1994 HONDA INTEGRA engine

*l
Engine Removal/lnstallation
(cont'dl
27. Remove the radiator assembly {see page 1O-4),
28. Remove the A/C compressor.
a Do not disconnect A/C hoses.
8 x '1.25 mm24 N.m t2.4 kgf.m, 17 lbl.ftl
29. Disconnect the heated oxygen sensor (HO2Sl con-nector, then remove exhaust pipe A.
B'l8Cl engine: Ho2s
I x 1.25 mm24 N.m (2.4 kgf.m,17 rbt.ftt
Replace.
SELF-LOCKING NUT8 x 1.25 mm16 N.m 11.6 kgf.m,12 tbl.ftlReplace.
EXHAUSTPIPE A
SELF10 x 1.25 mm54 N.m (5.5 ksf.m.4O lbf'ltlReplace.
CONNECTOR
5-8
8188l engine:
8 x 1.25 mm24 N.m 12.4 kgf.m,17 tbt.trl
GASKETReplace.
GASKETReplace.
SELF.LOCKING NUTI x 1.25 mm16 N.m (1.6 kgt.m,12 tbf.ft)Replace.10 x 1.25 mm54 N.m (5.5 kgl.m,40 tbt.ttlReplace.
30. Remove the shift rod and extension rod {M/T).
I x 1.25 mm22 N-m 12.2 kgf.m, '16 lbf.ftlSHIFT ROD

31. Remove the shift cable
I x 1.25 mm22 f.m 12.2 kgl'rn'16 tbl.ftl
(A/T).
SHIFT CABLE
32.
33.
CONTROLLEVER
SHIFT CAALEcovER locx usiea6 x 1.0 mm14 N.m t1.4 kgf.m, 10 lbl'ftlReplace.
Remove the damper tork.
Disconnect the suspension lower arm balljoints us-
ing the special tool. Refer to section 1 8 tor the proper
procedure.
NOTE: Adjust the tool so the iaws are parallel to
each other.
REMOVER 28 mmoTMAC-S10020012 x 1.25 mm
5-9
34. Remove the driveshatls.
CAUTION:
a Do not pull on tho ddv$halt, tho CV ioint mav
como apan.
a Uso caro whsn prying out tho assombly.
Pult it slraight to avoid damaging th6 differantial
oil soal or intormodiato shaft dust seal.
NOTE: Coat all precision tinished surfaces with
clean engine oil or grease. Tie plastic bags over the
driveshaft ends.
(cont'd)

Engine Removal/lnstallation
I
II
I
I
I
(cont'd)
35. Lower the hoist.
36. Attach the chain hoist to the engine.

37, Remove the left and right front mounts and brackets.
MOUNT BOLT
LEFT FRONTMOUNT
12 t 1.25 nn59 N.m {6.0 kgt.m,43 lbf.trlReplace.
38. Remove the rear mount bracket,
12 r 1.25 mm59 N.m (6.0
Replace.43 rbf.ftl
REAR MOUNT12 r 1.25 m|n59 N.m {6.0 kgt.m,43 tbt.frlReplace.
14 x 1.5 mm118 t{.m (12.O kgt.m,86.8 lbl.ft}R6place.
MOUNT/BRACKET
39. Remove the side engine
10 r 1.25 mm
mounr.
WASHERSReplace.Replace.SIDE ENGIITE
40. Remove the transmission mount
TRA SM|SS|OI{MOUNT
41. Check that the engine is completely free of vacuum
hoses, fuel and engine coolant hoses, and electrical
wi.ing.
42. Slowly raise the engine approximately 150 mm (6
in), Check once again that all hoses and wires are
disconnected from the engine
43. Raise the engine all the w8y and remove it trom the
car.
(cont'dl
5-11

Engine Removal/lnstallation
SIDE ENGITIEMOUNT
5-12

Engine Installation
Install the engine in the reverse order of removal.
Reinstall the mount bolts/nuts in the following sequence.
Failure to tollow these procedures may cause excessive
noise and vibration, and reduce bushing life.
1. Install the transmission mount, then tighten the
bolt/nuts on the transmission side. Leave the mount
bolt loose.
A/T:
12 x 1.25 mm64 N.m (6.5 kgt.m,47 rbf.ft)
M/T:
12 x 1.25 mm64 N.m 16.5 kgl.m,47 tbt.frl
Install the engine side mount, then tighten the
bolt/nuts on the engine side. Leave the mount bolt
loose.
10 x 1.25 mm52 N.m {5.3 kgf.m,38 rbf.ItlReplace.
3. Tighten the mount bolt on the transmission mount.
A/T:
12 x 1 .25 nn
M/T:
74 N.m (7.5 kgl.m,54 rbf'ftt
12 x 1.25 mm74 N.m (7.5 kgt.m,54 tbt.ftl
{cont'd)
5-13

Engine Removal/lnstallation
.tE
m'
(cont'dl
4. Tighten the mount bolt on the side engine mount.
12 x 1.25 mm74 N.m (7.5 kgf.m,54 lbt.ttl
5. Install the rear mount bracket, then tighten the bolts
in the numbered sequence as shown {@ @).
@ 12 x 1.25 mm59 N.m {6.0 kgf'm, 43 lbl'It)Replace.
12 r 1.25 mm59 .m 16.0 kgl.m,
6. Install the right front mount/bracket, then tighten the
bolts in the numbered sequence as shown (O-@).
A/T:@ 10 x '1.25 mm44 N.m (4.5 kgt'm,33 tbt.fr)
O 12 x 1.25 mm64 N.m 16.5 kgt.m,47 lbf.ftlReplace.
M/T:
O 12 x 1.25 mm83 N'm (8.5 kgf.m, 61 lbt.frl
@ '10 x 1.25 mm44 N-m (4.5 kgf.m,

SIDE ENGINE MOUNT:
LEFT FRONT MOUNT:
/>
Torqus Spocifications:
A: 10 x 1.25 mm
59 N.m (6.O kgf.m, 43 lbf.ft)
B: 12 x 1.25 mm
59 N.m {6.0 kgt.m. 43 lbt.ft}
Reolace.
C: 14 x 1.5 mm
118 N.m {12.O kgt.m,86.8 lbt.tt}
Replace.
D: 12 x 1.25 mm
74 N.m {7.5 kgf.m, 54 lbf.tt}
E: 12 x 1.25 mm
64 N.m (6.5 kgf.m, 47 lbf.ftl
F: 10 x 1.25 mm
52 N.m {5.3 kgl.m, 38 lbt.ft}
Replace.
G: 10 x 1.25 mmrt4 N.m (4.5 kgf.m, 33 lbf.ft)
H: 12 x 1.25 mm
83 N.m (8.5 kgt.m. 61 lbl.ft)
lr 12 x 1.25 mm
64 N.m (6.5 kgf.m, 38 lbf.tt)
Reolace.
{cont'd)
5-17