or litt the
seal.
4. Remove the motor (see page 20-87).
5. Remove the front drain channel.
6. Remove the nut, then remove the front rail holder.
9.8 N.m {1.O kgf.m,7 .2 tbt-lrl
9, Slide the glass bracket/slider, liJter backward, then remove it.
Glass Bracket/Slider, Lifter, Guide Rails and Cable Assembly Replacement -
1.
2.
3. Remove the screws, then remove the sunshade rail
by sliding it backward.
ITUT6xl.Omm9.8 t{.m {1.0 kgt.m,7.2 tbf.ttl
7. Remove the screws @ attsching the guide rail. then litt the guide rail.
8. Remove the nut. then remove the rear rail holder.
NOTE: Remove the anchor spring.
AI{CHOR
NUT6 x 'l.O mm
REAR RAILHOLDER
NOTE: Install the rear railthe sub-seal to the trame.
SUB-SEAL
holder, then glue
SUNSHADE RAIL
SCREW
20-88

10. Separate the glass bracket, lifter, slide stopper lankand slider.
GLASSLIFTER BRACKET
SLIDER
NOTE: To install, apply muttjpurpose grcaseto th€ liftsr and slide stopper link.
1 1. Slide the anchor rod forward, then remove it fromthe guide rail.
INNER CABLE
STOPPER
To install, inson tho anchorrod by turning tho stopper 9Oo
AI{CHOR ROD14.
20-89
GUIDE RAIL
12.Slide the guide rail backward, then remove th€ gude
rail from the inner cable.
NOTE: To install. apply the caulking ro gurde rarlmount faces of the frame.
Apply caulking beforeinsta ing the guide rait.
Remove the screws, then remove the cable assem-
bly from the frame.
NOTE: Take care not to bend the cable pipes.
NOTE: lo install, fill the groove ineach grommet with sealant.
Installation is the reverse of the .emoval procedure.
NOTE:
a Damaged psrts should be replaced.a Apply grease to the sliding portion.
13.
FRAME