1994 CHEVROLET ASTRO PASSENGER coolant

Downloaded from www.Manualslib.com manuals search engine What to Use
Refer to the Maintenance Schedule to determine what kind of lubricant to
use. See “Recommended Fluids
and Lubricants” in the Index.
Engine Coolant
The following explains your cooling system and how to add coolant when it
is low. If
you have a problem with engine overheating, see “Engine
Overheating” in the Index.
The proper coolant for your vehicle will:
0 Give freezing protection down to -20°F (-29”C), or -34°F (-37°C) in
0 Give boiling protection up to 258°F (125 “C).
0 Protect against rust and corrosion.
0 Help keep the proper engine temperature.
0 Let the warning gages work as they should.
Canada
and for vehicles with the cold climate option.
What to Use
Use a mixture of one-half clean water (preferably distilled) and one-half
antifreeze
that meets “GM Specification 6038-M,” which won’t damage
aluminum parts. You can also use a recycled coolant conforming to
“GM
Specification 603%”’ with a complete coolant flush and refill. If you use
this mixture,
you don’t need to add anything else.
6-26

Downloaded from www.Manualslib.com manuals search engine I NOTICE:
If you use an improper coolant mix, your engine could overheat
and be badly damaged. The repair cost wouldn’t be covered by
your warranty. Too much water in the mix can freeze and crack
the engine, radiator, heater core and other parts.
Some conditions, such as air trapped in the cooling system, can affect the
coolant level
in the radiator. Check the coolant level when the engine is cold
and follow the steps under “Adding Coolant” for the proper way to add
coolant.
If you have to add coolant more than four times a year, have your dealer
check your cooling system.
I NOTICE:
If you use the proper coolant, you don’t have to add extra
inhibitors or additives which claim to improve the system. These
can be harmful.
Adding Coolant
To Check Coolant
When your engine is cold, the coolant level should be at COLD LEVEL, or
a little higher. When your engine is warm, the level should be up
to COLD
LEVEL, or a little higher.
6-27

Downloaded from www.Manualslib.com manuals search engine To Add Coolant
-3 If you need more
coolant, add the
proper
mix at the
coolant recovery tank.
Add coolant mix at the recovery tank, but be careful not to spill it.
6-28

Downloaded from www.Manualslib.com manuals search engine Radiator Pressure Cap
NOTICE:
Your radiator cap is a 15 psi (105 kPa) pressure-type cap and
must be tightly installed to prevent coolant
loss and possible
engine damage from overheating. Be sure the arrows on the cap \
line up with the overflow tube on the radiator filler neck.
When you replace
your radiator pressure
cap, an
AC@ cap is
recommended. See
“Service Replacement
Part and Filler
Recommendations”
in
the Index.
Thermostat
Engine coolant temperature is controlled by a thermostat in the engine
coolant system. The thermostat stops
the flow of coolant through the
radiator until the coolant reaches a preset temperature.
When you replace your thermostat, an
AC’ thermostat is recommended.
6-29

Downloaded from www.Manualslib.com manuals search engine Explanation Of Scheduled Maintenance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed
in this section. Make sure
whoever services your vehicle uses these. All parts should
be replaced and
all necessary repairs done before you or anyone else drives the vehicle.
1.
2.
3.
4.
5.
ENGINE OIL AND OIL FILTER CHANGE“ - ALWAYS USE
API SERVICE
SH OR SG ENERGY CONSERVING I1 OILS OF THE
PROPER VISCOSITY. The
“SH7 or “SG7 designation may be shown
alone or in combination with others, such as “SWCD”, or
“SH, SG,
CD,” or “SG/CD”, etc. To determine the preferred viscosity oil for your
vehicle’s engine see “Engine Oil”
in the Index.
CHASSIS LUBRICATION - Lubricate the front suspension,
steering linkage, transfer case shift linkage, parking brake cab\
le guides,
and brake pedal springs at the intervals specified on the proper
maintenance schedule, or at every engine oil change, whichever \
comes
first.
Ball joints and king pin bushings should not be lubricated unless their
temperature is
10°F (-1 2°C) or higher. When the weather is cold, let
them warm up before lubricating them or they could be damaged.\

