1994 CADILLAC SEVILLE check engine

Downloaded from www.Manualslib.com manuals search engine Air Bag Readiness Light
There is an air bag readiness light on the instrument panel, which has
“INFL REST.” or “INFLATABLE RESTRAINT” on it. The system
checks for electrical malfunctions, and the light tells you
if there is a
problem.
INFLATABLE
RESTRAINT
You will see this light
flash for a
few
seconds when you
turn your ignition to
“Run” or “Start.”
Then the light should
go out, which means
the system is ready.
Remember,
if the air bag readiness light doesn’t come on when you start
your vehicle, or stays on,
or comes on when you are driving, your air bag
system may not work properly. Have your vehicle serviced right away.
.-
33

Downloaded from www.Manualslib.com manuals search engine SAFETYBELT EXTENDER
If the vehicle’s safety belt will fasten around you, you should use it.
But
if a safety belt isn’t long enough to fasten, your dealer will order you
an extender. It’s free. When you go in to order it, take the heaviest coat
you will wear,
so the extender will be long enough for you. The extender
will be just for you, and just for the seat in your vehicle that you choose.
Don’t let someone else use it, and use it only for the seat it is made
to fit.
To wear it, just attach it to the regular safety belt.
CHECKIING YOUR RESTWNT SYSTEMS
Now and then, make sure all your belts, buckles, latch plates, retractors,
anchorages and reminder systems are working properly.
Look for any
loose parts or damage. If you see anything that might keep a restraint
system from doing its job, have it repaired.
REPUCING SAFETYBELTSAFTER A
CRASH
If you’ve had a crash, do you need new belts?
After a very minor collision, nothing may be necessary. But if the belts
were stretched, as they would be
if worn during a more severe crash, then
you need new belts.
If belts are cut or damaged, replace them. Collision damage also may
mean you will need to have safety belt or seat parts repaired or replaced.
New parts and repairs may
be necessary even if the belt wasn’t being used
at the time of the collision.
63

Downloaded from www.Manualslib.com manuals search engine Anti-Lockout Feature
Your vehicle is equipped with this feature. If you leave the key in the
ignition whether in the Accessory, Lock, or
Off position with the driver’s
door open, you cannot lock your vehicle using the power locks.
If you
close
the door you can lock it using the Remote Keyless Entry System. It
is always recommended that you remove your ignition key when locking
your vehicle.
Illuminated Entry System
Your illuminated entry system turns on all the courtesy lights when either
front door is opened. When the door is closed, the courtesy lights will stay
on for approximately 20 seconds or until the ignition is turned on.
REMOTE KEIZESS ENTRY SYSTEM
With this feature you can turn on your interior lights, lock and unlock
your doors, or unlock your trunk from up to
15 feet (4.5 m) using the key
chain transmitter supplied with your vehicle.
Your Remote Keyless Entry System is intended to be used as a
supplementary vehicle entry device. It is not intended to replace, but
rather should
be used in conjunction with a door lock key. It operates on
a radio frequency subject to Federal Communications Commission
(FCC) Rules.
This device complies with Part
15 of the FCC Rules. Operation is subject
to the following
two conditions: (1) This device may not cause harmful
interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Should interference to this system occur, try this:
Check to determine if battery replacement is necessary. See the
instructions on battery replacement.
0 Check the distance. You may be too far from your vehicle. This
product has a maximum range.
a Check the location. Other vehicles or objects may be blocking the
0 See your Cadillac dealer or a qualified technician for service.
signal.
71

Downloaded from www.Manualslib.com manuals search engine Remember, the theft deterrent system won’t arm if you lock the doors
switch or Keyless Entry System.
- with a key or manual door lock. It arms only if you use a power door lock
Here’s how to avoid setting
off the alarm by accident:
If you don’t want to arm the theft deterrent system, the vehicle should
-
be locked with the door key after the doors are closed.
Always unlock a door with a key, or use the Keyless Entry System.
If you set
off the alarm by accident, unlock any door with your key. You
can also turn off the alarm by using the Keyless Entry System, if you have
it. The alarm won’t stop if you try to unlock a door any other way.
Unlocking a
door any other way will set
off the alarm.
__ How to Test The Alarm
From inside the vehicle roll down your window, then get out of your
From outside the vehicle with the door open, lock the vehicle using
Reach in and unlock the door using the manual lock, and open the
vehicle
keeping the door open.
the power door lock or the Keyless Entry System and close the door.
door. The horn will sound and your headlights will flash.
If the alarm does not sound when it should, check to see if the horn
works. The horn fuse may be blown.
To replace the fuse, see “Fuses and
Circuit Breakers” in the Index.
To reduce the possibility of theft, always arm the theft deterrent system
when leaving your vehicle.
81

