1994 HONDA INTEGRA Idle

Intake Air System
Throttle cable [81881 enginel
1 1-1 18
Inspection/Adiustment
'I . Start the engine. Hold the engine at 3,000 rpm with
no load (A/T in $ or@ oosition, M/T in neutral) until
the radiator fan comes on, then let it idle.
2. Check that the throttle cable operates smoothly with
no binding or sticking. Repair as necessary.
3. Check cable free play at the throttle linkage. Cable
deflection should be 1O-12 mm (O.39-O.47 in.)
DEFLECTION1O- 12 mm1O.39-0.47 in.l
4.lf deflection is not within specs, loosen the locknut
and turn the adjusting nut until the deflection is as
specifled.
With the cable properly adjusted. check the throttle
valve to be sure it opens fully when you push the
accelerator pedal to the floor. Also check the throt-
tle valve to be sure it returns to the idle oosition
whenever you release the accelerator pedal.
Installation
1. Fully open the throttle valve. then install the throt-tle cable in the throttle linkage and install the cablehousing in the cable bracket.
2. Start the engine. Hold the engine at 3,OOO rpm withno load (A/T in S or @ position, M/T in neutrall untilthe radiator tan comes on, then let it idle.
THBOTTLE LII{KCABLEARACKET
i;
-l-r
,)
j
5.
LOCKNUTITINER CABLE
Hold the cable sheath, removing all slack from the
cable.
Turn the adjusting nut until it is 3 mm (O. 12 in.) away
trom the cable bracket.
Tighten the locknut. The cable deflection should now
be 10- 1 2 mm (O.39 -O.47 in.). lf not, see Inspec-
tion/Adjustment.
3 mm {0.12 in)
LOCKNUT1O N.m{1.O kgl.m,7 tbt.ft)

Throttle cable [B18C1 enginel
Inspection/Adiustment
1 . Start the engine. Hold the engine at 3,O0O lpm with
no load in neutral until the radiator fan comes on,
then let it idle.
2. Check that the throttl€ cable operates smoothly with
no binding or sticking. Repair as necessary.
3. Check csble free play at the throttle linkage, Cable
deflection should be 10-12 mm (O.39-O.47 in.)
DEFLECTIOI{10-12 mm(O.39-O.47 in.l
lf deflection is not within sDecs, loosen the locknut
and turn the adjusting nut until the deflection is as
specitied.
With the cable properly adjusted, check the throttle
valve to be sure it opens fully when you push the
accelerator Dedal to the tloor. Also check the throt-
tle valve to be sure it retums to the idle position
whenever vou release the accel€rator pedal.
CABLE BBACKET
ADJUSTING I{UT
lnstallation
1. Fullv open the throttle valve, then install the throt-
tle cable in the throttle linkage and install th€ cable
housing in the cable bracket.
2. Stan the engine. Hold the engine at 3,OOO rpm with
no load in neutral until the radiator fan comes on,
then let it idle.
THROTTLE LI K
With part A of the cabl€ bracket, support the cable
sheath so that there is no inner wire free play. Turn
the adjusting nut until it touches part A, leaving a
gap between the locknut and adiusting nul.
Move the cable sheath to psrt B of the cable brack-
et that so the bracket slides into the gap between
the locknut and adiusting nut. Tighten the locknul.
LOCKT{UTlO t{.m (t.O kgl.m, pART B
5.
4.
7 lbt.ftl{Locked by bracket)ADJUSTING NUT
PABT A
LOCKNUTNO GAP
AIUUSTINGNUT
5, The cable deflection should now be 10-12 mm
{O.39-O.47 in.). lf not, see Inspection/Adiustmsnt
11-119

lntake Air System
Throttle Body
Description
The throttle body is ot the single-barrel side-draft 1ype.
The lower portion of the throttle valve is heated by en-gine coolant from the cylinder head. The idle adjusting
screw which increases/dec.eases bvDass air and the
Evaporative Emission (EVAP) Control Canister port are
located on the top of the throttle body.
IOLE AOJUSTING
THROTTLESTOP SCREW(Non-adiustsb16l
11-120
Insoection
CAUTION: Do not adiust the thlottle stop screw. lt ispreset at the lactory.
1. Start the engine. Hold the engine at 3,OOO rpm with
no load (A/T in S or E position, M/T in neutral) until
the radiator fan comes on, then let it idle.
2. Disconnect the vacuum hose (to the EVAP control
canister) from the top of the throttle body; connect
a vacuum, gauge to the throttle body.
VACUUM PUMPGAUGEA973X-O41-XXXXX
5.
3. Allow the engine to idle and check that the gauge
indicates no vacuum.
a li there is vacuum, check the throttle cable (see
page 1 1-'l 18, 119).
Check that vacuum is indicated on the gauge when
the throttle is opened slightly from idle.
a lf the gauge indicates no vacuum, check the throt-
tle body port. lf the throttle body port is clogged.
clean it with carburetor cleaner.
Stop the engine and check that the throttle cable
operates smoothly without binding or sticking.
a lf there are any abnormalities in the above steps,
check for:
- Excessive wear or Dlav in the throttle valve shaft.
Sticky or binding throttle lever at full close po-
srtron.
Clearance between throttle stop screw and throt-
tle lever at tull close Dosition.