Also, be sure to check all the vehicle fluid levels at this \
time.
COOLING SYSTEM SERVICE* - Drain, flush and refill the
system
with new or approved recycled coolant conforming to “GM
Specification 6038-M”. See “Engine Coolant”
in the Index for the
proper coolant and mixture to use
in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Clean the outside of the radiator and air conditioning
condenser. Wash the radiator neck.
To ensure proper operation,
pressure test the radiator and cap.
AIR CLEANER FILTER REPLACEMENT* - Replace at
specified intervals. Ask your dealer for the proper replacement
intervals for your driving conditions.
FRONT WHEEL BEARING REPACK
(2-WHEEL DRIVE ONLY)
- Clean and repack the front wheel
bearings at each brake relining,
or at the specified interval, whichever
comes first.
* An Emission Control Service
7-7

Downloaded from www.Manualslib.com manuals search engine Recommended Fluids & Lubricants
NOTE: Fluids and lubricants identified below by name, part number or
specification may be obtained from your GM Dealer.
USAGE
Engine Oil
Engine Coolant Hydraulic Brake Systems
Parking Brake Cable
Power Steering System
Manual Steering Gear
Automatic Transmission
Differential: a. Standard
- Front and
Rear Axle
b. Locking
Transfer Case Column Shift
FLUIDLUBRICANT
API service SH or SG Energy
Conserving I1 oils
of the proper
viscosity. The “SH” or
“SG’
designation may be shown alone or in
combination with others, such as
“SWCD”, or
“SH, SG, CD,” or
“SGKD”, etc. To determine the
preferred viscosity oil for your
vehicle’s engine (e.g. SAE 5W-30).
See “Engine Oil”
in the Index.
Mixture of water and a good quality
ethylene glycol base antifreeze or an
approved recycled coolant conforming
to GM Specification GM-6038-M
(GM Part No. 1052103).
Delco Supreme I1 brake fluid
(GM
Part No. 1052535 or DOT-3).
Chassis lubricant meeting
requirements of NLGI Grade 2,
Category LB or GC-LB or (GM Part
No. 1052497).
GM Hydraulic Power Steering Fluid
(GM Part No. 1052884) or equivalent.
GM Lubricant (GM Part
No. 10521 82) or equivalent.
DEXRON @-I11
is preferred, if
unavailable use DEXRON @-IIE .
a. SAE-80W-90 GL-5 gear lubricant
(GM Part
No. 105227 1).
b. SAE-80W-90 gear lubricant (GM
Part
No. 1052271).
DEXRON@-IIE Automatic
Transmission Fluid.
Chassis lubricant meeting
requirements of NLGI Grade 2,
Catagory LB or GC-LB
(GM Part
No. 1052497).
7- 13

Downloaded from www.Manualslib.com manuals search engine Service Station Checks
It is important for you or a service station attendant to perform these
under-hood checks at each fuel fill.
0 Check the engine oil level and add if necessary.
Check the engine coolant level and add if necessary.
Check the windshield washer fluid level and add if necessary.
See the Index under these items for information on how to check them.
7-16

Downloaded from www.Manualslib.com manuals search engine needs no water. I
See Page 6-35.
Brake Fluid
Reservoir
See Page 6-32. 1
Automatic A
Transmission
Fluid
See Page 6-20.
Fuel
Capacity
27 US. Gal.
(102 L.). Use
unleaded
gas
only. 87 octane
or higher.
See Page 6-3.
!
Hood Release
Lever
See Page 6-7.
Engine Oil
See Page 6-9.
Battery
The Delco
Freedom battery
-
-
-
11 't- i
--I!
fil I
I! I '" 1, 1. .
Cooling
System
Check and add
coolant only at
the coolant recovery tank.
See Page 6-26.
' Windshield
Washer
Fluid
See Page 6-31.
3
bower
Steering Reservoir
See Page 6-30.
4 Spare Tire
' Pressure
Compact Spare
See Page 6-48.

Cold Tire
Pressure
See Tire Loading
label on the
driver's
door.
See Page 6-44.
7- 17