Downloaded from www.Manualslib.com manuals search engine PASS-KEY’II
Your vehicle is equipped with the PASS-Key’II (Personalized
Automotive Security System) theft deterrent system. PASS-Key’II is a
passive theft deterrent system. This means you don’t have to do anything
different to arm or disarm the system. It works when you insert or remove
the key from the ignition. PASS-Key@II uses a resistor pellet in the
I*
ignition key that matches a decoder in your vehicle.
-
When the PASS-Key’II system senses that someone is using the wrong key,
it shuts down the vehicle’s starter and fuel systems. For about three minutes,
the starter won’t work and fuel won’t
go to the engine. If someone tries to
start your vehicle again or uses another key during this time, the vehicle
will
not start. This discourages someone from randomly trying differe\
nt keys
with different resistor pellets
in an attempt to make a match.
The ignition key must be clean and dry before it’s inserted in the ignition
or the engine may not start. If the engine does not start and the
“STARTING DISABLED DUE TO THEFT SYSTEM REMOVE
IGNITION
KEY” message is displayed, the key may be dirty or wet.
Turn the ignition off.
Clean and dry the key. Wait about three minutes and try again. The
security light may remain on during this time.
If the starter still won’t
work, and the
key appears to be clean and dry, wait about three minutes
and
try the other ignition key. At this time, you may also want to check
the fuses (see “Fuses and Circuit Breakers” in the Index).
If the starter
won’t work with the other key, your vehicle needs service. If your vehicle
does start, the first ignition
key may be faulty. See your Cadillac dealer or
a locksmith who can service the PASS-Key’II.
If you accidentally use a key that has a damaged or missing resistor pellet,
the starter won’t work But you don’t have to wait three minutes before
trying one of the other ignition keys.
See your Cadillac dealer or a locksmith who can service the PASS-Key’II
to have a new key made.
If you’re ever driving and you get the “PASS-KEY MALFUNCTION’ -
message you will be able to restart your engine if you turn it off. Your
PASS-Key’II system, however,
is not working properly and must be serviced by
your Cadillac dealer. Your vehicle is not protected by the PASS-Key’II system.
-
If you lose or damage a PASS-Key@II ignition key, see your Cadillac dealer -
or a locksmith who can service PASS-Key’II to have a new key made.
82

Downloaded from www.Manualslib.com manuals search engine NOTICE:
Your engine is designed to work with the electronics in your
vehicle.
If you add electrical parts or accessories, you could
change the
way the fuel injection system operates. Before
adding electrical equipment, check with your dealer.
If you
don’t, your engine might not perform properly.
If you ever have to have your vehicle towed, see the part of this
Manual that tells how to do it without damaging your vehicle.
See “Towing Your Vehicle” in the Index.
ENGINE COOLANT HEATER (ENGINE
BLOCK HEATER) (CANADA ONLY)
(OPTION)
In very cold weather, 0°F (-18O C) or colder, the engine coolant warmer
can help. You’ll get easier starting and better fuel economy during engine
warm-up. Usually, the coolant warmer should be plugged in a minimum
of four hours prior to starting your vehicle.
To use the coolant warmer:
1. Turn off the engine.
2. Open the hood and unwrap the electrical cord.
3. Plug it into a normal, grounded 110-volt outlet.
-
t. *

Downloaded from www.Manualslib.com manuals search engine As you signal a turn or a lane change, if the arrows don’t flash but just
stay on, a signal bulb may be burned out and other drivers won’t see your
turn signal.
If a bulb is burned out, replace it to help avoid an accident. If the green
arrows don’t go on at all when you signal
a turn, check the fuse (see
“Fuses” in the Index) and for burned-out bulbs.
Operation of Lights
Although your vehicle’s lighting system (headlights, parking lights, fog
lamps, side marker lights and taillights) meets all applicable federal
lighting requirements, certain states and provinces may apply their own
lighting regulations that may require special attention before you operate
these lights.
For example, some jurisdictions may require that you operate your lower
beam lights with fog lamps at all times, or that headlights be turned on
whenever you must use your windshield wipers. In addition, most
jurisdictions prohibit driving solely with parking lights, especially at dawn
or dusk. It is recommended that you check with your own state or
provincial highway authority for applicable lighting regulations.
Yeadlight High-Low Beam
To change the
headlights from low
beam to high or high to
low, pull the turn signal
lever all the way toward
you. Then release
it.
When the high beams
are on, this blue light
on the instrument
panel also
will be on.
105

Downloaded from www.Manualslib.com manuals search engine Heavy snow or ice can overload your wiper motor. A circuit breaker will
stop the motor until it cools. Clear away snow or ice to prevent an
overload.
Windshield Washer
I
To wash your
windshield push and
hold the paddle
labeled
PUSH. Once
you feel you have
enough washer fluid
on the windshield
release the paddle.
The wipers will
continue to clear the
windshield, then either
stop or return to your
preset speed.
When the washer fluid reaches a low level,
“LOW WASHER FLUID”
will be displayed in the Driver Information Center.
Driving without washer fluid can be dangerous.
A bad mud splash can
block your vision.
You could hit another vehicle or go off the road. Check
your washer fluid level often.
108