Intake Air System
Throttle Body (cont'dl
11-122
Dirarssmbly
GAUTION:
a Ths throttlo stop scrow is non-adrustablo.
a Aftar reassombly, adiust rhr throttlo Gablo (pago 11-118, 1 19). and A/T throttlo contlol cabl6 (section 14) for c!r8
rYith A/T.
a Tho TP sonaor ir not lomovablo
MAPSENSORTroubleshootingpage 11-52
TPSETSORTroubleshootingpoge 1l-60
O.BING
I
d^'%
IDLE ADJUSTINGSCREW
o-RtftGReplace.
FAST IDLETHERMOVALVEInspection, page 11-94
1O N.m11.O kgl.m.7 tbf.ftl

Intake
Intake
Air
Air
System
Bypass (lAB) ControlSystem tBl8C1 enginel (cont'dl
Troublcahooting
VACUUII PUMP/GAUG€A973X-041-XXXXX
fromwiro haanasid€
PI{K/BLU I-I
YEI/aLK l+l
tA8 COI{TROLDIAPHRAGM
Insp€ction of IAB Conltol Sytt.m
Start engino and allow to idle.
R€move # 13 vacuum hose tromthe IAB control diaph.agm andconnect vacuum gauge to thehose.
R€move # 12 vacuum hose fromth€ IAB vacuum tank, then checktor vaccum at the IAB vacuumtank.
Rcplir lh. block.g. otvacuufi laak boiwaaotha IAB vacuum tanklnd th. intlk m!ni-fold.
Disconnect the 2P conn€ctor lromthe IAB control solenoid valve.
Measure voltage betweenYEL/BLK (+l torminal andPNK/8LU l-) terminsl.
ls thoro battery voltage?
Measure voltage b€twee nBLK^|/EL (+) torminal and bodyground.
IAB CONTBOLSOLENOID VALVE

a
Intake Air System
Intake Air Bypass (lABl Control Valve IB18C1 enginel
Trlting
GAUTIOI{; Do not rdlust lho IAB control valvo tull-close screw. lt is prosot at th. t.ctoty.
1. Chsck the IAB control valve shsft for binding or sticking.
2. Check th6 IAB control valve for smooth movement.
3. With the engine at idle, check that @ot the IAB control valve is in close contact with the stoppsr when vacuum
hose is disconnected.
With th€ ongine at idl6, check that @of the IAB control valve is in close contact with the full-closo acrew whsn
the vacuum hose is connectad.
a lf 8ny fault is lound, clean the linkage and shatts with carburetor claaner'
- lf the oroblam still exists after cleaning, disassemble the intake manifold and check the IAB valvE body sss8mbly.
11-126

Emission Control System
System Troubleshooting Guide
NOTE: Across each row in the chart, the sub-systems that could be sources of a symptom are lanked in the ord€r they
should be inspected starting with O. Find the symptom in the lett column, read across to the most likely source, then
reJer to the page list€d at the top of that column. lf inspection shows the system is OK, try the next most likely system
@, etc.
PAGE
SYMPTOM
SUB.SYSTEMTHREE WAY
CATALYTIC
CONVERTER
POSITIVE
CRANKCASE
VENTILATION
SYSTEM
EVAPORATIVE
EMtSSTON
CONTROLS
11-132, 1331 1- 13411tJo
ROUGH IDLEo
POOR PERFORMANCE
FAILS
EMISStON
TEST
o@
LOSS OF
POWERo
11-129

Emission Control System
SystemDescription
The emission control system includes a Three Way Cata-
lytic Convener (TWC), Positive Crankcase Ventilation(PCV) system and Evaporstive Emission {EVAP) Contfol
syst€m. The emission control system is designed to meet
federsl and stats emission standards.
Tailpipe Emission
Inspection
f!fifil oo nor amoro ou]rng rnr! Foacqurr. ^!op
any open flame away from yout wotk atca.
Start the engine. Hold the engine at 3,OOO rpm with
no load (A/T in @ or@ position, M/T in neutral) until
the radiator fan comes on, then let it idle,
Connect a tachometer.
Check and adiust the idle speed, if necessary (sss
page 1 1-95).
Warm up and calibrate the CO meter according to
the meter manutacturer's inst.uctions.
Check idle CO with the headlights, hester blower,
rear window defogger, cooling fan, and air condition-
er otf.
NOTE: (Canada) Pull the parking br8ke lever up.
Stan the engine, then check that the headlights are
off.
CO meter should indicate 0.1 maximum.
11-130